Search Documents

By D. J. Frey

While costs of most commodities and services have increased markedly over the past 25 years, the cost of electricity has steadily declined. One of the reasons for this price decline is the improved efficiencies of generating plants which is shown in Fig. 1. 1,2 Another reason for this is the decline in coal production costs. Efficiencies for the best plant increased from about 32 percent in 1540 to about 40 percent in 1962 and then decreased slightly to 38 percent in 1965. The increase in efficiency for all plants (US average) has been even more notable, progressing from less than 15 percent in 1940 to about 32 percent in 1965. The chief reason for the improved efficiency is the change in operating steam temperatures. These increased about 12 F per year until 1200 F was reached in 1962. At this high temperature excessive corrosion of super-heater and reheater tubes was experienced and steam temperatures were dropped back to 1050 F and even 1000 F in some cases. To successfully compete against other energy sources for generating electricity, this corrosion problem must be solved so that operation at higher temperatures and thus, increased efficiencies will be possible.

Jan 1, 1967

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

By A. J. Rergis

During the past ten years a number of papers have appeared describing zeolite occurrences in the western United States in Mesozoic sedimentary rocks, altered bedded Tertiary pyroclastics, playa lakes, hot springs, and amygdaloidal basalts. With the emergence of natural zeolites as economic industrial minerals it appears, useful to develop a system of classification to delineate those zeolite deposits of economic interest which were not discovered until the middle 1950's. The first attempt at a classification of naturally occurring zeolites was made in 1914 by Lindgren l when he classified the zeolites into eleven groups based on their mode of occurrence. The zoned zeolites in the Mesozoic rocks of New Zealand and elsewhere were classified according to the mineral assemblages by Fyfe, et al.2 in 1958 as a zeolite facies corresponding to low grade regional metamorphism. In 1966, Hay suggested as an alternative to the preceding classification one which would "classify as diagenetic all mineral assemblages produced in sedimentary rocks under conditions in which zeolites are formed." In this paper a classification is proposed with the objective of providing an overall perspective of the zeolite occurrences in the western United States.

Jan 1, 1967

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By Hamed Khodadadi, Hamid Ghadiri

The ball mill grinding circuit has widespread application in mining, metallurgy, chemistry, pharmacy and research. It faces some challenges because a grinding circuit is a multivariable system in which high interaction between loops, variation of system parameters with time, and time delays are problems. In this study, a fuzzy logic self-tuning proportional–integral–derivative (FLST-PID) controller based on an improved disturbance observer is designed for control of ball mill grinding circuits. It is combined with an improved disturbance observer (IDOB) to eliminate system interaction, attenuate internal and external disturbances and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit.

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By Hal McVey

"Philosophy" addresses the definition and assigning of importance to the marketing of by-products. Two examples, one in metals and the other in industrial minerals, explore prime product to by-product relationships. Relative revenues from all products illustrate the importance of by-products to economic feasibility. "Mechanics" takes a broad view of the types of marketing organizations that are applicable to individual circumstances in the marketplace. In-house marketing as well as agents, merchants and trading companies are outlined and discussed. Philosophy Definition Of Terms Philosophy Definition Of Terms The definition of terns for a paper such as this is generally a necessary but not-very-interesting exercise. However, in simply trying to clearly define the term "by-product" some interesting relationships between products arise and the line of demarcation between "product" and "by-product" often becomes obscure. The search for that distinction represents the philosophy portion of the title. A couple of definitions of philosophy can even help to set the tone for what follows. According to Webster, philosophy is : 1 Pursuit of wisdom. 2. A search for a general understanding of values and reality.

Jan 1, 1983

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By John T. McDonough

The Climax Mine of AMAX's Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By Qing Wang

Open pit mines require substantial capital investment at the beginning of the operation and replacement investment at later years. The objective of obtaining the highest possible return on investment in a mining project can only be achieved with an efficient long term production plan. This plan consists of optimally determining four principal elements: 1) the amount of ore and waste to be mined each year, 2) the specific blocks to be mined each year, 3) the optimum mine life, and 4) the ultimate pit limits, which delineate the total reserve to be mined. The existing methodologies only provide solutions to one or two elements, by assuming the others known. Furthermore, the cost of mining each block in the deposit is assumed to be known and independent of the production schedule. The four elements of production planning are interrelated and the cost of mining any block is a function of the production schedule. The ultimate goal of this study, ,whose first steps are' discussed in this paper, is to develop a solution methodology that can simultaneously optimize all four elements of the production planning problem in open pit mines without making a priori assumption on any of the four elements.

Jan 1, 1992

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By D. C. Mahon, P. G. Sagert, M. R. Legeyt

INTRODUCTION Public opinion, over the effect of industrial development on the environment, has required government to institute guidelines for the protection of the environment both during the development of and after the decommissioning of mines. In no other area of mining has this requirement been more consistently applied in recent times than in the development of uranium mines. Uranium mines have been a focal point because of the very real uncertainties associated with the detrimental effects of radionuclides and the possible hazards of radiation. In order to determine if there is an environmental effect caused by a development or the storage of the mine waste as tailings, it is necessary to know what the quality of the environment was prior to the production of the tailings. This is the reason for baseline data programs. It is neither technically nor economically feasible to completely define the environment in any given region. Therefore, judgement decisions must be made prior to the development as to what aspects of the environment are more likely to be affected by the presence of the tailings, and to what degree. These decisions have evolved over a period of time based on information generated from existing facilities, scientific research, and the development of strong public opinions. This process is not static, but evolves with the growth of information and the technological developments which permit greater control of industrial pollution and waste management. A well-designed baseline program will reflect changes in science, technology and public attitude, even in advance of government regulations to enforce policy changes. RATIONALE FOR PREOPERATIONAL BASELINE STUDIES There are three distinct phases to be considered in the construction of an environmental assessment for a uranium mine tailings containment facility. I. Pre-operational 2. Operational 3. Post-operational (decommissioning and long term).

Jan 1, 1980

The introduction of nitro-carbo-nitrate (NCN) blasting agents has been one of the most significant innovations in the explosive industry in the last twenty years. The most commonly used blasting agent is a rather narrowly proportioned mixture by weight of 94% ammonium nitrate (AN) and 6% No. 2 diesel fuel oil (FO) that is generally designated as ANFO. Other formulations have been developed but none of these have been as extensively used as ANFO. The relative safety of the nitro-carbo-nitrate (NCN) blasting agents almost immediately suggested bulk loading techniques to obtain economies in materials handling. The first attempt at bulk handling was to pneumatically load boreholes with ANFO. When the initial experiments were made in 1957, it was apparent that there were three problem areas which needed study to minimize potential hazards. These were: 1. Static Electricity 2. Fumes 3. Safe Handling Procedures Since those early days, considerable work has been performed in evaluating these problem areas and in arriving at procedures and recommendations that would provide the required safety. Despite the relative insensitivity of ANFO type products, all normal practices for the safe handling of explosives should be obselved. Smoking should not be tolerated in the vicinity of blasting agents and misfires should be handled in the same manner as a misfire with a dynamite charge. The purpose of this Technical Report is to discuss the problems of static electricity and fumes and the solutions that have been developed. Safe handling procedures have been discussed by the Bureau of Mines and are specified by various state and local regulations. Since regulations vary from state to state, the local, applicable regulations must be followed within the area of their jurisdiction. General information is contained in a U. S. Bureau of Mines report, IC 8179, "Safety Recommendations for Sensitized Ammonium Nitrate Blasting Agents" (1963).

Jan 1, 1973

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

By Gary A. Almeraris, Thomas F. Peyton

This paper describes the innovative procedures employed during the construction of 3 deep shafts within the confines of New York City. The shafts, which varied in diameter from 1.8m (6ft) to 7.3m (24ft) and had an overall depth of 199m (650ft), were excavated by both mechanical and conventional methods. These were subsequently concrete lined, clad steel riser pipes installed and associated surface structures were constructed. Tricky surface rock blasting coupled with the unearthing of unexpected obstructions caused constant uncertainty during the excavation phase. In addition, the necessity of handling men and material in restricted yet deep openings required the development of a safer and more productive shaft construction procedure.

Jan 1, 1989

By C. L. Lin

A PC image-based, on-line instrument for the measurement of coarse particle size on a conveyor belt is under development. Both the hardware and software required to implement such a system are discussed, including the interface for the special image acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1992

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995