Search Documents

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By R. V. Ramani, R. Bhaskar

While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mine environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use. As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined. The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.

Jan 1, 1987

By George F. Weaton

During the past eight years there has been a dramatic change in the iron ore industry of Minnesota, in that its status has changed from that of a seller's market to a higly competitive buyer's market. Minnesota's natural ores must now be beneficiated and up-graded considerably to be marketed in order to compete with the higher grade foreign ores as well as with the locally produced and highly desirable taconite pellets. With the passage of the "Taconite Amendment' in the November, 1964 election, the taconite industry commenced to expand in Minnesota, which, although initiated in that state, was benefiting many other states and some foreign countries to a much greater extent than Minnesota. These other areas were actually appropriating markets that had been established and retained by Minnesota for many years. Since the approval by the state voters of this amendment, there has been a great increase in the development of taconite properties on the Mesabi Range.

Jan 1, 1966

By A. K. Sinha

Research shows that continuous mining sections can normally produce around 950 tons per shift in a seam 5 or 6 ft. thick. The shuttle cars as well as the continuous haulage systems are able to match with the continuous miners in capacity. However, in practice both of the two systems seem to be averaging at around 450 to 500 tons per shift in production. Continuous haulage systems are preferred in thin seams particularly where the floor is soft.

Jan 1, 1981

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By John W. Crawford

The majority of the regulations in Part 75 for underground coal mines have been in effect since March of 1970, almost nine years now. Although there have been some additions each year in specific areas where the need became apparent or the statute required some action, the bulk was promulgated on March 28, 1970 for the purpose of clarifying the statutory provisions of the Federal Coal Mine Health and Safety Act of 1969. Many of those regulations were derived from the Federal Mine Safety Code, or from experience gained by the Bureau of Mines in the enforcement of Public Law 552. Upon passage of the Federal Mine Safety and Health Act of 1977, these same regulations remained in effect and the statutory requirements of the Act placed a responsibility upon the Secretary of Labor to promulgate additional regulations in specific areas not previously covered. The Federal inspectorate has received formal training at the National Mine Health and Safety Academy in the proper application of the regulations, as well as routine retraining and special training courses subsequent to the promulgation of new regulations. With some exceptions, the vast majority of these regulations are nothing more than good mining practice. Basically, the regulatory problems are two-fold. There are a few specific regulations that, under certain circumstances, compliance is nearly, if not actually, impossible. There is non-uniform application of enforcement of regulations by the inspectorate based on opinions developed from personal experience of inspectors or lack of experience. The record is replete with examples of overzealous inspectors applying regulations that either do not exist or have been stretched far beyond the intent of the regulations.

Jan 1, 1979

By C. G. Roache

Mining legislation in Jamaica dates back to only 1947 when, on August 30 of that year the Minerals (Vesting) Act was promulgated. None of the exploratory and trial-mining projects over the preceding 450 years were regulated or controlled by law. It was the seriousness of the intent of the North American Aluminum Companies to establish a bauxite mining industry in Jamaica which led to the development of the first piece of mineral legislation. It is of note that the incoming mineral industrialist was more anxious than the Government to see that a legislative framework was in place. It was relevant then as it is today for good mining legislation to be in place for the Government to regulate and control the exploration and exploitation of mineral resources. It was also necessary for the industry to know their rights and obligations so that they could plan, explore and exploit with some assurance that their capital was secure. One of the main reasons that the mining of bauxite did not begin in Jamaica until 1952 was that no legislational framework existed prior to 1947. The Jamaican dollar is tied to the US Dollar at a rate of J$35.00 to US$1.

Jan 1, 1998

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By Marion A. Goudie

The Devonian salt basin, which contains the Saskatchewan Potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota. The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 265 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis and Prairie Evaporite Formations. The Ashern formation, sometimes called the Third Red Bed, consists of dolomitic shales or shaly dolomites. The Winnipegosis is a reef type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The Prairie Evaporite formation consists of anhydrite overlain by halite and finally, in Saskatchewan, by the potash beds. In almost all wells which have been cored for potash the lowest potash bed is underlain by one or two bands of anhydrtte, which are used as marker horizons. Cores from a few wells which cored to the bottom of the salt series have shown flecks of potash throughout the halite.

Jan 1, 1959

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental and technical aspects of openpit mining operations. Factors influencing ore loss and dilution fall into two categories: (1) controllable factors, like mine equipment selectivity and blast design, and (2) uncontrollable factors, such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls preblast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, through a number of case studies, the study investigates the relationship between spatial entropy, cutoff grades, blast movement, dig-limits optimization model running time, and profit. The results show that changes in cutoff grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy

Jun 1, 2024

Mining was the first economic activity carried out in Cuba, by the colonial conquerous, i.e. gold extraction from rivers and use of asphalt to calk their ships; however, due to different historic reasons only a limited development took place in this field during the colonial domination. During the republican period beginning early in this century, other interests lead to a larger scale exploitation of some known deposits. From the beginning of the century up to the triumph of the Revolution in 1959, not less than the following figures were extracted of some Cuban minerals: Refractory Chromium 3,300,000t Manganese 7,650,000 t Copper 9,000,000 t Iron 22,000,000 t Nickel 150,000 t (Ni oxide and sulphide These productions were practically directed to cover the demands of the U.S., industry and some-times these Cuban ores were almost the sole suppliers of the market.

Jan 1, 1978

By Michael Fellows

Epidote is a common hydrothermal alteration product in many copper deposits of the southwestern United States. In many of these deposits epidote, along with calcite and chlorite, generally characterize a distal or halo propylitic alteration assemblage, but the mineral can occur within the central potassic alteration zone as well. Epidote is also a common alteration mineral in deposits formed in calcareous host rocks -- the skarn or pyrometasomatic ore bodies. Within the past 15 years, studies of the major and trace element composition of other alteration phases, principally biotite, associated with base metal ore deposits have demonstrated that some hydrothermal alteration minerals are compositional distinct from their igneous or metamorphic counterparts: However, the use of major and minor element content to identify and zero in on mineral¬ized areas does not appear to be very promising. Little work has been published upon the geochemistry of epidote from this standpoint and the results of my work suggest that a similar conclusion can be applied to epidote. My work (Fellows, 1976) suggests that epidote minerals in hydrothermal alteration suites from porphyry copper deposits in the southwestern United States are generally iron-rich rather than aluminum-rich. As a group, these alteration minerals differ compositionally from epidotes of regional metamorphic terrains. I ascribe these differences to the variations in the oxidation character of the respective environments. However, it appears as though the use of major element compositional variations of epidotes as an exploration tool is severely limited. Epidote is a complex calcium-aluminum silicate. Replacement of aluminum by ferric iron establishes a solid solution series between

Jan 1, 1977

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By S. B. Patton, T. Novak

To fully utilize a ventilation simulator as a planning and production tool, the network database must keep pace with mining progress. By using AutoCAD's™ attribute-definition function, the branch data and node coordinates can be stored as part of the branch-diagram file and updated with the drawing. Attributes are drawing entities that contain text which can he extracted in a standard spreadsheet format or as an ASCII text file. The data can be subsequently loaded into a ventilation simulator. This paper presents the methodology for using AutoCAD's™ attribute feature in a ventilation simulation format.

Jan 1, 1995

By P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber, caulks, and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness, and outstanding rheology in water systems. The quality of calcitic GCC ores, which include chalk, limestone, and marble, is dependent on calcite purity and the nature and quantity of ancillary minerals. Wet and dry grinding is used in the manufacture of GCC. Ore processed by optical sorting, flotation, and/or particle size classification has higher brightness and lower abrasion. GCC markets are a function of the product's properties, purity, and cost.

Jan 1, 1995

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By James K. Gowans

Polaris Mine, a Cominco Ltd. property located on Little Cornwallis Island, Northwest Territories, Canada, (Lat. 75°30'), is the world's most northerly base metal mine. Polaris Mine, which commenced operations in late 1981, is characterized by its unique process barge. The lead/zinc concentrator, powerhouse, shops, offices, dry and warehouse have all been incorporated on a 400 ft. long by 100 ft wide by 65 ft high barge. This process barge was constructed in Southern Canada, at Trois Rivieres, Quebec, then towed 3500 miles into its final resting place on the high arctic. This paper describes the unique design of the barge concentrator and deals with the start-up and continuing operation of the Polaris Concentrator.

Jan 1, 1984

By R. R. Graham

Echo Bay Minerals operates a 650 tpd gravity float gold circuit at their Manhattan facility. The objective of this paper was to document the gold recovery by size distribution. This was accomplished by studying the material balance of each size fraction as it progressed through each gravity Circuit separator. It proved to be an impossible task. Figure I depicts the gravity circuit. The gravity cyclone underflow goes to two duplex Pan American type jigs. The jig overflow reports to the OK Flash Float Cell. The cyclone hutch product is reground and goes to a full size wilfly table. The rougher table concentrate reports to a pilot size Wi1fly cleaner table. The cleaner and rougher table tails circulate back to the jig feed. The gravity circuit was composite sampled for two to four hours per day for four days. Each sample was taken every 20 minutes. Each composite sample was filtered, dried, repu1ped, and screened through a wet/dry screening procedure. Each size fraction was checked for gold value by fire assay fussion technique. A material balance was run on each size fraction. The tables listing the results are enclosed.

Jan 1, 1989