Search Documents

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By Pierre Ollivier, Dominique Morin, Pr. Ivo Toromanoff

Refractory gold ores have been processed by bio-hydrometallurgical process at B.R.G.M. (Bureau de Recherches Géologiques et Minières), Research Centre ,Orleans,France. The liberation of gold has been studied and the following steps for gold recovery improved. The overall process flowsheet has been established comprising different ways of treatment before the final discharge of the effluent. Iron and arsenic are successfully precipitated under well controlled Eh-pH conditions. Long term stability tests have been conducted and the research programme is to be continued with the crystallo graphic studies of the precipitates. Economical studies have been performed on the base of data obtained on parameters studies.

Jan 1, 1990

By John Ward Smith

Dawsonite bearing oil shale of Colorado's Green River Formation offers a unique and vast (6.5 billion tons of Al2O3) resource of easily extractable alumina. The processing methods required by the thermal reactions dawsonite and its oil shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary Federal oil-shale withdrawal appear less solvable.

Jan 1, 1980

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

By A. L. Mular

Si define la simulación digital y las técnicas de simulación son revisadas. La metodologia tipica conlleva la selección de modelos, el ajuste o reajuste de los datos primarios, la selección de una estrategia de acoplamiento, la valoración de la precisión del modelo en un sentido estadistico, y el desarrollo de estructura de simulación ejecutiva. La simulación sirve de ayuda para los ingenieros de procesos para evaluar la viabilidad de un esquema de flujo propuesto y el efecto de la modificación de un flujograma ya existente. Por otro lado, la simulación juega un papel importante en la optimación "off-line" y en la evaluación de estrategias de control de circuitos alternativos. Son presentados varios ejemplos para ilustrar estas utilizaciones para la simulación, incluyendo aplicaciones en los circuitos de trituración, circuitos de molienda y circuitos de flotación. Es de opinión de los autores que, dentro de la próxima década, las plantas de proceso de minerales serán estudiadas rutinariamente a través de una simulación digital durante las etapas preliminares de diseño. La simulación constituirá un importante componente en la toma de decisiones de un proceso.

Jan 1, 1982

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries' investment and production costs during the period studied.

Jan 1, 1989

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation has been a concern in hard-rock mining for the mining industry. Rock fragmentation distribution is an important index to measure the blasting effect. It not only affects the cost of drilling and blasting, but also affects the efficiency of subsequent operations, such as loading, transportation and secondary crushing.

By L. O. Bond

High costs--and high risks--are normal in coal exploration and mine development. But risks and ultimate costs are minimized by foreknowledge of prospective coal seams and adjacent formations. Extensive drill hole programs are often used to obtain needed information. Cores and cuttings from these holes are used to determine coal location, thickness, and quality; they are also used to study physical and geological characteristics of surrounding beds. Valuable as these core and cuttings studies are, their effectiveness is often diminished by loss of recovery or by incomplete analysis. Needed is an effective and economical method for augmenting these studies. Well logs provide information of the type needed for efficient cool prospecting. Furthermore, obtaining these logs in drill holes, and evaluating the data they provide, is both fast and economical. To investigate the usefulness of well logging methods in coal explorations, the authors worked with Mr. Jon Jenkins of Truax Truer Coal Company. Logs were run in a number of drill holes in various areas of the Illinois Basin; these areas provided variety both in coal quality and geologic conditions. The data were studied extensively using computer methods similar to those now used in the evaluation of oil and gas wells. (2, 3) This study was used to produce a computer-generated analysis designed especially for mining problems.

Jan 1, 1969

By Brij M. Moudgil

Flotation of fine and coarse coal after multistage addition of the frother was found to yield coal fractions with significantly lower ash content as compared to the feed. It was observed that the lowest ash content, specific gravity and reactivity of coal was associated with finer size fractions. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA) with calorimeter attachment. It is suggested that in the ignition stage, the removal of mineral matter affects the reactivity through the physical changes brought about by the ash removal. In the char combustion stage the mineral matter seems to influence the reactivity through the catalytic activity of surface concentrations of metal ions, ratio of combustible/incombustible material, internal pore structure and roughness.

Jan 1, 1984

By Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of sub-micron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and industrial waste (4) desulfurization of oil

Jan 1, 1983

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By M. Galetakis

The difficulties that rise during the evaluation of multiple-layer lignite deposits come from the deposit structure (alternating lignite layers with intercalated material of varying thickness), as well as from the limitations of the applied selective mining. Thin layers of lignite and interbedded waste layers are grouped under specified assumptions regarding thickness and ash content, to form the exploitable blocks. However, in practice the decision for excavating a block is made under subjective constraints of different importance or by using uncertain data. Advances in Fuzzy Inference Systems (FIS) have provided a new approach to the evaluation of multiple-layer lignite deposits. FIS have the ability to handle imprecise or incomplete or linguistically ambiguous information and to incorporate them into decision-making processes. In the developed FIS (Mamdani type) new linguistic variables, concerning with working conditions, operators? experience and production were involved. The FIS was used for the estimation of quality characteristics and reserves of the exploitable lignite produced from Southern Field mine, Ptolemais (Greece).

Jan 1, 2005

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By Nopadon Mantajit, Dallas W. Davis, Somsak Potisat, Prasert Kumalachan

For centuries Thailand has been a significant, though primarily unofficial, producer of gold. Panning has been the traditional way of making a living for innumerable villagers during the December to May dry season following the harvest. During this period groups can be seen working the streams, rivers, fields and dry valleys at as many as 90 localities in 28 provinces. Attesting to their efforts are the five and a half ton solid gold Buddha at Wat Trimit and much of the gold jewelry sold in Bangkok. This traditional panning will continue, and probably become more extensive, in harmony with commercial endeavors using modern technology suitable for extraction of gold from types of deposits for which gravity separation would give very low recoveries. Several such deposits have been discovered in the course of geochemical and geological surveys conducted by the Royal Thai Department of Mineral Resources with the object of contributing to early interpretation of the results of a country-wide airborne survey.

Jan 1, 1987

By M. Karmis

"The process of coal mining, as indeed of the mining of any stratified mineral, is inevitably followed by some degree of sinking of the superjacent strata and consequently of the surface." Royal Commission on Mining Subsidence, Second and Final Report, London, 1927. INTRODUCTION The above statement was used to describe mining subsidence in the classic report of the "Royal Commission on Mining Subsidence," published in 1927. In fact, this phenomenon has been recognized in Britain since the early fifteenth century, as revealed from court records of disputes and litigations related to property damage above mine workings (Shadbolt, 1978). The first attempts to investigate and analyze the mechanisms associated with mining subsidence, however, date back to the 1800's and were pursued by Belgian Engineers. This research effort was initiated as a result of the widespread movements and subsequent structural damage suffered by the City of Liege in the 1820's. The most notable achievement of the Belgian school of that era was he publication of Gonot's treatise "Loie de la Normal" in 1871 (Gongt, 1871).

Jan 1, 1982

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968