Search Documents

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By C. E. Tackett

The Greenwich Collieries Co. is a subsidiary of the Pennsylvania Mines Corporation, and a wholly owned subsidiary of the PP&L Co. which serves the northeastern portion of Pa. PP&L annually consumes about 11 million tons of coal per year and is the largest consumer of both bituminous and anthracite coal on the eastern seaboard. Development work for Greenwich started in 1969. The coarse coal plant was constructed in 1970, with the raw fines bypassed. This worked very well for our requirements at that time; however, the Greenwich mining plans were extensively changed, longwall mining units were installed and low coal was encountered, resulting in dirtier coal, a finer coal and an ever increasing ash in the shipped product. All this demanded a more efficient ash removal process for the fine coal fraction. In 1971, the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency were pushing for the now stringent sulphur emission limits at our power plants. The Greenwich Mine coal reserves contained large quantities of 3.5 to 4% sulphur along with some low sulphur reserves. It was, therefore, essential that any new plant have the capability of efficient sulphur removal to meet the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency required limits. To meet these limits our design would have to be capable of producing a product of 2.0% sulphur or less.

Jan 1, 1977

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By J. R. Brett

Utah Development Company (UDC) operates five large opencut coal mines in the Bowen Basin of Central Queensland, Australia. In total, over 20 million tonnes of coking coal are exported annually from the five mines. Typically, the coal seams dip at 5 percent, are 2 to 10 metres thick, and sub-crop some 20 to 40 metres below surface. In the main, the operations are single seam, but multiseam (2, 3 or 4 seams) operations do exist and will form an increasing proportion of the mining activities as depths increase. Draglines are used as the major stripping equipment, highwall depths currently ranging from 20 to 65 metres. Whilst project feasibilities were based on stripping to a 60 metre highwall, it is now proposed to continue opencut mining to depths exceeding 100 metres. This will entail large quantities of prestripping (ahead of the draglines) and overcoming problems associated with steepening seam dips, including haulage of coal from the pits.

Jan 1, 1982

By B. T. Lusk, J. J. Silva Castro

Currently, there are several methodologies to assess ground vibrations from blasting. Of all available methodologies, one that is becoming more important is the waveform superposition or signature hole technique. This technique is based on a signature waveform assigned to each hole to build the complete waveform for the whole production blast, using the convolution between the time initiation sequence and the signature hole waveform. In the basic methodology of the signature hole technique, the waveform hole-to-hole is assumed to be the same. Several studies and field tests have proven that the waveform hole-to-hole, even in ideal rock mass conditions (rock mass with little or no joint system), changes. In addition to distance or confinement, other factors that could change the waveform hole-to-hole include different geologic paths from the source to the monitoring point and a different energy output of each hole, due to hole loading, explosive composition and/or contamination, priming, etc. These factors result in varying waveforms generated for each hole, making the waveform produced by each hole a somewhat random process. There is available in the literature some proposals to include variability in the waveform hole-to-hole, but the parameters involved are complex and difficult to estimate. In this paper, the variability in the signature waveform hole-to-hole in a blast event was recorded through a field test, and a proposal to include signature waveform variability to develop an equation based on the Fourier series is presented. This methodology is the basis for a future signature hole analysis using a Monte Carlo scheme, taking into account the variation of the amplitude and the frequency content of the waveform hole-to-hole in a production blast event.

Jan 1, 2012

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill's approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By D. W. Park

Geologic condition is one of the most important factors for longwall mining operations, especially, the existence of faults limits the mineable area, or cause stress variations at the longwall face. Recently, a longwall panel passed through a fault at the Shoal Creek Mine of Drummond Company, Inc. The fault was situated diagonally along the longwall face and the coal seam was displaced up to 2.4 m (8.0 ft) in a mode of a normal fault. LoSCoMS (Longwall Strata Control and Maintenance System) was used for monitoring shield pressure every minute and interpreting data in terms of setting, developing and final pressures. The results of the analysis regarding the influence of the fault on the shield pressure are presented.

Jan 1, 1999

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800's was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970's influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By R. F. Korcak

There exists a wide array of industrial byproducts that produce beneficial responses in the soil/ plant environment. These materials range from clean-coal-technology residues produced during the generation of electric power (particularly those high in gypsum) to mineral fines produced by the aggregates industry (i.e., sand, gravel and crushed stone). A number of these materials are examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems are discussed.

Jan 1, 1997

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

The 31st annual American Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort on Saturday, Dec. 7, 2013. Each year, one living inductee, two Medal of Merit recipients, honorees from mining?s past, an industry partnership award, as well as a special citation, are recognized by the MFSW for their respective contributions to the mining industry. James D. Toole, past president and chief executive officer of Southwest Energy LLC, will be the Hall of Fame inductee, guest of honor, and featured speaker at the awards banquet. Toole founded Southwest Energy LLC in 1973 and is credited with introducing innovative explosive technology, providing even greater value to its mining customers. Medals of Merit will be awarded to Joseph M. Keane, principal metallurgical engineer for SGS Metcon Research/KD Engineering, and Sean D. Dessureault, associate professor at the University of Arizona. Keane is recognized for his metallurgical expertise, especially in design development and pollution abatement. Dessureault is recognized for his advanced mining research, with more than 25 journal publications, and his entrepreneurship as the founder and chief executive officer of two mineral-related companies. To honor mining?s past, the hall of fame will induct Bartolomé de Medina for his invention of the patio process for recovering silver; Ben Williams for his management of the Copper Queen Mine in Bisbee, AZ; Charles E. Mills for his contributions at Morenci and Inspiration Copper and founding Apache Powder Co. and The Valley National Bank; John S. Finlay and Edwin B. Royle for their invention of the mucking machine; and Louis Caryl Graton for his ore deposits research and teaching economic geology at Harvard University.

Nov 1, 2013

By Joseph E. Worthington

The announcement of a high-grade ore intercept near Wenatchee, Chelan County, WA, by Asamera Minerals in 1983 triggered widespread interest in this old gold mining district. The district has a long history of exploration and production and was actually one of the few underground gold mines that operated in the post World War I1 years in the US. Gold occurs in a north-trending structural zone in folded and faulted Eocene arkose intruded by andesite and dacite dikes having dates in the 42 to 50 m.y. range. Ore has been mined selectively from ladder veins perpendicular to the trend, from the south end of the trend near Squilchuck Creek. These veins narrow and silicification becomes pervasive northerly where wider zones were caved later in the operation. Recent discoveries at "B" reef at the north end are also in wide zones of silicified arkose. The gold lodes originally cropped out as prominent silicified and iron-stained ridges that were described in the early days as "reefs." The early discoveries were made in out- crop about a hundred years ago, and two claims, the Gold King and Macbeth lodes, covering the most prominent out- crops on the north side of Squilchuck Creek, were staked in 1885 and patented shortly thereafter. A five stamp mill was erected in 1894, but failed to liberate gold for amalgamation. The two patented claims were acquired in 1934 by J. Keegan, who carried out limited exploration and shipped small amounts of flux ore to Tacoma during the next few years. There was no substantial exploration or development of the claims, however, for several years after that time, and ownership of the claims eventually passed to a series of trusts administered by a bank in Seattle.

Jan 1, 1990

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By Sigmund J. Sulinski

The following is a progress report on a continuing study being made by the Sanitary District for purposes of developing reliable data for predicting costs and progress on future tunnel contracts. All data available to date on five separate tunnel contracts has been analyzed. All were machine-mined in soft ground, all used steel ribs and wood lagging and finished inside diameters varying from 5'6" to 6'6". Basic data regarding progress per shift, hours mined per shift, hours of downtime per shift, cause of downtime and type of soil mined were reported by the District's resident engineer at the job site. Figure 1, Weekly Mining Report is an example of the form used. Data regarding manpower and equipment used during tunnelling operations was also supplied by the resident engineer during the course of construction. Soil type being mined was verified by the resident engineer during construction, by visual observation, and compared with data listed on a previously prepared soil profile. The soil profile is a graphic presentation of anticipated soil stratas superimposed on a cross section

Jan 1, 1997

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983

By Kotaro Ohga, Kiyoshi Higuchi

In our laboratory, a new detection system using smell detectors was developed to detect the spontaneous combustion of coal and the combustion of other materials used underground. Laboratory experiments were carried out on several kinds of coals, including South African coals, and machine oil, wood and rubber used in belt conveyers. The following results were obtained: 1) Spontaneous combustion of coal can be detected earlier by smell detectors than by conventional CO detection methods. 2) There were no differences in the results using different kinds of coal. 3) Combustion of other materials can also be detected earlier by this system than by conventional detectors for gas and smoke. 4) Use of this detection system enables one to discern the source of the combustion gases, whether it be coal, wood, oil or rubber.

Jan 1, 1995