Search Documents

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By E. H. Cho, P. K. Dai

An acid mine drainage sludge sample, containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn, was obtained from central West Virginia. The sample was leached at room temperature with a pH 3 sulfuric acid solution. Air was then bubbled through the leach solution at pH 4.5 to precipitate the iron. The leach solution contained 258 ppm Zn, 105 ppm Ni, 90 ppm Co and 2050 ppm Mn. Three solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA. Cyanex 272 and Lix 84. The A/O ratio was one, and the extractants were diluted ten times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to a pH of 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions should be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1995

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By Raymond E. Kary, John W. Mcklveen

The four unit Cholla coal fired power station at Joseph City, Arizona, consumes coal from the McKinley mine located in western New Mexico. Since coals may contain relatively high uranium or thorium concentrations and may release quantities of detrimental progeny of these elements to the environs, there is concern that releases may pose an adverse environmental impact or even a health hazard to the workers. Thus, an effort was made to quantify the radionuclide content of the coal and compare the results with radionuclide concentrations already present in the vicinity of the plant. Additionally an attempt was made to assess any potential for significant enhancement of the levels of radioactivity in the environment or to plant personnel. Background gamma radiation measurements at and near the plant ranged from 8 to 12 [µ]R/hr (70 to 105 mR/yr) with a few localized anomolies measuring to 18 [u]R/hr (160 mR/yr). Levels on top of the coal storage piles decreased to ~ 6.5 [u]R/hr (60 mR/yr). Apparently the direct radiation emitted from the coal is less than the background levels in the vicinity of the plant. Measurements performed on top of several coal seams at the mine confirmed low radiation levels emanating from coal, but readings more than doubled when the overburden was monitored. Laboratory gamma spectrometry confirmed the lower amounts of natural radioactivity in the coal when compared against soil and water samples obtained in the vicinity of the plant and the overburden at the mine. In an effort to see if there is biological enhancement, animal feces was sampled. The radiation variations were found to be influenced primarily by naturally occurring potassium-40 which varied from ~ 1 to 18 pCi/gm rather than fluctuations in the uranium and thorium series. The potassium-40 concentrated in the ash were similar to the concentrations in the environs around the disposal ponds while Radium-226 concentrated in the fly ash was ~ 3 times that found in the immediate surroundings. Radon-222 gas concentrations in buildings at or near the plant ranged from 0.5 to 1.8 pCi/l and were generally lower than indoor concentrations measured in the Phoenix area. The burning of coal at the Cholla station does not appear to increase ambient levels of radioactivity found in the surrounding environs or to the workers. However, the use of byproduct fly ash for construction purposes may need to be examined.

Jan 1, 1981

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By F. K. Spragins

The growing demand and a diminishing supply of conventional crude oil in North America are bringing about an ever increasing interest in the so-called "synthetic fuels". With one commercial plant already in full production, another in the planning and engineering stage, and still others being seriously considered, the Athabasca tar sands is proving to be a leading center of interest. Here, and in the closely related deposits, reserves in place total over 700 billion barrels.1 This major source of new oil is about ready to play a significant role in the filling of ever increasing market demand. When and if fully developed, the Athabasca tat sands could make both Canada and the United States substantially independent of all off-shore supplies of crude for many years to come. Its product, a high-quality, low-sulphur synthetic crude, is beginning to enter the market place at a most favourable time.

Jan 1, 1972

By W. M. Luff

The Brunswick No. 12 Deposit is a large polymetallic massive sulphide deposit, occurring in Ordovician age rocks of the Tetagouche Group. Silver is contained within the sulphide zones and economically it is the second most important commodity produced. Brunswick is one of the largest silver producers in Canada. The distribution of silver within the mine is presented, with examples from various levels. The concentration of silver can be shown to be related to both stratigraphy and structure. The mineralogy of silver in mill products is also presented.

Jan 1, 1986

By Miguel Carrera, Jose Arnal, Julian Ortiz, Maarten Haest, Fouad Faraj

ShovelSense is a complete solution for bulk ore sorting at the mine face that combines robust shovel bucket mounted X-ray fluorescence sensors, with real-time material classification, fleet management integration and supporting cloud-based data infrastructure, to ensure each truck always goes to the right destination. Correct truck destinations are a challenge in many current mining settings because the material classification of a truck, which is the key input into the truck destination, is often based on estimates at block resolution (~20x20x15m), with limited adjustment for blast movement and mixing. In this contribution, we present a geostatistical, data driven approach to estimate the potential value of bulk ore sorting at the mine-face for seven open pit mines. The approach is premised on the assumption that truck loads within blocks follow a simple gamma distribution. Standard ore control data from the seven mines have been used to estimate the potential bulk sorting value at these operations and ShovelSense-integrated dispatch datasets have been used to validate these estimates for specific benches on which ShovelSense operated. ShovelSense results validate the ore control data-based value predictions and show how at mine-face bulk ore sorting value varies between distinct deposit types. In general, deposit types that have higher bulk ore grade contrasts, display more potential ShovelSense value. The manuscript concludes with the limitations and opportunities of applying the proposed value estimation approach to evaluate at mine-face bulk ore sorting opportunities for open pit operations.

Jun 25, 2023

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By Peter Amelunxen, Kain Nugent, Brandon Akerstrom, Willem Duyvesteyn, Todd Harvey

In 2024, Capstone Copper Corp commissioned a new sulfide flotation plant at Mantoverde in the Atacama region of Chile to process copper ore at a design rate of 32,000tpd. The pyrite associated with the copper ore body contains cobalt in solid solution, with Co replacing Fe in the pyrite matrix. As per the existing sulfide flotation flowsheet most of the pyrite is depressed and sent to tailings via the cleaner scavenger tail stream. A new project considers the recovery of the pyrite from the cleaner-scavenger tails via froth flotation to produce a cobaltiferous pyrite concentrate, which is then leached via the existing dynamic copper leach pad to oxidize the pyrite and dissolve the cobalt. The cobalt is recovered from the solution by treating a bleed stream of copper SX raffinate through a continuous, counter-current ion exchange (CCIX) facility. This approach to by-production of cobalt confers numerous benefits, including reduced costs compared with alternative cobalt recovery processes, reduced acid consumption in the heap leach, increased copper production, and reduced acid mine drainage potential due to the removal of pyrite from the mill tailings.

Feb 1, 2025

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By David M. Abbott

"The picture of the baby surrounded by the number of (usually) pounds of a variety of mineral products a newborn will use in a lifetime has been widely distributed over the years, both on the web and as business cards that could be distributed to anyone. Figure 1 shows a typical example. I have included a slide of the mineral baby in various lectures over the years, particularly in my lecture “Industrial minerals: much used, little recognized.” The mineral baby with associated estimated lifetime mineral quantities is updated every year. I collected a set of past mineral baby pictures to examine the changes in the quantities of the various mineral products over the years.The mineral baby was introduced by the Minerals Information Institute (MII) in 1999 and became known as the “MII Baby.” SME took over MII in 2008 and continued publication as the “MII Baby” until the merger of MII with SME’s GEM program in 2011 to form SME’s Minerals Education Coalition (MEC). MEC is now the publisher. Figure 2 is the 2016 version of the mineral baby. The repositioning of the picture of the baby from lying on its back to crawling reflects a major design change to help emphasize that SME’s MEC is now the mineral baby’s publisher.Data sourcesThe data used to prepare each year’s mineral baby comes from the National Mining Association, which collects the preliminary annual mineral commodity data from the U.S. Geological Survey (USGS) and other sources. This preliminary data becomes available late in the first half of each year. The life expectancy data for each year comes from the Center for Disease Control’s “Data and Statistics by Topic” and the population data comes from the U.S. Census Bureau’s “Quick Facts” tab.The source mineral data is compiled using metric tonnes as the basic unit. The quantity of of each mineral is the apparent U.S. consumption each year."

Jan 6, 2017

By Brianna Eiter, Max Barham, Tim Bauerle

While not well established, there is evidence that the mining industry is encumbered by several work-related fatigue risk factors. Compared to other industries, mine workers are more likely to report inadequate sleep and work longer hours per day. Given these observations, there is a critical need to identify effective ways to intervene, manage, and mitigate mine worker fatigue and sleepiness when present. One barrier to this is confusion around the similarities and differences between fatigue and sleepiness, which can result in these terms being treated as interchangeable regardless of context and make it difficult to assess and mitigate safety risk.

May 1, 2024