Search Documents

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By R. Stocker

Flotation recovery of molybdenite particles finer than 15 micrones sharpy decreases with decreasing size. A totally hydrophobic latex agglomerant (UBC-1), which was previously reported to be very efficient in agglomerating hydrophobic fine coal, has been found to agglomerate fine molybdenite particles. The agglomeration takes place only in the presence of MIBC which is commonly used as a frother in molybdenite flotation. Adsorption tests confirmed that MIBC is adsorbed onto molybdenite. The effect of the agglomeration on flotation has been studied by floating fine molybdenite from mixtures with quartz using the UBC-l agglomerant and the MIBC frother. A significant improvement in the flotation of fine molybdenite has been observed in the presence of the UBC-l agglomerant. The best results have been obtained around pH 5.5 which corresponds to the iso-electric-point of molybdenite.

Jan 1, 1997

By William C. Ellis

Underground water is part of a continuing hydrologic cycle, which involves all elements of water occurrence. All groundwater of economic importance is in process of movement through a porous rock stratum from a place of intake or recharge to a place of disposal. Groundwater moves and is contained in fractures in the rock and/or in intergranular spaces of porous formations. Where there have been no water developments by man, groundwater is in a state of approximate equilibrium and the forces of replenishment and discharge are in balance. Thus, groundwater, unlike other mineral resources, is constantly being replenished in most areas at a rate which is measurable and which is important in the planning of its utilization. As illustrated by Figure 1, replenishment of groundwater supplies results from the direct penetration of rainfall through the soil to the water table, by seepage from surface streams or ponds, and/or by subsurface movement from an adjacent groundwater body. Under natural discharge conditions, water is commonly consumed by transpiration of trees and other types of vegetation, by flows from springs, by evaporation from shallow depths below the surface, and seepage into streams that traverse the area.

Jan 1, 1964

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By Robert Stefanko

The most perplexing problem that has confronted mining engineers since the dawn of mining has been strata control. For the purposes of this paper, strata control will be defined as control of ground in the immediate area surrounding the, mine opening. To prevent movement of the surrounding strata into underground mine openings, miners have traditionally relied upon some type of artificial supports placed within the openings and located in a manner determined by trial and error from previous experience. Without the means to measure changes of stress in the supports and within the mine structure itself, an evaluation of the efficiency of the supports and mining system was impossible. Strata control thus remained an art with very little application of science. During recent years a revolution has occurred in mining. The modern mining engineer is contented no longer-with trial and error methods but is utilizing all the technological information at his command to obtain a solution to this age old problem. However, serious problems have arisen due to the lack of certain basic knowledge in three important areas: 1, The original stress distribution within the earth strata prior to mining. 2, Redistribution and concentration of the original stresses with mining activity. 3. The properties of rock that are significant in failure and its prevention.

Jan 1, 1960

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By David M. Kjos

Large diameter autogenous and semi-autogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semi-autogenous mills have reached an acceptable level of technology which provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant it is to be installed in. This is particularly true in autogenous and semi-autogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only ?paper.? Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs and operating practices, and provide some guidelines for good practice as we move through the 1980's. We will put together concepts that relate to the designs, materials and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series because they are dependent on each other to achieve the desired performance.

Jan 1, 1985

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of 'small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

Large variations of coal seam thickness and roof conditions are associated with the occurrence of mine floor undulation at Shoal Creek Mine, operated by Drummond Company, Inc.. Ground control problems, such as roof falls and face failures along with extremely high shield pressure and rapid face convergence, are often reported at the longwall face when these undulations exist. This greatly increases equipment downtime and causes production delays. As a result. a comprehensive study of mine geology including roof conditions and longwall performance were conducted in the mine. With the help of continuous full-face shield pressure monitoring using the Longwall Strata Control and Maintenance System (LoSCoMS), a large data base of shield pressure with various roof conditions has been established. This enables the mine operators to accurately evaluate the roof behavior and shield performance and to take the appropriate operational steps at the face to reduce the number of downtime and face failures. This paper summarizes all works and findings from the study including detailed roof geology and its effect on longwall performance.

Jan 1, 1998

By Kenneth S. Johnson

High-purity gypsum of Permian age crops out in three major gypsum districts of western Oklahoma. The northwest and southwest districts have important reserves in the Blaine Formation, whereas reserves of the west-central district are in the Cloud Chief Formation. Gypsum beds of the Blaine Formation typically are 10 to 30 feet thick, 95 to 99 percent pure, and interbedded with shales that are 2 to 30 feet thick. The base of the Cloud Chief Formation consists of a massive bed of gypsum that typically is 20 to 100 feet thick and is 92 to 97 percent pure. Anhydrite is present in the sulfate beds, beneath 20 to 100 feet of overburden, at a number of places in all three districts. Total gypsum reserves in the three districts are estimated at 48 billion short tons. These reserves are well suited for open-pit mining or quarrying, because gypsum typically forms hills in the semiarid climate of western Oklahoma, and the gypsum layers are nearly flat lying, without folds or faults. Seven companies currently mine a total of 1.0 to 1.4 million tons of Oklahoma gypsum each year for wallboard, for plaster, as a retarder in portland cement, and as a soil conditioner.

Jan 1, 1978

By W. J. Atkinson, E. M. Anderson

FOREWORD This paper is based on the authors' experience gained in the environmental assessment of major uranium projects in the former Department of Science and the Environment and Department of Home Affairs and Environment of the Australian Government. The authors gratefully acknowledge assistance received from colleagues within the Department of Home Affairs and Environment in the preparation of this paper. Special thanks go to Mr K.E. Thompson of the Department's Environment Division for his valuable comments and criticism. The views expressed in the paper are those of the authors alone and not the Australian Government or Dames & Moore. INTRODUCTION Uranium has been mined in Australia since 1954. A number of small scale mining and milling operations were active in the Northern Territory, in South Australia and in Queensland in the late fifties and early sixties. However, in the late sixties there was an increase in exploration activities in the expectation of an upsurge in world demand for uranium Substantial new resources were delineated in the Northern Territory, Queensland, South Australia and Western Australia. The most significant deposits were located in the Northern Territory, in what is called the Alligator Rivers Region located approximately 200 km east of Darwin. The Region is in the latitude of 13° South and thus lies within the Australian tropics (Figure 1). It consists of approximately 2.3 million hectares of natural wilderness containing much spectacular and attractive scenery. The area is noted for its abundant wildlife, particularly the waterbirds that gather on the flood-plains. Much of the vegetation is diverse and interesting. The Aboriginal population still maintains elements of the traditional way of life, and the spectacular Arnhem Land escarpment contains many of the best surviving examples of Aboriginal rock art. Numerous rich archaeological sites provide evidence of continuous human habitation for tens of thousands of years. Climatically, the Region is of the tropical monsoon type with a dry season from may to September and a "wet" from November to March. High intensity short period rainfall is characteristic, and the average annual precipitation is in the order of 1 350 mm. The monthly mean temperature ranges from 25° to 30°C throughout the year. The development of regulatory controls on uranium mining in the Alligator Rivers Region has been affected by the political status of the Northern Territory. While Australia is a federation, established as an independent self-governing country in 1901, it was not until 1978 that the Northern Territory became to any real extent self-governing. Prior to 1978, the Territory was administered through a special department of the Commonwealth (ie. the Federal Government). Under the Northern Territory (Self Government) Act 1978, administrative powers similar to those possessed by the Governments of the six founding Australian states were provided to the Territory Government. However, the Commonwealth government did not transfer to the Territory all such powers and functions, and in particular there has been, since 1978, a dual role for the Commonwealth and Territory Governments in the regulation of uranium development. Details of this role are provided later in this paper. RANGER URANIUM INQUIRY By 1973, major deposits had been discovered in the Alligator Rivers Region at Nabarlek, Ranger, Koongarra and Jabiluka. The estimated reserves and mine life expectancy of these deposits are given in Table I. Other radioactive anomalies have also been identified in the area but, as yet, they have not been delineated or evaluated. [ ] In 1974, an agreement was signed between the Commonwealth Government and Peko Mines Limited and the Electrolytic Zinc Company of Australia Limited for the joint development of the Ranger deposit. In July 1975, the Government announced a Commission of Inquiry under the provisions of the Commonwealth Environment Protection (Impact of Proposals) Act 1974, into the proposed Ranger development. The inquiry was known as the Ranger Uranium Environmental Inquiry or more commonly, the Fox Inquiry after the presiding Commissioner, Mr Justice Fox.

Jan 1, 1981

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By Danqing Gao, Brijes Mishra

Heterogeneity in rock formation affects both rock behavior and strength. Spatial variance of rock properties is an important characteristic of rock that addresses the heterogeneity of mechanical and physical properties and their effects on underground mining. Assessing spatial variance can be useful for locating potential difficult grounds and for performing reliability analysis in the mining support system. This study presents a spatially correlated, random model to investigate the influence of rock heterogeneity on rock strength and failure propagation. A random field database with specific spatial correlation was created for each physical-mechanical property using laboratory data and the extreme value stochastic model in MATLAB. Based on the improved microscale random model, we considered one three-dimensional numerical model to study a mine operating in the Pittsburgh seam. The influence of random field data on entry roof was investigated. The realistic random field database added two scale-measured parameters from horizontal and vertical directions to control the spatial correlation length. A number of cutting sequences were also considered in order to identify the effect of spatial variance on roof behavior. The results show that spatial variance provides an accurate prediction of erratic roof falls in coal mines.

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures by the equipment operators. As part of this effort, the U.S. National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study that determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system that was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels between outside-to-inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system’s efficiency. Tests using particle count instruments performed during nonproduction time periods on both pieces of equipment indicated protection factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By George J. Simchuk

The selection of a stripping method and subsequently, the stripping equipment, are two of the most important decisions confronting a project engineering staff during the initial feasibility study of a new coal stripping operation. The selected stripping units average from 60 to 70 percent of the total capital outlay for mine equipment and their selection will affect the type, size, and quantity of the attendant equipment, such as loading shovels, drills, haulage trucks, and bulldozers. This paper is intended to report on an in depth study by Utah's Technical Services Staff regarding the selection of stripping equipment for the Goonyella Coal Mine in Queensland, Australia. We will touch briefly, on the objectives considered in this selection; the various alternatives which were explored; the general assumptions that were followed throughout the engineering and design of an appropriate stripping system; and computations necessary to determine the amount and size of stripping equipment. INITIAL EXPLORATION Utah Development Company (presently 90% owned by Utah Construction & Mining Co. and 10% by Australian investors) commenced systematic geological studies of the Bowen Basin coal fields of Central Queensland in 1961. The Blackwater Mine as shown in Figure 1 has since been established in this area and is now producing 3.0 million tons per annum of washed coking coal. Geological reconnaissance was then extended to the northern part of the Bowen Basin and in 1963 Utah's coal prospecting area covered 2444 square miles of Central Queensland. The authority to prospect north of Blackwater has since been trimmed to 810 square miles by relinquishments to the State.

Jan 1, 1971

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987