Search Documents

By Gale F. Hoffnagle

INTRODUCTION On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. These Amendments cover many aspects of air pollution control. The provisions which seek to control emissions of "air toxics" may, however, be the most far-reaching and will potentially have the greatest effect on American industry. The Administration has estimated that by the year 2005 industry will be spending $6.7 billion per year on air toxics control. Meanwhile, the Business Round Table has estimated that the price will be far higher, up to $62 billion per year, depending on how EPA and the States implement the program. BASIC REQUIREMENTS Any "major" source of emissions of 189 air toxics will be required to install "MACT." The translation of this statement requires some definitions: •MAJOR SOURCE - A facility (a contiguous property under single ownership and control) which has actual emissions of 10 tons or more per year of any single one of the air toxics or 25 tons per year of any combination of air toxics. •AIR TOXICS - Congress has provided a list of the 189 chemicals on this list. Those that may be important to the mining industry are shown on Table 1. This list can be changed by petition or by EPA. •MACT - Maximum Achievable Control Technology is to be defined by EPA for each industrial source category. EPA says there are about 400 categories. The Act defines MACT as: "the average emission limit achieved by the best performing 12% of the existing sources ... for categories with 30 sources or more" or, "the average emission limitation achieved by the best performing 5 sources in the category." TABLE 1 SELECTED AIR TOXICS FROM CLEAN AIR ACT LIST IMPORTANT TO MINING INDUSTRY Antimony Compounds Arsenic compounds (inorganic including arsenic)' Beryllium Compounds' Cadmium Compounds Chromium Compounds Colbalt Compounds Cyanide Compounds (dissociation compounds) Lead Compounds' Manganese Compounds Mercury Compounds' Fine Mineral Fibers Nickel Compounds Radionuclides (including radon)1 Selenium Compounds 1Previously listed under NESHAP 2The Administration may not list elemental lead as a hazardous air pollutant.

Jan 1, 1991

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By D. V. Bush

The economic application of real time computer control can be broken down into 2 broad areas of concern. The first would be in gaining the most efficient utilization of energy. The second would be in improved product quality. This paper will be primarly concerned with the first area of efficient energy utilization as that area has the greatest effect on costs and thus net profits. Most process control strategy attempt to achieve the greatest comminution with the least amount of energy thus maximizing efficiency. A more direct approach to energy control involves a total mine and mill energy management system. In most cases these systems have an ability to achieve a very short payback period with the greatest return on investment.

Jan 1, 1986

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977

By José Luis Lee Moreno

This paper presents a preliminary phase of a study being conducted by the Department of Geochemistry of the Consejo de Recursos Naturales No Renovables in the vicinity of the Pachuca-Real del Monte Mining District. This district is located in central Mexico, about 100 km northeast of Mexico City. It has been in operation for the past 450 years and has produced about 38 million kg of silver and about 190 thousand kg of gold. At the present it is being worked by the state owned mining company of Real del Monte and Pachuca. The rocks of the area consist mainly of Tertiary volcanics, ranging in age from early Oligocene to late Pliocene. Ore bodies are recognized as epithermal, vein type fracture fillings. The main ore minerals are argentite and acanthite normally accompanied by base metal sulphides, Gold is present in small amounts as native gold and in other minerals. Orientation geochemical studies performed on soil and rocks over known veins in the district, showed zinc to be the best indicator. Lead and silver anomalies are restricted to the immediate vicinity of the veins, mercury shows the mineralized structures only when the "C" horizon is sampled, while antimony gave erratic values. The El Chico area is about 10 km north of the Pachuca-Real del Monte district and covers approximately 400 sq km. Geological evidence indicated the possibility of an extension of the Pachuca ore bodies in this area. Results obtained from soil and rock samples from El Chico, showed several anomalous area. Detailed investigations proved these anomalies to be related to faults and fractures which in several cases have been found to be mineralized. Drilling is planned with preliminary results expected by late 1974.

Jan 1, 1974

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By J. H. Calder, J. C. Hower

Three lithotypes of Phalen coal from Cape Breton County, Nova Scotia, Canada, were subjected to a modified Hardgrove grindability index (HGI) test. The testing scheme differed from conventional (ASTM D-409) Hardgrove testing by, in one case, repeating the test three times prior to removing the -200-mesh fine coal from the Hardgrove mill, and, in a second test, removing fines after each of three successive Hardgrove tests. Only the first stage of the latter testing scheme actually conforms to the standard HGI test. All processed samples were analyzed petrographically by a combined maceral/microlithotype analysis. The increase in the percentage of coal ground to -200 mesh increases through the 60- to 180-mesh fractions for each of the lithotypes for the following two apparent reasons. First, with progressive grinding, more of the oversize material is close to 200 mesh (75 µm), creating a "pool" of particles ready to be ground to -200 mesh, and, second, the removal of fines from the system at each step eases the grinding at the successive step. The fines retained system shows the influence of buffering of further grinding by the particles retained in the grinding mill. The Phalen lithotypes and the series of Central Appalachian coals, evaluated previously by Hower and Wild (1994), differ in that an increase in vitrite and a decrease in trimacerite is observed in successive -200-mesh fractions in two of the Phalen lithotypes. This is the opposite of the trend observed in the slightly lower-rank Central Appalachian coals.

Jan 1, 1998

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By Betty L. Gibbs

Computer software for mining applications has been in development since before 1970. These packages cover tasks from exploration data management through final reclamation planning. These programs were originally written in Fortran and have evolved into colorful, user-friendly packages. Programs that produced printed symbol maps now show color, three-dimensional image of an ore deposit on a computer screen. Pictures can be rotated and looked at it from all directions and layers can be peeled off to show other parts of a model. Computer users have also evolved. In the early Fortran days, users had to learn computer operating systems, have someone punch data cards, set up run files and wait a day or so to find out if there was one little mistake somewhere that caused the program not to run. With today&apos;s technology, users sit at their desks in the office, key in some data, read other data from digital files and build a model within days, rather than weeks or months.

Jan 1, 1999

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By K. Ohga

Japan has produced 14-16 million tons of coal per year in the past several years. About half of the production comes from eight coal mines in the Ishikari coal field, Hokkaido. Most of the gassy coal mines are in this field and the average mining depth of these coal mines has already attained about 700 m from the surface. Therefore, most of the coal mines have suffered from occurrences of coal and gas outbursts. To prevent outbursts and to reduce ventilation air, gas drainage has been carried out at all of these coal mines and these have had successful results. However, the methods of gas drainage differ from mine to mine. In this report, an outline of the main methods of gas drainage are described.

Jan 1, 1987

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

By William Laird

In the process of mining coal today, our greatest asset, the coal miner, is faced with the indirect and direct consequence of underground mining operations. The indirect considerations may be the rank of the coal seam, the amount of overburden, geological factors, seam permeability and cracks. The introduction of newer, bigger and faster coal-producing face equipment having the capability to cut or rip through the bedding planes, cleats and micropores of the coal seam brings about rapid liberation of gas accompanied by greater concentrations of coal dust, has exerted a direct consideration and greater demand upon mine ventilation systems and dust control. The purpose of mine ventilation is to provide sufficient pure air to the miners working underground and to dilute, render harmless, and carry away all the dangerous and noxious gases. The mining operations which create coal dust are cod cutting, drilling, blasting, loading, hauling, dumping and movement of face equipment. The created fine dust causes the propagation of explosions. When quantities of coal dust with no methane present are raked in a sufficiently dense cloud in the presence of a source of ignition, an explosion is possible.

Jan 1, 1980

By Duk-Won Park

The stability problems of back- filled spoil banks became more important since the Federal Surface Mining Control and Reclamation Act of 1977 was enacted. The material properties of spoil banks were categorized as the first part of the study and spoil slope stability was evaluated using computer programs as a second part. Emphasis was placed on the effects of natural barriers, which is required in the federal law.

Jan 1, 1982

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005