Search Documents

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Robert P. Kudlawiec

The use of Mobile Roof Supports (MRS) in pillar retreat mining has been a fairly recent occurrence in coal mining operations in the United States (1988). Determining the pillar block configuration, the crosscut and entry centers, the number of entries developed, the method of ventilation, and the type and mixture of equipment used arc all factors in establishing a successful pillar retreat operation. This paper will evaluate and report on the history of one coal company's relationship with MRS usage for pillar retreat mining and focus on the company's use of horizontal pillars (inverted-blocks) for the panel configuration.

Jan 1, 2000

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By S. F. Smith

Following a roof beam collapse on a major production district at the British Steel Corporation's Dragonby Iron Ore Mine, Scunthorpe, South Humberside, UK, rock mechanics investigations were undertaken in this room and pillar operation to assess the stability of workings throughout all the underground mine area. Over a four year period room convergence and roof sag were monitored in different mining areas and various junction configurations in order to assess and compare the relative movement of the strata resulting from mining activities, where varying rock bolt lengths and patterns have been utilised. The paper, after shortly describing geological aspects and mining methods, presents the research procedure adopted together with the instrumentation employed and discusses the results obtained during these investigations.

Jan 1, 1995

By Long Fan, Shimin Liu, Guijie Sang

"Weak shale roof falls have long been the main cause for fatalities in underground coal mines. Moisture-induced swelling is one of the root causes for the degradation of roof shales. In this study, slake durability tests are conducted on shale samples collected from Illinois basin coal mines, and different levels of durability are analyzed according to Gamble slake durability classification. There are two main mechanisms influencing the shape of retained fragments after two cycles of wetting and drying: mechanical abrasion and swelling pressure. A prototype optically based shale swelling apparatus is designed and manufactured for the shale free-swelling measurement. The experimental results suggest that swelling pressure tends to deteriorate shale laminations. Moisture-induced swelling of the No. 6 roof shale from Bear Run Mine was measured under 100% relative humidity condition. The measured swelling strain normal to beddings is ~5 to 7 times greater than the swelling strain parallel to beddings. This suggests that interlayer expansion plays a key role in moisture-induced swelling. Cracks induced by swelling pressure tend to occur along the bedding plane and lead to shale deterioration. INTRODUCTION Background Ground falls have long been the cause for nearly 50% of all fatalities in underground coal mines and continue to be one of the greatest safety hazards in underground spaces. Among the various ground fall hazards, roof failure takes up 23% of total fatalities in underground coal mines, of which 13% are due to skin failure and 10% are due to massive roof falls (Mark, Pappas, and Barczak, 2011). Roof failures associated with weak shales are summarized in previous studies (Molinda and Mark, 2010; Aughenbaugh and Bruzewski, 1973; Bajpayee, Pappas, and Ellenberger, 2014; Murphy, 2016). For mine roof instability and failure, two aspects can explain the failure mechanism of weak roofs. One is the elevated stress concentration in lateral direction due to the mining-induced excavation and its stress redistribution around the mine opening (Song and Stankus, 1997; Fan and Liu, 2017; Hill, 1986). The other mechanism is the passive stress-relief due to the strength weakening induced by the ambient moisture and temperature fluctuations during a period of time. Shale is moisture sensitive and presents a lower durability if it is exposed to a highly humid environment for a long time, thus leading to roof deterioration and instability in underground coal mines (Aughenbaugh and Bruzewski, 1976; Stateham and Radcliffe, 1978; Chugh and Missavage, 1981; Klemetti, Oyler, and Molinda, 2009). It is well known that shale is a clay-bearing sedimentary rock and that clay minerals are water sensitive. The moisture uptake for shale will induce the micro-deformation of a shale matrix, thus the structure and strength of shale is a function of time and intensity of moisture exposure. All mine engineers notice moisture-induced shale deterioration; however, the underlying mechanism(s) are still not fully understood due to the complexity of geophysical-chemical water-shale interactions (Huang, Aughenbaugh, and Rockaway, 1986; Hensen and Smit, 2002; Diaz-Perez, Cortés-Monroy, and Roegiers, 2007). The coal mining industry is still in the process of finding a technically sound, cost-effective technology to prevent this unexpected and unpredictable shale roof failure. Therefore, understanding how the moisture-sensitive shale responses to various ambient moisture and what role exposure duration plays in shale roof failure is key to prevent unexpected roof incidents, which will lay the foundation for the long-term roof support design and ground control management."

Jan 1, 2017

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Anthony T. Iannacchione

The Solar No. 7 and Solar No. 10 mines were designed to prevent mine waters from directly discharging to the surface. In January of 2004, a discharge occurred as the Solar No. 7 mine was in its final stage of flooding through a barrier averaging 456-ft in width over a 1,600-ft length (No. 1). Another barrier (No. 2) was designed to protect four municipal water wells operating 1,800- ft away and producing from within or slightly below the Upper Kittanning coalbed from the adjacent Solar No. 7 and No. 10 mine pools. These two barriers were selected for this study because of varied mine layouts, mining methods, and geology factors affecting their performance. Analysis was aided by the collection and georeferencing of 6-month mining maps from the Pennsylvania Department of Environmental Protection (PA DEP). A structure contour map of the Upper Kittanning coalbed was constructed from mine map elevation points. These data and 2-ft surface contour maps were used to measure the precise location of the coal outcrop. The actual discharge point was as little as 425-ft away from a thinpillar section and 475-ft away from a pillar recovery section. The discharge point was found to be located slightly above the coal, indicating that the drainage path was at least partially through the strata directly above the Upper Kittanning coalbed. Hydraulic conductivities and potential discharge pathways are analyzed and discussed. The possible factors influencing the performance of the down-dip barriers at Solar No. 7 and Solar No. 10 are: a) the width of the barrier, b) the applied hydraulic gradient, c) the type of mining adjacent to the barrier, d) the overburden, e) the pattern and characteristics of fractures, and f) the quality of waters contained within the mine pools. This study, part of a larger effort funded by the Appalachian Research Initiative for Environmental Sciences (ARIES), is tasked to determine the key factors responsible for the successful design of down-dip coal barriers.

Jan 1, 2013

By Behdeen Oraee

Constructing tunnels underground is generally described as a high-risk activity because conditions in the surrounding area tend to be unpredictable. This would and can create unique dangers in every situation. It is important to gain a deep understanding of the risks associated with tunneling in order to reduce the likelihood of their occurrence and severity of their consequences should they occur. For this to be achieved, different risks should first be evaluated and ranked according to their relative importance and criticality. The Amir Kabir tunnel is considered one of the most dangerous tunnels in Tehran, Iran, in terms of the risks involved in its excavation and their potential consequences. In particular, part T4 of the tunnel passes through a zone of different strata and also a compound of various soils. This paper studies part T4 of the Amir Kabir tunnel from a risk analysis and risk management point of view. In doing so, factors increasing total cost, causing delay in the project completion time, decreasing the operation rate and downgrading project quality were identified and ranked according to their importance using the aggregate primary index risk method. For this purpose, a comprehensive questionnaire was designed and completed by tunneling experts. By responding to the questionnaires, the experts determined the relative likelihood of occurrence of the studied factors and their potential consequences. As a result, the experts suggested several alternatives to reduce the risks involved in this particular study. Moreover, the experts completed new questionnaires whilst taking into account different alternatives. In the next step, the risks before and after applying the alternatives were compared. As a result of performing the said analyses, it was concluded first that the aggregate primary index risk is an effective tool in identifying the risks involved in such projects. Second, it was concluded that, by taking into account different alternatives when analyzing and ranking the risks, severity of the said risks can potentially be reduced. Also, by considering such matters when analyzing tunneling risks, the projects? efficiency can greatly increase as a result of reducing risks that threaten financial and human resources. The approach introduced in this paper, together with the methodology described, can be adopted by the mining design engineer in all similar situations. They will be of particular advantage in such methods as room and pillar mining, where the number of similar tunnels required is high.

Jan 1, 2014

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002