Search Documents

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By Denise Corrêa de Oliveira

Common dry batteries use zinc as the negative electrode. Producers commonly use additives such as mercury to prevent corrosion and to increase the mechanical resistance of the zinc anode. Alkaline batteries also contain it, as an anti-corrosive agent. When mixed with the common municipal solid waste, heavy metals as zinc and mercury pollute soil and ground water supplies, moving to the food-chain and affecting human health. Due to these possible damages, this kind of waste must be properly disposed, or recycled. Thus, even in low amounts (ppm) in batteries, mercury has to be eliminated or, at least, its content should be reduced. This work presents the use of pyromettalurgical processes, to reduce mercury content and recover zinc. The tests involved batteries treatment at temperatures from 300° to 1000°C. Mercury is eliminated up to 650°C, and zinc is evaporated at higher temperature treatment. C

Jan 1, 2001

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By Eduardo Juncal, Jorge Alberto Soares Tenorio, Jose Roberto de Oliveira, Denise Crocce Romano Espinosal

"Steel industry has been expanding every year, consequently there has been an increase in waste generation in this area. Thus, companies in this sector are finding it difficult to give a correct destination of waste. For example, only in a basic oxygen furnace (BOF) converter are generated about l8kg of dust per ton of steel. The aim of this work was the characterization of dust generated in the BOF converter. The characterization was performed by chemical analysis (titration for iron and its oxides and Inductively Coupled Plasma Atomic Emission Spectroscopy for other elements), scanning electron microscopy, size analysis using Mastersizer 2000 equipment and X-ray diffraction. It was observed that dust is composed mainly iron in form of magnetite, metallic iron and wustite with approximately 99% of the particle size below 100 µm.IntroductionToday, steel is a important metal for the world. It can be produced for two routes, blast furnace/ basic oxygen furnace (BOF) converter and electric arc furnace (EAF) [1].First route, the iron is produced from the reduction of iron ore and coke for fuel injection and! or natural gas for a production of pig iron in blast furnace. The pig iron is sent until BOF converter to perform the blowing of oxygen to obtain the steel. In the second route, the steel is produced using scraps or direct reduced iron (DR!) using electric arc.During steel production are generated a lot of wastes like slag, sludges, scraps and dust [2]. Only in the first six months of201O, world steel production totaled 706 million tons [3]. According to Watson and Wang [4], some 10 to 20 kg of dust is generated per tonne of liquid steel produced. Thus, the reuse of these wastes can be a great to companies, because it reduces the amount of raw material to be extracted and reducing disposal costs [5,6]."

Jan 1, 2012

By Laurence G. Dyer, David G. Dixon, John Rumball, Maziar Eghbalnia, Edouard Asselin

"Linear scan voltarnmetry was used to determine the reactions that occur during the cyanidation of petzite (Ag3AuTe2). Gold oxidation in petzite requires more oxidising conditions than are required for pure gold, it also does not achieve the same current (related to reaction rate). Tellurium oxidation occurs at a similar potential in water and cyanide, but as a component of petzite is impeded somewhat in water, likely due to the stability of the precious metals. Pre-treatment of petzite to oxidise tellurium in the absence of cyanide prior to gold recovery appears to be at least moderately successful.IntroductionWhile gold occurs most prevalently in its native form, many other gold bearing phases appear throughout natural systems [I]. Tellurides are a common group of such minerals, many of which also contain silver, often existing in association with native gold deposits. The six major gold-bearing tellurides are calaverite (AuTe2), sylvanite [(Au, Ag)2Te4], montbrayite [(AuSb)zTe3], krennerite [(Au1-x, Ag,)Te2], petzite (Ag3AuTe2) and muthmannite (AuAgTe2) [2]. While several other phases exist they are much more complex (i .e. buckhornite), which dilutes and confuses the influence of each specific component. Studies of gold tellurides have predominantly focussed on calaverite as it is the simplest and most common phase, however petzite, commonly found in Australia and North America, is the focus of this investigation.Gold processing via cyanidation has been operated for more than a century and is a highly effective hydrometallurgical treatment of native gold deposits. However, some gold alloys such as tellurides have proven to be somewhat less responsive under the same conditions. Several groups have shown that gold/silver tellurides are amenable to cyanidation, but are significantly more refractory than native gold [3]. Pre-oxidation steps have been tested to remove constituents that would consume cyanide such as sulfides. Such species are also linked to the precipitation of oxidised telluriwn, forming a passive layer, further inhibiting gold recovery [2]. It is uncertain to the definite reasons underpinning the refractory nature of precious metal tellurides in conventional cyanidation."

Jan 1, 2012

By Shuqiang Guo, Gonghui Yang, Xingxing Zhang, Yuyang Bian, Song Chen, Weizhong Ding, Yinhe Liu, Lan Jiang

One of the most promising refractory materials for application is zirconia in melting superalloy. In this work, the properties and phase composition of magnesia partially stabilized zirconia ceramics (MgO-PSZ) under different sintering temperatures were systematically investigated. Commercial magnesia partially stabilized zirconia (MgO-PSZ) powders were selected as the starting materials. The magnesia partially stabilized zirconia phase composition was measured by X-ray diffraction (XRD), the density of sintered samples was tested by vacuum density instrument, the thermal expansion were obtained by thermal dilatometer from ambient temperature up to 1450°C, and the microstructures of MgO-PSZ were characterised by scanning electron microscope (SEM). The results indicated that the properties of thermal expansion, densification, microstructures and phase composition were significantly affected by sintering temperature. Densification was consistent with SEM micrographs of MgO-PSZ at different sintering temperatures.

Jan 1, 2015

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003

By K. Sarveswara Rao

The present paper firstly describes some recent trends from literature on energy management via process intensification to arrive at sustainable technologies for aqueous processing of minerals, metals and materials. Secondly, the energy saving measures practiced in leaching, solid-solution separation, solution purification, metal and material winning and environmental aspects have been discussed. The emerging importance of interdisciplinary nature of hydrometallurgy for practical applications is also highlighted. With the above background, the present paper describes an overview of energy conservation and autoclave processes with a special reference to hydrometallurgical research activities of our Laboratory.

Jan 1, 2008

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By Xiang Lan

A strain of Thiobacillus ferruuxidans No. 8 was isolated from the acidic mine water of an arsenopyrite deposit, South China. It has been found from the experimental results that the growth of bacteria was inhibited by flotation agents. The order of toxic effect of different flotation agents on the growth of Thiobacillus ferrooxidans is ethyl xanthate > butyat ammonium aerofloat > butyl xanthate ? isobutyt xauthate >? flother No. 2 oil. The bioteaching treatment of arsenic and antimony-bearing gold concentrate in Longshan mine, Hunan province, China, was influenced considerably by the presence of flotation agents. The possible causes of the influence of flotation agents were discussed and an improved method was suggested.

Jan 1, 1991

By Nourredine Menad, Christian Lucion, Maurice Save, Paul Hubaux, Solène Touzé

"The collection and treatment of WEEE has recently become mandatory in Europe and is now being organized. As the first step in current treatment processes is manual dismantling, we decided to investigate the development of an entirely automatic WEEE treatment procedure using physical separation techniques so as to limit manual sorting to the removal of hazardous components. Our approach was to test different wet and dry physical separation methods on bulk WEEE; i.e. gravity separation (jig and pneumatic table), electric conductivity separation (eddy currents), and particle shape separation (Lavodune classifier and vibrating helical conveyors). The results enabled us to determine a global treatment flowsheet of shredding, electromagnetic separation, eddy current separation, screening (2 mm), sink&float separation (d=1), and jigging. All the end products, except for the fine fraction, have possible recycling outlets. Batches of WEEE can thus be treated automatically once the problem of non-ferrous wires is resolved.IntroductionAccording to Ademe (French Agency for Environment and Energy Management; www.ademe.fr), France's annual production of WEEE is between 1.7 and 2.0 million tonnes. This waste, although of very varied composition, consists mainly of plastics and metals, and its collection and treatment has been mandatory in France since 2006; the modalities are gradually becoming organized. Existing treatment processes rely on a first step of manual dismantling which, though essential for removing dangerous components from the WEEE (e.g. batteries, cathode-ray tubes, ink cartridges, etc.), also includes separating out the decimetre-size plastic parts and metal parts. No fully automatic process has yet been developed for this type of waste. Moreover, the dismantling units in Europe are highly subsidized and call upon social workers. As this situation is not conceivable for the long-term, it is obviously important to develop entirely automatic WEEE-treatment technologies based on physical separation techniques. This would limit manual sorting to the removal of toxic components."

Jan 1, 2008

The reported values of the standard reduction potentials of the Au(NH3)2+/Au(0) and Au(S2O3)23-/Au(0) couples are reviewed to emphasise the experimental difficulties associated with the measurement of reliable values for these quantities. The standard reduction potential for Ag(I)/Ag(0) in ammonia and thiosulphate solutions measured at ionic strength 0.1 and 25oCis used to predict the following relevant stability constants () for gold complexes based on the linear free energy correlations: Au(NH3)2+2 = 1013, Au(S2O3)23-2 = 1024 and Au(NH3)43+4 = 1033. The equilibrium constant ( 10-11) for the reaction Au(S2O3)23- + 2NH3 = Au(NH3)2+ + 2S2O32- based on these stability constants is in reasonable agreement with the measured value (10-9) based on potentiometric and spectroscopic data when excess ammonia was added to a solution of Na3Au(S2O3)2. This also indicates that the stability constant of Au(NH3)2+ is 9 to11 orders of magnitude less than that of Au(S2O3)23-. Relevant species distribution and Eh-pH diagrams based on the revised data are presented.

Jan 1, 2003

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By B. C. Jena

In a chromite smelting process for the production of high-carbon ferrochromium, the slag composition profoundly affects operating conditions and the economic performance of the process. For a Canadian chromite concentrate, optimum slag composition and operating temperature were determined by process simulation with a computer model, which is based on parameters, such as the minimisation of slag volume, liquidus temperature, electrical energy consumption and chromium losses. Chromium recoveries are identified for slag compositions spanning wide concentration ranges within the quaternary system MgO-AI2O3- SiO2-CaO. The simulated data are compared with the experimental results.

Jan 1, 1994

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Xi Yun Yang

Ultrafine (0.1µm) spherical magnetite powder was prepared successfully by hydrothermal reaction of ferrous sulfate and sodium hydroxide with activated pyrite as reducing agent in the temperature range 120-140?. XRD and XPS analyses indicate that pH value and pyrite amount have a direct influence on the composition of the product. Stoichiometric Fe3O4 can be obtained only when pH value is 12 and the molar ratio of pyrite/ferrous sulfate is 1:1.8. The hysteresis loop of Fe3O4 shows a ferromagnetic behavior with a saturation magnetization of 75.2 emu/g and a coercivity of 152Oe.

Jan 1, 2006