Search Documents

By W. M. Ma, W. L. Zhong, Syd S. Peng

In a longwall section that consisted of 7 longwall panels, there were two high pressure gas transmission pipelines across the panels burying from 3 to 10 ft. below the surface. One pipeline was 20 in. in diameter while the other was 24 in. in diameter. In order to investigate the stress conditions sustained by the pipelines during underground longwall mining, strain gages were mounted on the pipelines above panel #3, #4, and #5. Survey monuments were also installed along but near the pipelines. This paper presents a subsidence prediction method and the preliminary results of the pipelines' stress conditions as affected by underground longwall mining.

Jan 1, 1986

By Richard W. Kimball, Fred B. Estep, Dwayne E. Easterling

This paper discusses the overall challenges to construct a 15,125.7 m (49,625 LF),wastewater drainage tunnel in Cobb County, Georgia by a joint venture of Gilbert Southern Corp. and S.A. Healy Co. and a construction manager Parsons, with Jacobs Associates as a subcontractor. The goal of the project is to provide wastewater retention during peak usage and is connected to a treatment facility near the Chattahoochee River. The primary component of the project is the TBM-driven hard rock tunnel. Additional works include drill and blast areas; four intake interceptors, two construction shafts and a 33.5 m (110 ft), diameter pump station shaft.

Jan 1, 2003

By David V. Fitterman, David L. Campbell

We've used direct current resistivity (DC), electromagnetic (EM), induced polarization (IP), and ground-penetrating radar (GPR) geoelectrical methods to study mine dumps. The results reflect lithology, pore water saturation, and dissolved solids in the pore water. If the pore water has a pH less than 5, conductivity maps can indicate acid generating potential. IP measurements can help distinguish mineralogy in mine dumps, especially concentrations of sulfide minerals. EM and DC can help locate acidic/high TDS groundwater associated with mine dumps. GPR methods failed at the sites we studied in the West. Our own conclusions are augmented by those from the recent literature.

Jan 1, 2000

By Peter J. Conroy

Introduction Most subsidence monitoring to date has been surface monitoring to develop empirical relationships of the magnitude and extent of subsidence effects. Federal regulations are forcing a better understanding of subsidence. Empirical methods of subsidence prediction may not be adequate, since the empirical relationships may not be valid between or even within coal fields. A better understanding of the mechanics of subsidence is required in order to develop and verify analytical models. This paper presents some of the results of surface and underground monitoring in longwall faces of a coal mine. The seam thickness in these mines ranges from 5 feet to 6 feet at depths of 600 to 1100 feet.

Jan 1, 1982

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By Francis S. Kendorski

INTRODUCTION Caving offers the lowest cost per ton of any large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently taken on new importance as deeper lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface min¬ing methods, and too low grade to support any type of underground mining except a bulk method such as caving. Announced discoveries or indications that may be amenable to caving include: Climax's Mt. Emmons molybdenum discovery in Colorado; Molycorp's Goat Hill molybdenum prospect in New Mexico; the Phelps Dodge molybdenum deposit in Beaver County, UT; Arizona copper occurrences such as Asarco's Sacaton, Hanna's Casa Grande, Noranda's Lakeshore, and Ken¬necott's Safford; Anaconda's suspected deep copper de¬posit in Butte, MT; Anaconda's Carr Fork, UT, deposit; and perhaps others. CAVABILITY'S ROLE IN FEASIBILITY STUDIES Caving is a system of underground mining which removes support from underneath an ore body. As a result, the rock mass fractures, fails, and flows vertically downward by gravity to be collected in previously ex¬cavated funnels. Types of ore that have been mined by caving include molybdenum, copper, iron, nickel, as¬bestos, and diamonds (Julin and Tobie, 1973). It is primarily a large-scale method, with production rates of more than 45 300 t/d (50,000 stpd) having been achieved. However, the initial capital investment before return is very high, often in the hundreds of millions of dollars. The cavability of an ore body or mineral occurrence is a critical item in the feasibility study of a proposed mine, not only from the point of overall minability, but from the point of impact on other costs such as blasting, loading, hauling, crushing, and grade recovered. Aside from the often-asked question of, "Will it or will it not cave?" the real questions are, "Can we afford to make it cave, carry the rock away, and extract the mineral?" The last is not a topic of this chapter, but the first two are. The cavability of an ore deposit or mineral occur¬rence is based on many things, but clearly, if a large enough area is undermined, any rock mass will cave. The result could be a violent collapse as occurred at Urad, CO (Kendrick, 1970), or perhaps the rock mass will cave beyond the ore boundary. Another unfavor¬able result could be ore blocks that are too large for the equipment and orepasses to handle without considerable secondary blasting. Weak rock with numerous fractures may produce a very fine ore when it caves, resulting in dilution and ground control problems. DETERMINING STRUCTURAL DOMAINS It has long been recognized that the geologic nature of an ore body is important to cavability (King, 1946). Such items as weak rock material, intensity of fractur¬ing, and severity of faulting all contribute to the success of a caving operation, and information regarding these is required as a minimum for the cavability determination. In practice, the rock mass-defined as the blocks of intact rock together with the intervening fractures, joints, faults, bedding planes, and other discontinuities-that contains the ore body, as well as the surrounding and overlying rock, must be examined in a systematic and detailed fashion. Surficial geology maps must be pre¬pared, exploration holes drilled, and core logged for en¬gineering information. The fracturing of the rock mass must be studied to ascertain the three-dimensional dis¬tribution of fractures and their characteristics, and faults must be located and described. The strength and other mechanical properties of the rock material, the fracture surfaces, and the fault filling materials must be tested and reported for later use by designers and planners. With this basic information and an understanding of the geologic setting, the rock mass can be divided into one or more structural domains which tend to behave similarly in response to engineering activities (Robertson and Piteau, 1970). One must keep in mind that the determination of the structural domains goes beyond the geologic units present. Several lithologic units may be lumped together, while a single lithologic unit can be divided into multiple domains. Major faults often form their own domain, and the direction of engineering ac¬tivity-for example, cave advance to the north rather than the south-may alter rock mass behavior, resulting in different domains. As an example of the detailed rock fracture map¬ping required for such studies, the structural domain determinations at the Climax mine (Kendorski, 1973) are shown in Fig. 1. The circles are Schmidt equal area projections of the three-dimensional attitudes of frac¬tures (Ramsay, 1967) mapped in detail at various rock exposures. The attitude of fractures is important to the cavability determination since it dictates the directional behavior of the rock mass as it fails, and determines the effectiveness of arching, keying, and rock block inter¬locking. Low-angle fractures must be present to allow movement of the rock in the vertical direction during undermining (Mahtab and Dixon, 1976); if low-angle planes of weakness are absent, the rock mass may arch with a keystone effect, rather than moving vertically downward.

Jan 1, 1982

By Patricia Petty

If enthusiasm is a requirement, the coordinator of the Total Concept program is a dynamic, exciting leader with a lot of potential to keep the program a vital and progressive effort for many years. Art Meyer is entering his third year as the leader of the Total Concept. He is using his years of experience in the industry to emphasize the basics required for the course, and has also instituted new programs. Meyer began his career, after graduation from CSM as geological engineer in 1950, with St. Joe Lead. He held other responsible positions with Amax and Rocky Mountain Energy. He can answer any questions that may crop up or find the right resource person for those questions. Additions to the 18-year-old curriculum instituted since Meyer became coordinator are the study of industrial minerals and strategic minerals. The industrial minerals portion of the course includes visits to a major sand and gravel operation, in addition to lectures on the subject. Much of the strategic minerals requires study and lectures, since Colorado is not a big production state in these commodities. How does the director arrive at new additions or deletions to the program? "It's very simple," he says. "We listen to questions posed by the students, recommendations by industry people who know what is important, and feed-back from course alumni." Alumni feedback from this course has been extremely gratifying, according to Meyer. Other ideas are constantly surfacing, ideas that will be implemented as time and resources permit. One of the most gratifying results of the Total Concept program from an alumnus was the development of a complete teacher and student package by John Christiansen, a teacher at Cherry Creek High School near Denver. The course so excited Christiansen that he envi¬sioned an energy and minerals course to fill a perceived gap in science education on the high school level. The draft package was so attractive that it was sponsored and the publication costs guaranteed by the Society of Mining Engineers. Today, under the leadership of the Mineral Information Institute, the package is in use in several states and has gained enthusiastic acceptance. Other alumni have launched their efforts to broaden the scope of the existing science education by instituting courses or special seminars. One recent alumnus, Dick Will, class of 1984, who was sponsored by the Denver Mining Club, is conducting a science seminar based on his experiences with the Total Concept program. Meyer will be speaking at this seminar, as well as other industry speakers from the SME GEM Committee Speaker's Bureau. Jane Dianich, another alumna, brought her students at Kent Country Day school, also near Denver, into the mainstream of resource education by taking them on abbreviated field trips similar to those she experienced while in the program. She also has been a vocal supporter of the organization and available to speak to other teachers on the value of the experience. George Wright, of the Lake School and a second sponsoree of the Denver Mining Club, admits he came into the program because the six credit hours given toward his continuing education requirement were attractive. He then stayed on to become an ardent advocate of the mining industry. In his own words, "I'm a convert." Wright has developed a slide presentation and has lectured to teachers and students as well as presenting his views to the Denver Mining Club. He has also indicated a willingness to participate with other organizations who need speakers. The value of these speakers and teachers is obvious, according to Meyer. "They represent a respected segment of the public and are not too `tainted' by association with an industry that is too often under criticism from various groups. They represent, in effect, a citizen's advocacy of the industry, which is an invaluable asset to us all." One of Meyer's concerns about the program is that the out-of-state student rate attendance is declining. He is hoping that more AIME sections around the country will become involved in the scholarship program of the Total Concept. Total cost is about $1200 per student. "The rewards to their sections could be tremendous, with the same kind of participation we get here with speakers, citizen advocates, and interested persons," he said. Teachers say that the course improves their teaching and knowledge in a number of subjects including biology, history, economics, career planning, environmental data, science, math, geography, physics, and chemistry. The recent interest in hazardous waste management has sharpened the desire to learn more about this. And Meyer foresees another segment of the course to emphasize this subject. "One of the most valuable resources we have is the field trip program. The course would probably be meaningless without this opportunity to get out into the field where these folks can see what actually happens. George Wright, for example, was amazed at the very small amount of area actually involved in the mining operation - something contrary to what he had heard in the past." The 45 students are taken by van on eight trips, one each week, and the long trip to Colorado's Western Slope. During this long adventure, the students visit underground mines, including CSM's Edgar, open-cut and underground coal mines, precious metals mines, and oil shale properties. They also have opportunities to meet with mine personnel at each of these stops. These field trips fill another function. Living together and exchanging ideas helps the teachers come up with new concepts for the classroom work - expanding their horizons. "As long as we have a mining industry, this effort will continue to grow," Meyer said, "and will fulfill a need within the public education and public relations area of the industry. We need the support. I have dozens of comments from teachers who attest to the value of this program. They understand. The mining industry must continue to do its part."

Jan 3, 1986

By D. M. Larsen, N. D. King

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338°F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1994

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

What is your assessment of the current state of the minerals industry? It is no understatement that domestic mining is facing a severe crisis at this time. The sharp decline in commodity prices and demand is putting a great strain on domestic and worldwide mining, causing major declines in profits and market capital of mining companies. This, in turn, has lead to major production cuts, layoffs, shut-downs of operating properties, and the deferral of new and expansion projects. These changes in the minerals industry have played a major role in the health of the economy. Operationally, the industry continues to develop new technologies that are making our work more efficient, more cost effective and more environmentally acceptable and safe. During downturns like this, companies generally pay closer attention to operational efficiencies and process optimization. Historically, new technologies and processes tend to be developed during down markets, and I believe we will see the same thing as companies strive to preserve liquidity and maintain or improve their margins. On the positive side, the drop in commodity prices has resulted in a reduction in operational costs, as the costs for fuel supplies and construction materials have decreased.

Jan 1, 2009

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

By Levent Ozdemir, Roy H. Spitzer, Don W. Deere, John B. Blyler

This paper documents the construction of the Stanley Canyon Tunnel, the geologic conditions encountered, boreability of the rock, and the impacts of the conditions encountered on the construction. The 5.05 kilometer long (3.1 miles), 3.47 meter (11.4 feet) diameter, tunnel was driven through granites with a refurbished tunnel boring machine (TBM). Difficult ground conditions encountered included shear zones, high groundwater flows, and hard, tough, and strong rock. Detailed geotechnical studies during construction revealed that microscopic changes in the rock grain boundaries due to contact metamorphism, resulted in the hard boreability. Originally scheduled for five months, the tunnel construction required nearly three years, including periods of project shutdown.

Jan 1, 1995

By G. Fehr, B. B. Panda, R. Bansberg, K. Arnold, T. Freiman

To evaluate the potential for process solutions to contaminate groundwater outside of the area of the Oxide Pit, it is necessary to predict the ultimate maximum pit lake elevation once pit-related mining activities have ceased. A water balance model was developed based on the existing pit geometry, the groundwater flow equation, and assumed hydrologic input parameters. The model assumed that at any point in time, total inflow into the system (i.e., direct precipitation, surface water and groundwater) minus outflow from the system (evaporation from the lake surface) was equal to the change in the pit water volume. The pit lake depth over time was predicted by assuming a succession of steady- state water balance conditions over short time increments. An analytical method using a spreadsheet and computer model was employed in this study to model the filling of the lake in the Oxide Pit. A sensitivity analysis was performed to evaluate uncertainty associated with the input parameters in the model. The sensitivity analysis indicated that the model was most sensitive to values of precipitation and evaporation and to the static water table.

Jan 1, 2003

By J. E. Osmanski

This semantically ambiguous title purports to describe an examination of the question of automation and its effect on the industrial worker. More explicit titles might be "Painless Automation" or "Mechanization without a Sting" or, if I may steal a few phrases from the title of a recent interview Pith John L. Lewis, "More Machines, Fewer Men -- Is the Union Happy About It?" Automation has become the biggest ?scare word? for many industrial workers and their unions since "wage stabilization.? "To many a union orator," reports TIME of January 4, "automation is the sinister business of eliminating jobs." TIME might better have phrased this description by saying that many unions regard automation as the attempt to eliminate not jobs, but workers, The recent steel dispute was hung up for so long primarily because of the problems evolved of increased job efficiency through automation and job changes. Everywhere today there is heard the cry of our need for maintaining full employment within the context of an expanding economy echoing against the sheer reality of automation's displacement of thousands of workers through a rapid acceleration of productivity.

Jan 1, 1960

By S. R. S. Sastri, K. K. Bhattacharya, K. S. Narasimhan

Experimental results obtained on the recovery of below 0.5 x 10-3m coal fines by flotation employing geometrically similar columns of 0.056m, 0.080m, 0.100m and 0.220m diameter have been presented. The hydrodynamics of such a unit as well as its performance have been related to operating parameters to establish optimum conditions. The results have further been analysed critically in the light of the known relationship on the behaviour of similar systems to assign reasons for the critical factors established in a bid to reduce the empiricism required to be followed in the scale up of such a unit.

Jan 1, 1988

By Horace M. Varner

Under sponsorship of the USBM and later of the DOE, a new type of rotary rock drill has been developed by The Bendix Corporation. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. This drill allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. The paper discusses various applications and experience for the flexible drill system in coal mining, metal/nonmetal mining, and for general civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1982

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By Douglas J. Pendrell, Marvin D. Simmons, E. Raymond Boc

The U. S. Army Corps of Engineers is in the early stages of design for an estimated 14 m (46 ft) diameter tunnel in northeast New Jersey. This tunnel will carry flood waters from the upper end of the Pompton River in Wayne County, to an outlet in Newark Bay, a distance of 33 km (20.5 miles). The tunnel will be constructed by a tunnel boring machine (TBM), the size of which is unprecedented at the present time. The alignment is through Triassic and Jurassic sandstones, siltstones, and shales that include three beds of basalt that range in thickness from 76 to 310 m (250 to 1020 ft).

Jan 1, 1991