Search Documents

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By K. Kuhnhenn, G. Prommersberger

General aspects In Germany, swelling rock is mostly found in the keuper formation. Keuper is a sedimentary rock formation of varying composition. It mostly consists of fine or medium layers of clay/silt/marl/dolomite stone with intercalations of gypsum or anhydrite in strips or nodes. After disintegration of the top layers and tectonical incidents, the gypsum level, i.e. the upper [ ]

Jan 1, 1989

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By David F. Gibson

This paper presents an outline of several models that have been developed to aid surface mine planners evaluate alternative mining methods and dragline sizes. The models presented belong to a larger group of models that are incorporated in the SEAMPLAN computerized mine and reclamation planning system. SEAMPLAN was developed in the College of Engineering at Montana State University. Initial funding for the development was derived from the USDA Forest Ser- vice and EPA. Enhancements to SEAMPLAN are currently being funded by DOE (Contract DE-AC22-80ET-14173). SEAMPLAN is a comprehensive surface mine and reclamation planning tool that contains a number of major modules: Data Entry and Review, Production Analysis, Reclamation Analysis, and Impact Analysis. The Production Analysis Module contains programs that enable the user to evaluate alternative methods of removing overburden in a surface coal mine and then to assess auxiliary activities required to support the overburden removal operation. A set of these programs addresses the use of draglines for removing overburden. Six basic dragline mining techniques have been modeled. For one-pass dragline operations four methods can be analyzed: (i) simple side cast, (ii) side bench, (iii) extended bench, and (iv) extended bench with side bench. Two methods of two-pass operations are modeled: (i) single dragline, and (ii) tandem draglines.

Jan 1, 1982

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By R. S. Austin

One third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. . Its whiteness, brightness, fine particle size, platelet shape, surface chemistry, and chemical composition make kaolin an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By John D. Morgan

The United States is the world's most productive nation and its citizens enjoy one of the highest material standards of living of any people in the world. Materials and energy are the lifeblood of any industrialized economy. Annually the United States uses over 4 billion tons of mineral materials and fuels, or 40,000 pounds per person as detailed in Figure 1. Domestic processed materials of mineral origin and energy are valued at more than $150 billion annually, and they are derived largely from domestic sources, supplemented by imports, as detailed in Figure 2. In recent years the superior productivity of the United States has also enabled it to give food and manufactured articles to many other less fortunate nations and peoples of the earth. What then is our concern with materials at this time? Seeing the burgeoning increases in our mineral demand: from 2 billion tons in 1950, to over 4 billion tons today, and projected to 11 billion tons by 2000 - we are getting questions concerning our ability to continue to increase production sufficiently for the future.

Jan 1, 1974

By C. Wayne Burnham

Much has been written about hydrothermal alteration and the compositional changes induced by it in the wallrocks of mineral deposits, especially in alummino-silicate wallrocks. So much has been written and the descriptions so varied, in fact, that the casual reader frequently is bewildered by the extreme complexities and lack of uniformity, real or apparent. Certainly the mineralogy and chemistry of altered rocks are not as simple as most of us would like, but neither are they as complex in their principal aspects as pa of what has been written would lead us to believe. The trend until recently seems to have been toward greater complexity and hence greater confusion, but the straightforward presentation of Creasey (1959), it is hoped, marks a reversal in this trend.

Jan 1, 1962

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By Don Runge, John T. Zeni

Cuprex Limited is currently developing a small gold mining operation in Central Australia in the Tennant Creek field. In February 1984, the company undertook a feasibility study on the project and operations commenced in August 1984. Ore reserves are located between 230 and 280 metres (755 ft and 919 ft) below surface and ore extraction required the establishment of a shaft network for access, ore hoisting and ventilation. Zeni Drilling Company from West Virginia, U.S.A. was contracted to blind drill two shafts for the project. Blind drilling was selected for various reasons, including timing which related to cost efficiency. The blind drill shaft technique has proved successful in this application and with enthusiastic and innovative support from the mining industry, will prove an efficient and cost effective means of accessing and operating underground mining projects of all sizes in the future.

Jan 1, 1987

By John K. Liu

The trend to larger grinding mills, requiring total drive power in the range of 10,000 KW(13,400 HP) or so provides the incentive for developing new power transmitting techniques, since conventional girth gears are limited to about 3700 to 4500 KW per mesh (5000-6000 HP). For the immediate future, the synchronous motor, with its beneficial power factor, and the squirrel cage induction motor, with its high reliability record and low maintenance, still promise to be the best choice for prime mover(s). Due to the abovementioned single mesh power limitation of the gear train, however, two or more motors must be combined to attain the required drive power. This paper describes a scheme for coupling these motors to the mill using a straightforward, essentially mechanical means that is based on proven components and controls.

Jan 1, 1977

By Roger B. Jr. Herbert

Surface water samples were collected from water accumulations at the surface of a neutral pH mine tailings deposit in Kristineberg (Sweden) where algal growth and iron hydroxide precipitates were observed. Ferric iron in the aqueous samples was determined by (adsorptive) differential pulse - cathodic stripping voltammetry. The analyses indicated that labile Fe3+ concentrations were in the range <20 to 337 nM, while total Fe3+ levels were much higher at 0.9 to 8.3 uM. The labile Fe3+ levels are more than two orders of magnitude greater than would be expected based on equilibrium with ferrihydrite. These results suggest that iron complexation with strong ligands in the surface water competes with iron hydrolysis, and that these ligands may be of algal and/or bacterial origin.

Jan 1, 2000

By Y. C. Kim, F. Szidarovsky

The technique of linear kriging as a grade estimation method of mining blocks is reason¬ably established in the mining industry. During the kriging process, negative kriging weights ([]i) are sometimes encountered. Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense. To guarantee nonnegative weights, an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of nonlinear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer, time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over-or underestimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1987

By Z. Kokesz

The following paper presents the results of geostatistical studies of the selected hard-coal deposits in Poland. Geostatistical methods were applied mainly to the characterization of variability structure of the coal seams thicknesses as well as sulphur and ash contents in the coals. Results imply that the accuracy of coal reserves estimations can be improved if kriging method is applied. Kriging allows predicting more precisely the values of such parameters as thickness and sulphuring content.

Jan 1, 1993

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987

By R. Jerez

This paper describes practical applications of lineal" programming techniques to help in the planning of production, transportation and shipments at different coal mines. The models are being used by Cyprus Coal Company in eastern and western operations to plan coal production, economic dispatching and blending over variable time horizons. In addition, where a preparation plant exists, the models establish the amount of washing required to meet specific coal sales qualities. The emphasis on this paper is on model development and implementation together with a system to track coal flow and qualities, either raw from the mines to the loading facilities 01" processed through a preparation plant.

Jan 1, 1991

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By F. Ysla, M. Mendoza

This proposal, based on the CIEMAN Cajamarca - Hualgayoc initiative, focuses on “Transforming Abandoned Mine Lands’’ We aim to study and assess the feasibility of an innovative rehabilitation method. Contaminated soils will be moved from the upper to the lower site, encapsulated with geosynthetic barriers, and covered with topsoil. The decontaminated upper area will be used for planting trees and large-stemmed plants for hiking and tourism, while the lower encapsulated area will support livestock and short- stemmed crops. This study will evaluate the economic viability and multi-use potential of this technique, promoting sustainable land recovery in Cajamarca, Peru.

Feb 1, 2025

By Y. C. Kim

One aspect of long-range mine planning in an open-pit mine is first to define the ultimate pit limit, i.e., the projected size and shape of the pit at the end of its life. This chapter is concerned with various techniques that are currently in use today in determining the ultimate pit limits using the computer. Prior to the early 1960&apos;s, open-pit limits analyses were entirely performed manually. This manual technique has been well explained by Soderberg and Rausch in Surface Mining (1968). Soderberg and Rausch also explain clearly the need for establishing the ultimate pit limits in long-range mine planning, i.e., location of surface facilities, dumps, etc. Consequently, the need for ultimate pit limit design will not be reiterated here. Nor will the definitions of the most commonly accepted terminologies such as break-even stripping ratio, economic cutoff grade, ultimate and working slope angles, preproduction stripping, etc. be repeated here. Briefly, the objective of the ultimate pit limit design (which is also frequently referred to as pit design in short) is to determine the projected final pit limits of an ore body and its associated projected grade and tonnage, which will maximize some prespecified economic criteria while satisfying practical operational requirements.

Jan 1, 1979

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999