Search Documents

By Gerhard Bayer

X-ray and thermoanalytical studies were carried out on the formation and stability of Ca-, Mg-and Mn-tungstate, and of the corresponding minerals scheelite and wolframite. The tungstates were synthesized by different methods: precipitation from solution, solid state reactions, displacement reactions with solutions and in the solid state. The reactivity of natural scheelite and wolframite with different salt solutions and in mixtures with other minerals was investigated.

Jan 1, 1989

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By Alexey T. Kovalev, Irina A. Khabarova, Valentine A. Chanturiya, Igor Zh. Bunin, Elizaveta V. Koporulina

"The paper presents new theoretical and experimental results about mechanisms of disintegration of mineral complexes and structural transformations of the sulfide surface under high-power nanosecond electromagnetic pulses (HPEMP). The heated gas outflow from nanosecond breakdown channels of sulfide minerals under HPEMP is considered. It is shown that the gas outflow from channels can be an additional destructive factor in the processes of the electric pulse discharge disintegration of mineral complexes. It is shown that the effect of HPEMP changes chemical surface composition and, respectively, technological properties of pyrrhotite and pentlandite. Morphology and elementary composition of new micro- and nanoformations on mineral surface of pentlandite and pyrrhotite have been investigated using up-to-date methods of SEM/EDX and Scanning Probe Microscopy. Preliminary electropulse effect on mineral products before flotation allows producing optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new nanophases and defects on the surface of sulfides.IntroductionThe effectiveness of High-Power Nanosecond Pulses in the disintegration and liberation of fine disseminated mineral complexes and the recovery of micro- and nanoparticles of precious metals from refractory ores was demonstrated in [1, 2]. Possible mechanisms of selective disintegration were considered in [1-3]. It has been shown both theoretically and experimentally that electric breakdowns can play an important role in the nanosecond pulsed treatment of milled minerals (e.g., semiconductor sulfides and quartz with particle sizes of 100 µm to 2-3 mm) that are carriers of finely disseminated gold and other valuable components. Electric discharges in such minerals are accompanied by a destruction of integrity in the form of breakdown channels and the formation of a system of cracks around these channels [3]. The development of the domains of induced cracks around the channels is determined by the pressure of evaporated material in the breakdown channel. Upon an instantaneous energy release in a channel (nanosecond discharges), the change in its transverse size and in the gas density and pressure in the channel is determined by (i) the radial motion of the evaporation wave, (ii) the radial expansion of the channel, and (iii) the heated gas outflow from the channel. The evaporation wave moves with a speed on the same order of magnitude as the speed of sound (or greater) and travels a distance of around the initial channel radius, i.e., a much smaller distance than the breakdown channel length."

Jan 1, 2011

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Hong Peng, James Vaughan

Thermal activation of bauxite has been proposed to enable bauxite dissolution at a reduced digestion temperature and also to reduce the organic content in the liquor. Research has been carried out on phase transformation of its main hydroxide components (gibbsite, boehmite and kaolinite) during calcination. However, there is limited information available on phase bauxite phase transformation during thermal activation. In this study, two bauxite ore samples were heated from 25 to 700 °C at a rate of 50 °C/min while monitoring the phase transformation using Rigaku in situ XRD. Different phase transformation pathways for gibbsite in the bauxite compared with pure gibbsite was observed. Boehmite and kaolinite in bauxite behaved similarly to their pure phases. The temperature of phase transformation depends to some extent on the bauxite sample. Samples were also characterised by scanning electron microscopy (SEM) to reveal changes in the microstructure.

Mar 1, 2018

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By G Hope, C Young, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing as it is refractory, increasing cyanide and oxygen consumption, and enviromnentally hazardous. Selective leaching and treatment of the arsenic would prove advantageous to conventional gold leaching methods. The reactivity of enargite samples from Montana, US and Quiruvilca, Peru were studied under alkaline conditions, pH range of 8-13, using a cyclic voltammetry corrosion cell setup. Raman spectra of the surface were taken during and after cycling to compare surface species against theoretical predominance diagrams. Under slightly oxidizing conditions, covellite (CuS) peaks were found on the surface in a short matter of time, above - 200m V vs SHE for pH 9-13, suggesting arsenic leaching, but for longer conditioning times, elemental sulfur peaks were also found, which created a passivating surface layer. By operating above pH 12, under reducing conditions, ~-500mV vs SHE, arsenic can be leached as a thioarsenate (AsS4-xOx3-), without sulfur formation.IntroductionEnviromnental limitations on pyrometallurgical processing of arsenic has pushed the desire to process enargite-, Cu3AsS4, bearing concentrates towards a hydrometallurgical solution. Attempts to process can be broken down into two categories - the co-dissolution of arsenic and copper under acidic conditions or the selective leaching of arsenic under basic conditions. The selective leaching of arsenic would preferably leave behind a chalcocite, Cu2S, or covellite, CuS, phase that would be more amenable to conventional processing methods of the copper and gold industries. These methods employ bi- or poly-sulfides to leach arsenic as Assl· [1-4], hypochlorite leaching [5-7], ammoniacal leaching [8] or fine grinding to mechanically activate the enargite surface and increase normally slow reaction kinetics[9]. This study looked into the surface formations of an enargite electrode under alkaline conditions, in a pH range from 8-13, as it cycled from -1000 mV to 1000 mV vs SHE. The understanding of the formations and under what conditions they form will be helpful in further development of any of the aforementioned processes."

Jan 1, 2012

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4T13O12 (BIT) which has a positive temperature coefficient of dielectric constant (TE) can be used to modify the negative of typical microwave dielectric ceramic BaNd2Ti4O12(BMT). However, BaNd2Ti4O12/Bi4Ti3O12/BaNd1Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C was much higher than that of Bi4Ti3O12 ceramic (around /1100°C). in this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated divided proposed to prepare ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second mop, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti1O12 ceramic pellets and spark plasma sintered at 900&apos;C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe mircoanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/B1T/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.8, a low dielectric loss of 0.0068 and a small temperature coefficient of dielectric constant v/35 ppm/C at 1 MHz.

Jan 1, 2003

By M. B. Mesina

Mechanical separation systems are widely used nowadays for scrap metal processing, but they have natural limitations in product quality. The quality of the final product is considerably improved when sensors are used in the separation process. This paper describes new methods using sensors for scrap metal sorting and quality control. An example is the electromagnetic sensor, which uses the electrical and magnetic properties of materials to distinguish between different non-ferrous metals. The measurement results of two prototypes are reported. The benefits and the possibility to integrate such systems into practical applications regarding the processing of secondary raw materials are also described.

Jan 1, 2003

By N. Choi

The distribution behavior of selenium and tellurium in nickel sulfide smelting was investigated in the temperature range of 1250-1300 °C under an inert gas atmosphere and various oxygen partial pressures. The distribution coefficients of selenium and tellurium between nickel-copper-iron matte and silica-saturated iron silicate slag were detennined in terms of matte and slag compositions, temperature, and oxygen partial pressure. The effect of slag additives such as CaO, MgO, and Ah03 on the distribution coefficients of those elements was also investigated. It was observed that the distribution coefficients of selenium and tellurium increased with increasing matte grade and temperature. The solubility of selenium and tellurium in the slag decreased with increasing the partial pressure of oxygen within the range investigated in this study. The distribution coefficients of selenium and tellurium increased with the amount of CaO and MgO. Tellurium distribution coefficients also increased by the addition of Ah03. Meanwhile, the addition of Alz03 decreased the distribution coefficients of selenium at high matte grade.

Jan 1, 1996

By Muhamad Firdaus

There is a growing interest in Magnetoelectric (ME) materials in view of both fundamental understanding and novel desirable applications. The application potential for multiferroic materials with the possibility of reversing the magnetization by applying an electric field (or vice versa) is quite promising especially in data storage application. The rare earth ortho-ferrites (REFeO3), such as NdFeO3, have been studied extensively in recent study in the context of discovery of magneto-electric (ME)/multiferroic nature materials. In this paper a potential high temperature recovery of rare earth elements in the form of REFeO3 from waste permanent magnets using direct oxidation in air was investigated. It was found that REFeO3 (NdFeO3) phase can be separated from the other oxide phases by thermal treatment of NdFeB magnet waste at 1100 °C in air atmosphere. The REFeO3 also found to have different physical characteristic (density) from the other layers and can be separated physically. This paper will include a proposed flowsheet to recover Nd as NdFeO3 through powder separation. The technique can be beneficial and favourable for RE recycling and recovery from waste permanent magnets.

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Jay. M. Khodadadi, Josef Štetina, František Kavicka

"With the aid of the proper original numerical model of solidification the instruction for preparation of input parameters for numerical simulation of technological processes, with change of the phase or structure, will be presented. A method of calculation analysis of influence of therrpophysical properties of materials entering the system of casting-mould-cores environment, and also of boundary conditions on the required simulation accuracy will be suggested. For the cast material, the influence of heat .conductivity, specific heat capacity, density and latent heat of phase transformation also has been analysed. For metallic or non-metallic moulding material"" the influence of the see main parameters has been analysed and, furthermore, their combination, influence of thermal conductivity, and of heat storage. The order of influence of all quoted parameters of a casting and moulding material was established. For example heat conductivity in the liquid state is on the last place. From the boundary conditions the -most important influence on the total solidification time and · on the mechanism of forming of temperature field has the ·boundary condition on the casting mould boundary, then follows the boundary condition on the level of a molten metal. The negligible influence has the boundary condition on the mould frame and on the bottom.IntroductionThe original and universal mathematical model of solidification, cooling and heating has been set up and checked, in order to be capable of analysing a one- to three-dimensional steady or unsteady temperature field of the casting-mould-environment system and, namely, of the system as a whole or its arbitrary parts, during any industrial technological process whose individual processes could be solidification, cooling, heating, refrigeration and others, in any sequence or singly. The model enables the simulation of traditional and also non-traditional technologies of casting in foundries, metallurgical plants, forging operations, heat treatment processes, etc. If solidification is not the matter, the metal part of the system need not be called the casting but a component, a block, a forging and the like."

Jan 1, 2000

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By Min Chen, Lei Xu

Sintering behavior and performance of high alumina refractory based on the ternary subsystem MgAl2O4-CaAl4O7-CaAl12O19 were investigated using ZrO2 as an additive up to 8 wt.% by solid state reaction sintering. It was found that the added ZrO2 could dissolve in the CA6 grains in the form of a solid solution, which enhanced the isotropic growth of CA6 grains and then improved the sintering. As a result, the densification process was improved and areas with enrichment of ZrO2 showed a more compact structure. With further increase of ZrO2 addition, tetragonal ZrO2 were found to locate in the grain boundaries for exceeding the solid solubility limit, which enhanced the thermal shock resistance, indicating that addition of ZrO2 exhibited a positive effect on sintering behavior and performance of this refractory. In addition, it is considered that the optimal amount of ZrO2 addition was about 4% considering the performance together with the cost.

Jan 1, 2015