Search Documents

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By Kathie Mcgregor, Muhamad Firdaus, Nathan A. S. Webster, Yvonne Durandet, W. John Rankin, M. Akbar Rhamdhani

There is a growing interest in recycling/recovery of rare earth elements from permanent magnets. A number of processing techniques are currently being developed but are highly sensitive to the oxidation state of the material. The oxidation microstructure of NdFeB magnets is studied at high temperatures (773-1173 K) to understand oxide formation mechanisms and support the development of viable recycling strategies.

Mar 1, 2017

By Jose F. Hevia

This study is part of a broader project on the hydrothermal conversion of copper concentrates to metallic copper by solid state reactions in which the copper remains localized in the solid phases. The kinetics of the solid/solid hydrothermal hydrogen reduction of tenorite (CuO) and cuprite (Cu,O) to metallic copper are presented. After an induction period, the process is governed initially by a nucleation step followed by rapid solid state reduction. Nucleation promoter agents decrease the induction period and control the particle morphology. Separate nucleation and reduction rate processes have been identified. Following nucleation, reduction follows a shrinking core process.

Jan 1, 1994

By Peter G. Mason

Over the last 15 years numerous Pressure Oxidation and Pressure Leach plants have been installed throughout the world. The technology is no longer regarded with awe and trepidation as plants designed to treat a wide range of feedstocks continue to be successfully brought on line. Important aspects of the design of such plants include feed preparation, slurry pumping, heating and heat recovery, pressure control and let-down, vessel design, safety and provision of associated services.

Jan 1, 1999

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By Renato G. Bautista

The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions:. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.

Jan 1, 1996

By James A. Voigt

"The efficient separation of metal species from aqueous streams by precipitation techniques requires a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems. The effects of solution chemistry, precipitator design, and solvent choice are considered.IntroductionThe application of precipitation technologies to the separation of metals from solution is widely used. Regardless of its application, be it in such diverse areas as the preparation of metal oxide powders for use in commercial products or as a unit operation in the removal of trace metals during wastewater clean up, the fundamental processes involved are the same. These processes include: nucleation from solution, either homogeneous or heterogeneous; growth from solution with chemical reaction either in solution or at the precipitate/solution interface; growth by particle agglomeration; and particle break-up by collisional or shear forces. The effectiveness of the operation and the properties of the precipitate formed, or ""quality"" of the product, are determined by the competing kinetics of the different processes. The kinetics of the processes, in tum, are determined by system-specific solution chemistries and the conditions used to carry out the precipitation operation. For example, generally, when system conditions are such that the supersaturation driving force for precipitation is very high, growth species normally do not have the time to organize themselves with a high degree of crystallographic order and the precipitate is amorphous. In this case nucleation rates are invariably extremely high and the primary mechanism for growth is the agglomeration of nuclei. Conversely, when the supersaturation levels for the same system are reduced, the kinetics of the nucleation and growth processes also are greatly reduced, and a crystalline precipitate can be formed, since the growth species have time to order on particle surfaces."

Jan 1, 1996

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By A. V. Tarasov

The proposed process is based on creating a controlled frothed layer of molten slag, in which fine particles of carbonaceous reductant and raw material to be processed are mixed with emulsified iron. Frothing of the slag layer without external blowing occurs as a result of intensive evolution of gaseous reduction products. The froth reaction process is maintained due to the heat of an electric arc in the slag layer. When the metal bath is heated by the arc to 1400- 1 500°C, the low temperature of the slag surface of about 1200-1 300°C is maintained due to low thermal conductivity of slag froth preventing heat loss. In order to maintain the required slag froth level and control the process temperature, air tuyeres are installed above the slag bath; blowing air serves also for oxidation of zinc in fumes and for its transportation. High adsorption and thermal insulating properties of slag froth ensure virtually complete elimination of dust and mist entrainment along with low heat losses. The main macrokinetic regularities of the carbon thermal reduction of zinc-containing slag melts have been studied under frothing conditions. The mechanism of formation of gas-slag emulsion has been identified under the conditions of reaction [C]+[O]=CO occurring locally at the slag-metal interface. It has been demonstrated that under the froth reduction conditions the zinc removal rate from the melt increases on the average by 3 to 5 times. Based on the physical and chemical data obtained, basic principles of the dezincing technology have been developed for different intermediate oxide iron-containing products produced in the process of ferrous and non-ferrous metals production.

Jan 1, 2002

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The climate change observed in the last decades, the increase of global warming, the melting of the polar ice caps, and the sea level rise have in common the non-sustainable development as causative agent. Different nations have mobilized joint efforts with the objectives of minimizing the impact of greenhouse gas (GHG) emissions, investing in the research and the development of new technologies in recycling, in biomaterials, environmentally friendly processes, and new fuel alternatives. This paper evaluates the efficiency of a Brazilian bentonite modified by acid attack, in the purification step of a waste oil to be used for biofuel production, that is, diesel from waste cooking oil (WCO). The following characterization test swere performed: XRD, CEC, XRF, SEM/EDS, specific surface area (BET), stereomicrography, kinematic viscosity, and spectrophotometry at 440 nm. The modified bentonite exhibited good purification capacity for WCO when compared to a commercial product.

Mar 1, 2018

By C. M. Antony

The galvanizing process involves the use of accessory equipment in a series of aggressive environments including zinc ammonium chloride flux, molten zinc at 45S°C (850°F), and acid for stripping of adherent zinc. An Fe-Ni-Cr-Co alloy has been identified which combines excellent strength and resistance to molten zinc and acid attack making it suitable for accessory equipment. The alloy was field tested by a commercial galvanizer as basket material and was found to provide improved life compared to original low-alloy steel baskets while cross-section thickness was reduced 44%. Additionally, other associated processing cost savings were realized.

Jan 1, 1992

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"We computed the optical properties of the cubic niobium nitride (o-NbN) compound using the full potential linearized augmented plane wave (FL-LAPW) method within density functional theory (DFT). The complex dielectric function and optical constants, such as optical absorption coefficient, refractive index, extinction coefficient, energy-loss spectrum, and reflectivity, are all calculated and compared with experimental results. The behavior of the computed quantities is similar to that obtained experimentally, but the optical positions are shifted to lower energies. This shift was related to the strong interband transitions, which are located at energies higher than 5 eV for NbN- as they are for IV B transition-metal mononitrides- and they appear in the computed spectra and not in the experimental spectra. These interband transitions simply shift the position of the reflectivity edge or the screened plasma frequency to the longer wavelength side.IntroductionIn recent years, NbN, as a transition metal nitride, has become a very popular material due to its high hardness, melting point, wear resistance, chemical inertness and temperature stability, which makes it suitable for use as emission cathodes in microelectronics and sensors, optical films and micro-mechanics etc [l]. Niobium nitride has long been known as highly polymorphic material, for which several crystalline structures have been reported in the literature [2]. These structures include the well known super-conducting rock-salt (Fm-3m, or Bl) structure (o-NbN), the hexagonal structure with space group p63/mmc and prototype Fe2N (18fuN), the hexagonalstructure with space group p63/mmc and prototype NiAs ~-NbN) and others.There has been a lot of computational studies for the structural and electronic properties ofNbN [3, 4-7], but according to our knowledge there is not any computational work that has been devoted to study the optical properties of this transition metal compound. At the same time a number of authors had performed experimental work in this direction. For example, Xin-kang et. al [l] studied the microstructure and optical properties of magnetron sputtered NbN thin films. Torche et. al [8] studied the composition, structure, electrical and optical properties of nonstoichiometric niobium nitrides. Newport et. al [9] investigated the reflection and transmission spectra of cubic niobium nitride films, and Tanabe et. al [10] had investigated the optical parameters and reflectivity of reactively sputtered NbN thin films by using in situ ellipsometry."

Jan 1, 2013

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Neusa Alonso-Falleiros, Aristeu Braz da Veiga, Marcelo B. Mourão, Adriano Pescarmona, Antonio Alberto Froes Schettino, Cyro Takano, Carlos A. S. Giraldo

"The Caron process of nickel extraction from lateritic ores produces a fair amount of an inert residue, the so-called “black sludge”, that is disposed in a dam according to the required environmental regulations. On the other hand, it represents an opportunity to resource recovery. This work presents the characterization of the residue, discusses some possible ways to recover the valuables, and presents experimental results of pyrometallurgical runs aimed at recover nickel as an iron-nickel alloy. It has been shown that the residue contains large amounts of silicon, iron, aluminum and magnesium, in the form of oxides and silicates, and small quantities of nickel, cooper and cobalt, besides several other elements. It has also been shown that gravimetric or magnetic concentration methods do not present promising results. On the other hand, it is possible to obtain iron-nickel alloys by high-temperature carbothermic reduction of the “black sludge”.IntroductionThe Caron process consists of a combined pyro-hydrometallurgical process to extract nickel from high iron limonitic lateritic ores, recovering also the cobalt present in the ore. The main steps are the reduction roasting of the ore, aiming at a selective reduction of nickel and cobalt to the metallic state, avoiding as much as possible iron reduction, followed by leaching with ammonium carbonate solution and the recovery of metal from the pregnant liquor [1,2]. As a result, significant amount of tailings are generated, that are disposed in appropriate dams. This residue, called “black sludge”, contains significant proportion of silica and iron, and also small amounts of nickel, cobalt, cooper and some other elements. Due to diminishing deposits of nickel ore, high metal prices and a significant amount of “black sludge “ available after several years of operation of the plant, Votorantim Metais, who operates a facility in Brazil that uses the Caron process, decided to explore the possibility of recover nickel from the residue. This paper presents the characterization of the residue, and the results of experimental work aiming recovery of nickel from it."

Jan 1, 2008

By Sutham Niyomwas

Biomorphic Cellular TiCIC ceramics were produced by vacuum-infiltrating carbon preforms with Ti02 sol and subsequent synthesis by the carbothermal reduction process. The carbon preforms used in the study were obtained by pyrolysis of parawood and neem wood. The effect of infiltration time on the composition and microstructure of the biomorphic TiCIC ceramic was analyzed by X-ray diffractometry and scanning electron microscopy. The biomorphic structure of the TiCIC ceramic is consistent with that of the biotemplate natural parawood and neem wood.

Jan 1, 2008