Search Documents

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By S. C. Suboleski

Underground long-range planning and mine design is an iterative process beginning with a specified production level, quality criteria, and geology of the deposit. Given these factors, face equipment is selected, the number of units needed and production per unit are calculated, and the mine infrastructure needs are developed. The scheduling of units then follows, with the design of the various support systems coming next. The support systems needed to maintain production can be grouped as follows: (1) outby haulage of mined material, (2) supply and manpower haulage, (3) ventilation and associated environmental considerations, (4) drainage, fresh water, and related considerations, (5) rock mechanics, and (6) power, supply. Thus, long-range planning may be viewed as a three-tiered structure, with the data on required production, product quality, and geology at the upper level; the development of face production capacity and the scheduling of units sufficient to meet the needs of the first two at the second level; and the development of support operations for the production units at the third level. Changes at any level may affect not only the items on that tier but may also cause a change to the items on the tier above and below. For example, if the rock mechanics data indicate that desired opening sizes will not be stable, then this situation will affect not only the ventilation design but also the production rate and possibly the selection of equipment itself. These, in turn, may affect the scheduling of units and the number of units, ultimately influencing the entire third tier of systems.

Jan 1, 1979

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By AKIHIRO YOSHIMURA, HIDEKAZU KATO, KOTA TAKATORI, YASUNARI MATSUNO

Chalcopyrite (CuFeS2) is the most refractory copper mineral when treated in conventional sulfate media leaching systems. This study is the first to examine the use of a dimethyl sulfoxide (CH3SOCH3), or DMSO, solution containing copper chloride (CuCl2) in the leaching of chalcopyrite. The DMSO solution containing CuCl2 could selectively dissolve the valuable metals of copper (Cu) and gold (Au) from chalcopyrite while leaving minerals with little economic value, such as pyrite (FeS2), and the penalty element arsenic (As) in the residues. Leaching chalcopyrite using a DMSO solution that contains CuCl2 offers a number of advantages, including eco-friendliness and easy operation.

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By J. P. De Carvalho, R. Dimitrakopoulos

An actor-critic reinforcement learning approach is presented to improve the production of an industrial mining complex by defining shovel allocation and adapting the short-term plan given grade-control decisions. Blasthole data updates the simulated orebody models, which are input into a stochastic grade-control method based on a spatially constrained clustering approach that minimizes the profit-loss function. These aspects are embedded in a discrete-event simulator that defines the material flow from faces to processors. A case study at a copper mining complex shows the methods’ ability to adapt to new information, improving the quality of the material feed and increasing cash flow by 23% compared to a baseline case.

Jun 25, 2023

By Lynton B. Manssen

Introduction Net Present Value (NPV) techniques are becoming widely used in industry as a standard analytical tool in making capital budgeting decisions. However, NPV techniques are often misused in "common practice." A comparison was made between the use of NPV techniques in common practice and an Adjusted Net Present Value (ANPV) approach to capital budgeting in the financial analysis of a mining project. The comparison was made by applying both methods to a hypothetical copper project. The intent of the analysis is to provide an example for practitioners to follow when financially analyzing mining (or other) projects. To maintain the thrust of the analysis, the project has been evaluated as a stand alone, total project. No consideration has been made of the division of cash flows accruing to various owners over the life of the project. This omission will not affect the comparative nature of the analysis. This discussion assumes that the reader is familiar with present value as a concept and as a tool in capital budgeting. Finance theory has embraced NPV analysis as the correct way to evaluate capital budgeting alternatives. Many articles have been written expounding the virtues of NPV over other capital budgeting methods, such as Internal Rate of Return (IRR), Payback, Accounting Rate of Return, and others. It is not the purpose of this article to review all of the literature in this area; suffice it to say that in academic circles NPV concepts are accepted as the norm. A survey by Schall, Sundem, and Geijsbeck (1978) indicates that major US companies are finally following in academia's footsteps. Fifty-six percent of the companies responding to the survey use NPV techniques in their capital budgeting process. Further, some 86% of the companies surveyed use discounted cash flow methods (NPV or IRR) for capital budgeting decisions. This compares with a survey by Klammer (1972) that showed 57% of companies using both techniques, a considerable increase in seven years. With the increasing use of NPV techniques in industry, there are certain uses in common practice that can give misleading results. Five common errors in NPV analysis of large projects are: • No distinction is made between real and nominal cashflows. • The discount rate(s) used in the NPV analysis is not formally adjusted for risk. • There is no distinction of possible differences in the riskiness of different project cash flows; i.e., revenue vs. depreciation. • There is no recognition of the cash benefits to the project from interest tax shields (interest payments on the project's debt that are tax deductible). • There is no clear recognition of subsidies to the project from concessionary debt financing. No Distinction Between Real and Nominal Cash Flows Often, expected cash flows for a project are stated as a mixture of real (in constant dollars) and nominal (in current dollars) cash flows. For example, expected revenue cash flows may be stated in real terms and depreciation may be stated in nominal terms. If cash flows are added together to give an after tax cash flow, and this single cash stream is discounted, care must be taken to ensure that cash flows are consistently stated. All cash flows should either be stated in nominal terms or in real terms. In addition, the discount rate used must be stated in the same terms as the cash flows being discounted. Real cash flows must be discounted using real discount rates and nominal cash flows using nominal discount rates. Discount Rate Not Adjusted Numerous methods for obtaining discount rates are used in common practice. Schall and others

Jan 6, 1983

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By Robert J. Hite, James P. Searls, Sherilyn C. Williams-Stroud

Potash is a generic term that includes potassium chloride, potassium magnesium sulfate, potassium sulfate, potassium nitrate, and sodium-potassium nitrate mixtures. In the ceramics industry, potash is also used to refer to potassium oxide. Potash, primarily in the form of potassium carbonate, was the first industrial mineral produced in the United States, and the first US patent issued was for an apparatus and process developed in 1790 for its production (Paynter, 1990). Prior to the 1860s, potash was primarily sold as an impure form of potassium carbonate produced by burning hard- wood trees and leaching the potassium salts from the ashes. The major early uses of potash include soap and glass making, dyeing fabrics, baking, and saltpeter for gunpowder. In 1859, the development of a purification process to remove the sodium and magnesium chlorides was developed for the carnallite found at Stassfurt, Germany, and mined potash became available. With the appearance of mined potash and the earlier (1840) discovery in Germany by Justus von Liebig that potash was a nutrient for crops, potash started to be used for high valued crops such as cotton and vegetables. The German potash companies quickly developed a manufacturing process for producing potassium sulfate for tobacco fertilization. German potash supplied nearly all American needs until the embargo of the First World War when imports from Germany were interrupted (Bateman, 1918). With the discovery of potash deposits in New Mexico in 1931, the United States became self-sufficient in potash. In 1962, the United States began importing potash from Canada, and two years later domestic apparent consumption began to exceed domestic production. Along with nitrogen and phosphorus, potassium is one of the three essential plant nutrients, the "K" of NPK terminology. As a result, 95% of potash production is used as plant fertilizer. In all plants, inadequate potassium diminishes growth, causes increased disease, stalk and stem breakage, and susceptibility to other stress conditions. Plants take up large quantities of potassium from the soil, and potash fertilization replaces this loss so that each new crop can be grown with the same vigor and productivity as the previous year's crop. The potassium depletion of the soil from growing repeated cotton and tobacco crops is well known in the history of southern agriculture in America. George Washington was known to have studied alternative crops that could be grown on soil that had been depleted by repeated tobacco crops. Most of the remaining 5% of potash consumption is by the chemical industry, as potassium hydroxide to produce soaps and detergents, glass and ceramic products, dyes, explosives, alkaline batteries, and medicines. Potash as chemical is used in oil field drilling mud, the aluminum recycling industry, and the electroplating industry. Additional minor uses for potassium chloride include water softener regeneration, sidewalk deicing, and salt substitution for human consumption. Potash is used in the food industry as potassium phosphate, and in production of glass products as potassium carbonate or nitrate. GEOLOGY Potassium is the seventh most abundant element in the earth's crust and the sixth most abundant element in seawater. It is found in silicate minerals of igneous, metamorphic, and sedimentary rocks and is also a major constituent of many surface and subsurface brines. The majority of world potash resources are found in subsurface bedded salt deposits which yield high grade, large tonnage ore bodies and are amenable to low cost mining and beneficiation. Because of the relatively high solubility of potassium minerals, potash from salt deposits is ideal for use as fertilizers. Some potash production is from evaporation of naturally occurring brines, but the vast majority of current domestic and international production is from bedded salt deposits. Sylvite, carnallite, kainite, and langbeinite are some of the more important potassium minerals (Table 1). Sylvinite, a mixture of KC1 and NaCl is the highest grade potash ore. Carnallite can be considered a potash ore when removal of magnesium chloride is included in the beneficiation, but it can also be considered a contaminant when mining for sylvite. Potassium sulfate and potassium nitrate are typically manufactured products. Potassium sulfate is produced from mined minerals through conversion processes in Italy, Germany, and Carlsbad, NM, and from brines in southern California and at the Great Salt Lake in Utah. Natural deposits of potassium nitrate occur only in small amounts in Chile. The majority of potash-bearing bedded salt deposits are believed to have originated from the evaporation of seawater or mixtures of seawater and other brines in restricted marine basins (Schmalz, 1969). The reflux depositional model for evaporite deposition was first described in the literature in 1888 by Ochsenius. A shallow bar, or sill, across the mouth of a basin lets in a restricted flow of seawater which evaporates into a salt-precipitating brine (Fig. 1). The density of the brine at the distal end increases with increased salinity, sinks to the bottom, and sets up a reflux current of higher density brine back toward the ocean. The sill, which restricts the inflow of seawater, allows inhibited flow of evaporation-concentrated brines back to the ocean. The least soluble salts are precipitated nearer the sill, and the most soluble components come out of solution in the deeper parts of the basin. The result is a lateral facies change in a tabular-shaped deposit that is due to the salinity gradients in the brine (Fig. 2A). The asymmetrical facies distribution of the Paradox Formation (Middle Pennsylvanian) Utah (Hite, 1970), the Prairie Formation (Middle Devonian) in Saskatchewan (Holter, 1972), and the Salado Formation (Upper Permian) in New Mexico (Lowenstein, 1988), might prompt explanation by such a model. Other deposits, such as the Salina Formation (Upper Silurian) in Michigan (Matthews and Egleson, 1974), show a facies distribution that could be described as a bull's eye pattern. Although some small subbasins of high grade sylvite are found near the margins, the potash is generally located in a central part of the basin surrounded by successively less soluble facies (Fig. 2B). The sparse

Jan 1, 1994