Search Documents

By N. Menad

The formation of the dioxins can be dependent on the quantities of carbon, hydrogen, chlorine and oxygen present in a given system, as well as on parameters such as temperature and pressure. Inadequate supply of combustion air ( incomplete oxidation ), low combustion temperatures ( incomplete combustion ), and insufficient turbulence in the combustion are factors which can favour their formation. Dioxins were produced also calatytically from chlorinated phenol precursors, non-chlorinated compounds that were chemically, and reaction of phenol with inorganic chloride. In this paper different precursors such as combination of C, H, 0, Cl, rapid formation/combustion intermediates and routes to PCDFs are reviewed, and the influence of PVC amount on the formation of these isomers is discussed.

Jan 1, 2000

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues' by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions' selectivity.

Jan 1, 1993

By SIMON TIMBILLAH

The chalcopyrite-molybdenite (Cu-Mo) flotation industry is increasingly turning to organic depressants as suitable replacements for inorganic reagents, such as NaHS, due to environmental and safety concerns as well as high consumption rates of the inorganic reagents. This presents an opportunity for improvements or design and synthesis of alternative reagents. Disodium carboxymethyl trithiocarbonate (Orfom® D8) depressant is an organic depressant with a carboxylate group on one end and a trithiocarbonate group at the other end. Fundamental results are shown regarding the interaction of the Orfom® D8 depressant in the bulk flotation of a Cu-Mo concentrate from an operating North American mine. Cyclic Voltammetry on pure copper and Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS) measurements on pure chalcopyrite with Orfom® D8 depressant treatment are also reported. Through such characterization techniques a potential adsorption mechanism of Orfom® D8 on the mineral surface was identified and its depressant characteristics in the Cu-Mo flotation systems explained.

By C. Pereira

Spent nuclear fuel (SNF) can be treated in a molten salt electro refiner for conversion into metal and mineral waste fonns for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed.

Jan 1, 1996

By Susanne Pignolet-Brandom

Fourteen samples of crushed Duluth Complex rock were characterized by the QEM?SEM automated scanning electron microscope image analysis system to evaluate the application of the system to mining waste rock characterization. The system can reliably distinguish the iron sulfides, the copper-iron sulfides and the nickel-iron sulfides. Calcite was distinguished from all other minerals except fluorite. The volumetric abundances were verified by comparing elemental abundances calculated using the QEM"SEM volumetric percentages and appropriate mineral compositions with elemental abundances determined by standard laboratory procedure. The pH and sulfate concentrations of rinse water from laboratory leach experiments correlated well with the mineralogical data.

Jan 1, 1989

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Vladimir Mindin

This paper presents results of thermodynamic investigations and experimental' studies of some essential for pyrometallurgy of sulfide concentrates topics. Among them: 1. Thermodynamic simulation and experimental investigations of roasting process, 2. Thermodynamic investigations of sulfur dioxide off-gases treatment technologies. 3. Investigations on "Mind in -Kiknadze" effect of suppression of sulfur dioxide formation during sulfide concentrates roasting in the vapor containing atmosphere. 4. Thermodynamic simulation and experimental investigations of sulfide concentrates and manganese containing materials co-roasting processes. Some essential aspects of thermodynamic simulation techniques are also discussed.

Jan 1, 1998

By Xiang (Frank) Chen, Mikhail A. Sokolov, Randy K. Nanstad

"Nickel-base Alloy 617 is being considered as a structural material for application in the secondary heat exchanger of the New Generation Nuclear Plant, a very high temperature gascooled reactor. Thermal aging of Alloy 617 plate and welds is being performed with tensile, Charpy impact, and fracture toughness tests conducted at temperatures to 950°C. Results of testing for thermal aging to 5,300 h have been obtained and are presented; varying effects of thermal aging temperature and time on fracture toughness are observed. The 9Cr-1MoV (Grade 91) ferritic steel is a candidate for structural applications in the sodium fast reactor. Fracture toughness testing of unaged Grade 91 steel has been performed to evaluate specimen size effects in preparation for future testing of the material in the thermally aged condition. Results for material in the mill-annealed and heat treated conditions are presented and show that this heat of Grade 91 steel does not indicate a small specimen bias on the fracture toughness Master Curve reference temperature.IntroductionThe behavior of advanced engineering materials will be a critical factor in the performance of Generation IV reactors. In the case of materials utilized for reactor internals and pressure vessels, the effects of irradiation and long time thermal aging are major issues. The environmental conditions for some of the Gen IV reactors are generally beyond present day reactor technology, requiring new experimental data as well as analytical predictions of expected behavior of candidate materials at conditions for which there are only sparse or no experimental data. The radiation environments and several key materials issues for some Gen IV systems are summarized in Section 5 of [l] as a starting point for modeling and microstructural analysis of Generation IV materials. More detailed descriptions of materials research and development needs and recommended activities for the SCWR, VHTR, and GFR are provided in references [2, 3, 4], respectively. Mansur, et. al. provide an interesting comparison of materials needs for Generation IV reactors to corresponding needs for fusion reactors and spallation neutron sources in [5]. The two primary candidate reactor systems currently undergoing significant research and development by the U.S. Department of Energy (DOE) are the New Generation Nuclear Plant"

Jan 1, 2012

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-9 (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 160' C for 1 h in a pressure vessel dissolved over 95 pct of the PGM from virgin catalysts and over 90 pct from used pellet catalysts. Over 85 pct of the PGM was dissolved from used monolith catalysts when a third leaching step was added. PGM concentrates as metallic powder containing over 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 250' C and used catalyst to 275" C for 1 h. The solution after heating contained primarily sodium carbonate from cyanide decomposition and less than 0.2 ppm total cyanide.

Jan 1, 1993

By E. T. White, Dean Ilievski

"The population balance is one of the basic relations for analysing particulate mineral processing operations. It is an exact relation. The principles of the population balance are reviewed and applications in the minerals industry discussed.IntroductionMathematical modelling has proved to be a very successful approach for improving the design and performance of mineral processes, particularly since the availability of computers to handle the complexity usually necessary to give a useful model.Mineral processes almost invariably involve particles, as either solid fragments, liquid drops or bubbles. Process performance usually is highly dependent on the behaviour of these particles. In modelling particle behaviour, the basic relation to be used is the population balance. This paper discusses the role of the population balance and the range of its applications in minerals processing.The Population BalanceThe population balance was developed for demographic studies, ego predicting the change in the population (numbers) of, say, school children between one census and the next. The first sustained application to the processing industries appears in the 1960s for crystallization. However it was recognised almost immediately that it had application to all particulate processing."

Jan 1, 1996

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By F. J. J. van Loo, A. A. Kodentsov, J. A. van Beek, M. R. Rijnders

"A periodic layered morphology of the reaction zone has been observed in several annealed solid/solid diffusion couples, including metal/metal and metal/ceramic couples. This morphology is characterized by a regular array of alternating layers, which are either single-phase layers or bands of particles embedded in an intermetallic matrix phase. A description of several systems showing periodic layer formation is given. It is shown that the periodic layered structure with the single phase layers and the one with the bands of particles have a different mechanism of formation.IntroductionSolid state reactions in ternary systems can produce a variety of reaction zone morphologies if there are two or more reaction products. Three types of morphology have been described in detail: 1) simple layered; 2) isolated precipitates in a singlephase layer; 3) interpenetrating columnar (lamellar) or interwoven structure. Understanding the factors that govern the formation of different morphologies is of importance in many fields of engineering. For solid state displacement reactions the conditions governing the formation of these morphologies are well understood [1-4]. For example, the development of a layered or aggregate reaction zone depends on the relative diffusivities of the components through the reaction products.This paper is concerned with the periodic layered morphology which has been observed in various solid state systems. We consider this to be a fourth type of reaction layer morphology. Two manifestations of periodic layered morphology may be distinguished. One form consists of regularly spaced layers of particles of one reaction product embedded in a matrix phase (another reaction product). The other form consists of single-phase layers embedded in a matrix phase. It will be shown that each manifestation has its own mechanism of formation. In section A we consider a system (Ag/Ti-foil/Si) in which periodic layer formation will be explained as a special case of the Liesegang phenomenon. In section B we consider systems where the periodic layered structure has a different origin."

Jan 1, 1996

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By Clemens Schmetterer, Patrick J. Masset

"The surface tension represents an important property for the modelling of high temperature processes. In this study the surface tension of two Al2O3 – CaO – SiO2 model slags and the influence of the admixture of 5 up to 30 wt.% FeO were studied. The surface tension measurements were carried out using the sessile drop technique on BN substrates under Ar atmosphere (10-6 atm O2) up to 1500 °C.IntroductionThe aim of VIRTUHCON1 is the virtualization of high temperature conversion processes, a task that requires thorough understanding of these processes. In many of these conversion processes slag plays an important role to control the properties of the product, to protect the reactor lining or simply as waste. Slag surface tension is one of the materials properties that is needed for the description of such processes, since it influences the interactions between the components in the reactor, e.g. at the slag – Fe interface in the blast furnace.Surface and interfacial tensions have thus received considerable attention in research, but the number of investigations in this particular pseudo-quaternary system is surprisingly low. Furthermore, the literature data are subject to different measurement conditions and techniques which complicates the data analysis and comparison.The slag atlas [1] offers a compilation of the available literature until 1986 (shown in Table I), but literature search has not revealed more recent studies of this system until now. For example, Elliott and Mounier [2] determined the surface tension of ACSF slags using the double tube maximum bubble pressure technique at 1200 °C. They kept their slags in contact with Cu-S-F mattes, and the slag therefore contained a certain amount of sulphur which acts as a surfactant and lowers the surface tension. The compositions of their slags were scattered over a wide composition range and they did not use a common ACS base mixture for their tests, either. The surface tension values vary between 417 and 446 mN/m, but due to the reasons just mentioned no trend in the measurements can be observed and the influence of FeO admixture on the surface tension cannot be deduced. Further information including the temperature dependence is available from Pavlov et al. [3], Ishchanov and Shushkov [4] and Murav’eva and Kaplun [5]; the diagram on page 446 in Ref. [1] has been drawn from these sources. Both positive and negative temperature coefficients are reported in these works. SiO2 is the only pure constituent that has a positive temperature coefficient [6], but a correlation of the temperature coefficient with the SiO2 content was not found to be conclusive."

Jan 1, 2011

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thermodynamics, kinetics and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thermodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thermal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003