Search Documents

By Fangtian Wang

The fully mechanized longwall mining was employed in a shallow coal seam that was under the gobs of room and pillar mining and overlain by thin bedrock and thick loose sands. Operational practices have demonstrated that severe accidents would occur including roof structure instability, roof steps, damages of shield supports, and face bumps triggered by the large area roof weighting, resulting in serious threats to the safety of underground miners and equipment. This paper uses Shigetai Mine, located in the Ordos area, Inner Mongolia, as the study site. It fully considers the geological conditions of 3-1-2 coal seam and employs theoretical analysis, 3DEC numerical simulation, and field measurements to analyze the overlying strata movement for the shallow seams under an abandoned room and pillar mine without pillar extraction. The research results serve as an excellent guide to mining in similar geological and mining conditions.

Jan 1, 2014

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

By Bruce K. Hebblewhit

Australia is well endowed with extensive reserves of thick underground coal scams, particularly in the range of 4.5m to 9m thicknesses. (For the purposes of this paper, thick scams are defined as being greater than 4.5m thick.) At the present time, the thickest, high production, high productivity underground mining operation in Australia operates at a maximum of approximately 4.8m using single pass longwall methods. In a number of instances, conventional' height operations are mining thick seam coal, effectively sterilising considerable reserves - either because of financial or technical risk concerns, or in some cases poorer quality coal at some horizons in the scam, UNSW has been involved in thick scam mining research over many years, most recently through an ACARP -funded project, jointly with the CMTE in Australia. A key part of that project involved the assessment of the relative geotechnical risks associated with the various methods under consideration. The methods were: single pass longwall; multi-slice descending longwall; soutirage and related caving methods (including the Chinese Longwall Top Coal Caving method (LTCC)): and hydraulic mining. A formal risk assessment process was adopted to review the risks, relative to a conventional 4m high longwall operation. This paper presents the findings of that risk review and discusses the geotechnical issues (and some possible solutions for risk management) which need to be dealt with in order to bring these methods to fruition in the context of the Australian coal industry environment.

Jan 1, 2001

By Vince Caggiano

The newly developed Hilti OneStep roof bolt combines the standard 5-step anchoring process (i.e. drilling, transfer of drill steel, insertion of resin, insertion of rod and tightening) into one easy operation. It also replaces 4 items (drill head and steel, adhesive cartridge and anchor) for simplified material management. This paper describes its history of development, and bolt, bolt drilling and bolt resin specifications, experimental test results in Germany where it achieved a reduction of 36-42% in roof bolt cycle time and 25-30% improvement in gateroad development rate. In the U.S. coal mines, a time study showed that OneStep can save approximately 50 seconds in installation time per bolt.

Jan 1, 2005

By Frederick Carr

1. The application of retreat longwall mining to the North American coal mining conditions is be¬coming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be the keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the col¬lapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The #3 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularly regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1982

By Bingjie Huo

"China is a major coal producer and consumer. It is necessary to mine the steeply pitching coal seams due to development of the coal industry to meet the increasing needs for coal. Flexible shield supports mining is a safe and efficient mining method for steeply pitching coal seam that was first applied in HuaiNan mining area in the 1970s. The coal seams are steeply pitching in DaAnShan Colliery, so mining is mainly done by the flexible shield supports method. The roadway lay-out and extraction technology are researched in order to improve the safety, yield and work efficiency in the flexible shield supports working face. Optimization of the flexible shield supports mining method is discussed. The main optimization aspects are as follows: (1) the angle of working face and mining track roadways are increased from 23° to 28°, and (2) the technology and parameters of coal breaking are optimized. Applicable conditions, as well as advantages and disadvantages are also discussed. Finally, a comparison is made of the two different flexible shield supports mining methods, namely ""bench blasting . technology"" and ""piecewise blasting technology"".INTRODUCTIONChina is the largest producer and consumer of coal in the world and relies heavily on coal for energy production. At present, Chinese production is about 42% of the worldwide production, and coal has accounted for 76% of primary energy production. Coal plays a dominant role in the structure of energy production and consumption, which is fuel and an important industrial raw material but it is non-renewable. In recent years, the high inclined seams (35°< angle of coal seam < 45°) and steeply pitching coal seams (angle of coal seam >45°) have drawn increasing attention in the mining sector along with the growth of coal mining. There are two reasons. First, there are abundant reserves of high inclined and steeply pitching coal seams in China, which account for 15- 20% of total reserves (Xie, Dong-hai, 2007). Highly inclined and the steeply pitching coal seams are mined in more than 50% of the western mining provinces such as Sichuan, ChongQing, YunNan, GuiZhou, XinJiang, GanSu, NingXia, etc. As the mining of mineral resources continues west in the 21st century, the study of coal mining in high inclined seams and steeply pitching coal seams will be of great importance. Secondly, better quality coal has become scarcer in the eastern mining areas after years of exploitation, so steeply pitching seam mmmg is growing more prevalent. In short, carrying out research on steeply pitching seam mining technology plays an important role in sustaining the development of the Chinese coal industry."

Jan 1, 2010

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

By Francis S. Kendorski

High-extraction mining of coal and other stratified minerals has a predictable effect on the surface and subsurface. Impacts on ground waters in overlying strata and on surface waters, that are associated with overlying sequential zones of collapse, fracturing, aquiclude, constrained strata, and surface disturbances can be anticipated. Since first quantified around 1979 in Bureau of Mines sponsored contract research work and others (and often adopted by state regulators), with zone extents based upon multiples of mined seam height of 24 to over 60 for the fractured zone, much new data have become available. In examining the sources of data and the methods and intents of the researchers of over 65 case histories, it became apparent that the strata behaviors were being confused with overlapping vertical extents reported for the fractured zones and aquiclude zones depending on whether the researcher was interested in water intrusion into the mine or in water loss from surface or ground waters. These more recent data, and critical examination of existing data, have led to the realization that the former "Aquiclude Zone" defined for its ability to prevent or minimize the intrusion of ground or surface waters into mines has another important character in increasing storage of surface and shallow ground waters in response to mining with no permanent loss of waters. This zone is here named the "Dilated Zone." The existence of the dilated zone explains the ratios of up to 60 times the mined thickness. Surface and ground waters can drain into this zone, but seldom into the mine, and can eventually be recovered through closing of dilations by mine subsidence progression away from the area, or filling of the additional void space created, or both. A revised model has been developed which accommodates the available data, by modifying the zones as follows: ? collapse and disaggregation extending 6 to 10 times the mined thickness above the panel ? continuous fracturing extending approximately 24 times the mined thickness above the panel, allowing temporary drainage of intersected surface and ground waters ? development of a zone of dilated, increased storativity, and leaky strata with little enhanced vertical permeability from 24 to 60 times the mined thickness above the panel above the continuous fracturing zone, and below the constrained or surface effects zones, whose thickness or existence is dictated by the zones above and below ? maintenance of a constrained but leaky zone above the dilated zone and below the surface effects zone, whose thickness or existence is dictated by the zones above and below ? limited surface fracturing in areas of extension extending up to 50 ft or so beneath the ground surface

Jan 1, 1993

The U.S. Bureau of Mines (USBM) has developed the coal Mine Roof Rating (CMRR) to aid in ground control. This paper describes the application of the CMRR at four coal mines operated by a major U.S. coal company. The mines are widely separated geographically, and cover a wide variety of geologic conditions and mining methods. The study found that the CMRR was a useful predictor of roof performance. In mines where the CMRR varied, and other parameters held constant, roof falls were associated with low CMRR values. Important similarities in roof performance were found in mines with similar CMRR values, despite radically different geologic environments. The analyses also indicated that statistics can be used to evaluate ground control performance. For these mines, a "roof fall probability" can be estimated from the CMRR and the intersection span. A spreadsheet program has been developed to facilitate treatment of CMRR data, and it is briefly describe

Jan 1, 1994

By Feiya Xu, Syd S. Peng

"As a highly efficient and new surveying and mapping technique, 3D laser scanning technology has been gradually applied to surface subsidence monitoring in mining areas. 3D laser scanning technology was used to monitor the mining subsidence in a coal mining area in this paper. Based on the 3D laser scanning data obtained in March, May, and December 2016 in the studying mining area, the surface subsidence basin and points deformation were acquired. The 3D laser scanning data were compared with that of the conventional surface movement surveying method. The results show that the 3D laser scanning technology could obtain the data of the subsidence basin more efficiently and reflect the true shape of surface subsidence caused by mining. The maximum surface subsidence obtained by 3D laser scanning technology was 3.60m, while the conventional surface movement surveying was 3.56m; the relative observation error between 3D laser scanner and the conventional surface movement surveying was less than 10%. Therefore, it is feasible to apply 3D laser scanning technology to monitor surface subsidence in coal mines.INTRODUCTIONWith the over-exploitation of coal resources, the problem of surface subsidence has become the focus of attention (Peng, 2011; Guo Wenbing, 2012). Setting up observation stations for surface movement was the traditional method to study the characteristic of surface subsidence and its parameters. At present, hundreds of observation stations have been set up in longwall mining, and a large number of measured data have been obtained (Ministry, 2017). However, due to the length of time surveying requires, great workload in the field, the high cost of observation, and difficult protection for monitoring points, conventional observation stations for surface movement have not met the research on surface subsidence. Therefore, as a new surveying and mapping technique, 3D laser scanning technology has been gradually used for surface subsidence monitoring in mining areas (Ma Liguang, 2005). Li Qiu, Qin Yongzhi, and Li Hong (2006) first proposed 3D laser scanning technology in the application of monitoring surface subsidence in 2006. It was showed that the 3D laser scanning technology had obvious advantages in efficiency and accuracy of data acquisition than other methods of deformation monitoring technology of surface subsidence (such as total station, precision level technique, GPS, etc.). Subsequently, Zhang Shu, Wu Kan, and Wang Xiang (2008) and Chen Ranli and Wu Kan (2012) analyzed the feasibility and precision of 3D laser scanning in subsidence monitoring, concluding that the 3D laser scanning can be used to obtain the subsidence basin and the monitoring precision can reach millimeter. Hu Dahe, Wu Kan, and Chen Ranli (2013) introduced the data processing method of 3D laser scanning for surface subsidence in detail. On the basis of a case study, the subsidence basin in subsidence area was obtained, which reflected the shape of mining subsidence basin intuitively and comprehensively. Wang Qisheng, Wu Kan, and Zheng Ruyu (2010) carried out the research on prediction parameters of mining subsidence by using 3D laser scanning data and got the parameters of major influence angle and the offset distance of inflection point. Meng Wanli, Cai Lailiang, and Yang Wangshan. (2017) made a profile analysis for the 3D view of the surface subsidence using 3D laser scanning data and put forward a “Geomagic” method of surface subsidence prediction."

Jan 1, 2018

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Keith A. Heasley, Christopher R. Newman

"Originally developed in 1993, LaModel has aided mining engineers and researchers alike in improving the design and safety of underground single- and multiple-seam mining operations (Heasley, 1998). Through the years (Heasley, 2011), the use and capabilities of the LaModel program have grown immensely while adapting to ground control concerns and problems within the mining industry. Presently, MSHA specifically mentions the use of LaModel for the analysis of, “complex non-typical roof control plans,” defined as either room-and-pillar retreat mining greater than 1000 feet, bump- or bounce-prone mines, or other criteria considered unusual by the District Manager (Stricklin, 2013).With an ever increasing number of users and an increase in available solution options and complex analyses, there is now a significant demand for better education and training in the practical application and detailed analysis using LaModel. This paper presents the development of an electronic user’s manual and comprehensive online training course created in an open online learning environment in order to better inform and train industry professionals as well as engineering students and new users. The development of both the user’s manual and online training course will ultimately increase the ground control design effectiveness of mining engineers, leading to safer and more productive mine designs.INTRODUCTIONOver the past 20 years, mining engineers and researchers have used the LaModel program for improving the design and safety of single- and multiple-seam mining operations. LaModel uses a laminated, displacement-discontinuity, boundary-element method which simplifies the overburden into a stack of frictionless homogeneous laminations and limits the detailed analysis to the seam itself. This approach is fundamentally simpler than either finite-element, finite-difference, or discrete-element approaches; and, therefore, the program provides a significant reduction in computational time and efficiently calculates the displacements, stresses, pillar safety factors, multiple-seam interactions, subsidence, etc. for thin-bedded deposits such as coal, salt, potash, limestone, etc. (Heasley and Salamon, 1996; Heasley and Agioutantis, 2001). The laminated overburden model in LaModel is different than previous homogeneous elastic formulations and more realistically represents the natural flexibilities of the stratified sedimentary overburden typically associated with coal seams (Heasley, 2008)."

Jan 1, 2015