Search Documents

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

One of the most important parameters in rock/resin/bolt load transfer mechanism is the surface property of the bolt. Although there are various bolt surface configurations available in the market, very little work is reported on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness conditions which is considered as being a realistic way of evaluating bolt surface roughness. A series of shear tests have been conducted on the flattened bolt surface to study the shear behaviour of bolt/resin interface. Based on the experimental results, a mathematical model has been developed to predict the shear resistance of the bolt/resin interface at various normal stress levels for the bolt types used in the study.

Jan 1, 1999

By Satyendra K. Singh

If the extraction is beneath massive roof strata, the roof tends to 'bridge' across large spans without failing, the caving behaviour is complex and irregular. Understandably, these give rise to many geotechnical problems with safety implications and involving sometime huge direct and indirect costs. Only two important problems, 'feather-edging' in pillar mining and `severe periodic weighting' in longwalling, are discussed in this paper in the background of geomechanics investigations in Australia at Blue Mountain Colliery and in South Bulga Colliery respectively. `Feather edging'- a major source of injury and fatal accidents in Australia and South Africa in such situations, refers to a phenomenon where the roof, at the goat edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. The results of the first comprehensive, monitored trial in an Australian pillar extraction coal mine, suggests how the roof falls into feather-edging caving (generally) because of multiple shear-planes (interpreted) and how it may be alleviated. Because of complex fracturing behaviour of massive roof strata, periodic weighting at a longwall face is certain to manifest itself as 'yielding supports', heavy conditions', rapid convergence and in the worst case, as a cause of face stoppage. After briefly discussing the programme of instrumentation (in a chain-pillar and over the would-be goal) and results, this paper attempts to improve mechanistic understanding of the related geotechnical issues associated with the weighting behaviour and aims at establishing a 'threshold' value of weighting severity index (suggesting intensity of periodic weighting) with an objective to optimise operational controls before mining through potential (future) weighting areas.

Jan 1, 2000

By R. Fraher

Hazard analysis utilizes interaction mechanisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi-seam mining, such as innerburden thickness, geology and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor conditions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential damage from interaction.

Jan 1, 1992

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

Numerical simulation for microseismicity due to mining at one of the collieries in Australia was carried out and the results were compared to the observed microscismicity. 3-D Stress analysis showed stress concentration on the edges of the mined areas and on the coal pillars- The stress concentration ahead of the coal face was biased to the tailgate. This is similar to the observed distribution of microseismic events. Stress reduction above and below the mined area was seen. Tensile stress was observed mainly above the mined area. It was realized that compressive failure due to nearly vertical maximum principal stress and nearly horizontal minimum principal stress in retreat direction (NS) might occur ahead of the face. Tensile failure due to nearly vertical minimum principal stress above the mined area was expected. Compressive failure due to nearly horizontal maximum principal stress in EW direction and nearly vertical minimum principal stress above and below the mined area were also expected.

Jan 1, 2001

By G. Herget

To improve quality control of roof conditions, a program was carried out at Elliot Lake uranium nines in Ontario, Canada to test a portable TV camera system. This camera has a 29 mm diameter probe and is capable of identifying crock locations, crack width and approximate dip direction. The extent of fractures to the roof was checked with the aid of a vacuum system by placing packers in various boreholes and checking for communication. The removal of some rock bolts indicated an increase in fracture extent.

Jan 1, 1982

By Robert M. Cox

The successful application of the science of rock mechanics to the practical problems of coal mine design requires the acquisition and reduction to useable form of large amounts of field and laboratory data, and the construction and analyses of numerous geostructural models containing a wide variety of geometric and physical strength variables. Typically, the rime constraints placed on a new mine design project coupled with the inherent complexities of a good rock mechanics study combine to limit the applications of rock mechanics to the most rudimentary level. To facilitate a better application of rock mechanics to mine design problems, an interactive software package has been developed for use on a graphic mini-computer system that serves to aid the engineer in the timely and efficient analyses of rock mechanics data and geostructural models. The first phase of the rock mechanics package solicits the input of the raw geologic and rock strength data, analyzes and arranges this data in a logical manner, produces complete listings and statisitical summaries of the various rock properties, and stores the data on magnetic tapes and disks to serve as a future Rock Mechanics Data Base. The second phase of the software package provides for the analyses of a variety of geostructural models using a wide variety of geometric variables coupled with the rock strength data stored in the Rock Mechanics Data Base. This software package allows for the evaluation of numerous geostructural mine models for the design and selection of mine roof support and pillar systems (see Table l).

Jan 1, 1982

By E. Yasar

This paper describes the use of the sand and plaster physical modelling technique to investigate the deformation around mine roadways using a variety of support methods in a particular form of stress field. The characteristics and conditions of coal measures rock were considered prior to the preparation of the models and the insertion of support The investigation has clearly shown how floor lift, roof failure and sidewall movements of mine roadways in laminated weak rock conditions gradually develops as a result of the increase in the stress and, also, how it is related to the level of support used.

Jan 1, 1995

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By J. R. Stoltz

To date, there has been limited formal research dealing with the use of Mobile Roof Supports (MRS) for pillar recovery. This paper, which is a portion of a larger project, presents convergence data from 4 different mine case studies. MULSIM was used to create a numerical model. The resulting information from this model was then compared to the actual measured values. MULSIM was also employed to analyze the industry-accepted pillar/barrier layout for mining underground reserves with the Joy Highwall Mining System. This layout was examined for both a low cover and a high cover extreme,

Jan 1, 1999

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

By P. Oliver

Rockburst conditions were first encountered at Inco's Sudbury area operations in the mid 1930's when mining advanced to below the 610 m (2000 ft.) horizon. Now, mining is being carried out at depths down to 2130 m (7000 ft.) at Inco'a Creighton Mine. While rockburst potentials have increased with depth. improvements in mine planning, methods, support systems and developments in destressing have alleviated the condition to where it is less of a problem now than it was in the early years. Hang of the improvements were developed, of necessity. through observation and reasoning because these were the only tools available at the time. Now, we are making use of stress - measurements, numerical modelling and microseismic source location technology to - help further reduce rockburat hazards.

Jan 1, 1987

By John M. Karhnak

The Bureau of Mines has a long history of research in Ground Control. For many years, this work was done at Bureau facilities by Bureau researchers. As the tiles changed, however, the area of research interest broadened, and additional methods of implementation, such as con- tracts, were added. 'Ibis paper outlines the organization, goals, and methods of implementation of the Bureau Ground Control Program, along with procedures for project selection. This program organization is followed by several specific examples of Bureau research that will be soon ready for use in the mines.

Jan 1, 1981

By Alan Bugden

Goedehoop colliery in South Africa has experienced a number of substantial roof falls in roadways and intersections. Many of these have been associated with geological slips and/or horizontal compressive stresses. This paper describes a numerical modelling study conducted after one such fall with the objective of clarifying the roof failure mechanism associated with these falls. The fall was located at an intersection and occurred as the last cut was being made to complete the intersection. One bounding surface of the fall was formed by the geological slip; the others were formed by fresh failure surfaces. The fall took place despite the slip being identified as a hazard and additional bolts being placed by the workforce. In conjunction with the modelling work tests were conducted on samples from the roof in which the fall occurred, these gave a U.C.S. of 80 -100MPa. Several in-situ stress tests had already been conducted at the mine; a further test was conducted close to the fall site. The tests show that the largest stresses are horizontal. However, the maximum stresses of 6-12MPa are small compared to the compressive strength of the root. Computer modelling highlighted a mechanism arising from the conjunction of a geological slip and horizontal compressive stresses that could result in tensile failure of the roof leading to the fall. Sensitivity studies were conducted to identify risk factors associated with this mechanism and the modelling results used to assist in formulating a support strategy to combat falls of this nature.

Jan 1, 2003

By Murali Gadde

Among different types of ground control problems associated with underground coal mining, those related to in situ stresses are the most common ones affecting the safety and economy of a mining operation. As a result, this has been the focus of many ground control research works done in the last three decades. This paper summarizes a recent work done on in situ stress related ground control issues of underground coal mine development workings. The approach used in this study was three¬-dimensional finite element modeling by an implicit code, ABAQUS/Standard. In the models, roof stability evaluations were made using Hoek-Brown rock mass failure criterion. Influence of the in situ maximum horizontal stress angle on the stability of both entry and intersection was examined to help determine the best development layout orientation. Also, the effect of in situ stress ratios on the stability of development openings was studied. To make the work more general, both 'low' and 'high' in situ stress fields were considered In general, the modeling results indicated that entries oriented in the direction of maximum horizontal stress were in the best condition while those oriented at 90° had the least stability. For intersections, the maximum and the minimum stability were seen at 0°/90° and 45°, respectively. However, under some combinations of input conditions, the best or the worst conditions were noticed at same other orientations as well. Based on these findings, layout design charts were prepared for both entries and intersections. It was also found that the change in ground conditions with change in layout orientation was more significant for 'low' in situ stress fields than for the higher ones. Change in the average safety factor with change in the ratio of in situ maximum horizontal to vertical stress resembled a lognormal distribution curve. However, the effect of the ratio of in situ maximum to minimum horizontal stress lacked such a clear trend for different input combinations considered.

Jan 1, 2004

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By Yunqing Zhang

Weak shales refer to those with lower strength, thinly- laminated structure, sensitivity to moisture and weathering as well as significant time dependent behavior. It has been said that many future coal reserves with good quality have weak immediate roofs. Therefore their geo-mechanical properties and behavior must be known before an appropriate support plan can be designed. In this study, four types of shales collected from underground coal mines were tested in the laboratory. Their modes of failures in underground were observed and correlated with their lab behavior. The failure mechanisms of thinly-laminated weak shales were analyzed by the means of numerical modeling.

Jan 1, 2004

By Susan Robertson

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100% can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

Jan 1, 2002

By Deno Pappas

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state¬of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-terra underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH's Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results from an extensive series of Schmidt Hammer tests found that the shoterete increased in strength by 70% during the humid summer months.

Jan 1, 2002