Search Documents

By Tatiana Kotrikova, Steven Kolarz, Alan Kolodne, James Parkes, Matthew Goff

The WMATA Yellow Line is the section of steel segmentally lined tunnels that have experienced leakage and significant corrosion in isolated areas. A three part rehabilitation design has been developed for curtain grouting, structural repairs, and corrosion protection to provide continued performance. As WMATA’s first Construction-Manager-at-Risk (CMAR) project, the design development benefitted from collaboration with the Contractor through the final design development process. Rehabilitation work started in Fall 2022 and will be completed by late Spring 2023. Details of the project, the remediation design, and the process and benefits of the CMAR approach in the design development are presented.

Jun 13, 2023

By W. G. Pariseau

This paper is concerned with the problem of calculating ground movement that occurs as a consequence of mining. Solution to this problem is straight forward in principle but rather complex in practice. The complexities of the problem arise from the ever present constraints of technology and economics. However, the identity of these constraints is often obscured by a faulty understanding of the fundamentals of the problem and a lack of appreciation of current computational capabilities and costs. As a consequence much time and effort are sometimes wasted on gathering information that is of little direct value to ground control programs while important input data are neglected. This paper therefore reviews the essentials of the process of formulating the ground movement problem. Emphasis is upon application to longwall mining, although much of the discussion applies to other mining methods as well. In many instances, the hardrock term stope could be substituted for longwall panel because the fundamentals of the problem are independent of the excavation dimensions and numerical values of rock properties. The latter affect the outcome of a calculation, of course, but not the underlying formulation. Only the major features of the problem are discussed in this brief review. The objective of the discussion is the generation of a reliable basis for developing a technically sound ground control strategy. Any rational ground control strategy must be consistent with basic physical laws. For example, under static conditions, equations of equilibrium must be satisfied. Operational, that is, tactical, details may vary widely with local conditions, but the basic approach must be based on physical laws. The alternative empirical route is intrinsically unreliable and unnecessary as well. Empirical descriptions of ground motion caused by mining including recent statistical curve fits to specialized data sets (for example, surface subsidence data) as well as antiquated "theories" of ground pressure and so forth, however dignified with mathematical formulas, are hardly worthy of the label "theory". Extrapolation of statistical data is always accompanied by rapidly diverging confidence limits, while empirical equations simply lack predictive capability under circumstances even slightly different from those of the original development. For example, applications of surface subsidence curves generated empirically in the United Kingdom to coal mines in the United States generally result in considerably greater subsidence and wider subsidence troughs than actually observed. Locally, empirical criteria for specific ground control actions may be made practical through trial and error, but such tactics are no basis for the development of a general ground control strategy. In this regard, it is worthwhile to recall the traditional scientific distinctions between speculation, hypothesis and law, between the empirical and the proven.

Jan 1, 1982

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992

By Jorge Lanza

SUMMARY La Granja copper deposit, in terms of volume, is among the five largest deposits in the world and represents reserves of three thousand million tones. The field consists of a 40 m. thick layer of copper lying over the secondary ore and further down the primary copper. The flotation process has indicated a recovery rate of 88 to 90 percent and concentrates of 27 to 32 percent of copper. The acid leaching process of low grade ore produces financially acceptable results. To carry out the project, it is necessary to build long distance pipelines and a port. Both the Feasibility Study and the Environmental Impact Study on the project have been approved by the Peruvian government. INTRODUCTION La Granja is located in the district of Querecoto, province of Chota, in the department of Cajamarca, in the Northwest of the country (Figure 1). Geographically it is situated on the eastern slopes of the Andean mountains at an altitude of 2,000 to 2,700 m.a.s.1. (Figure 1). The site is an 8 hour car ride from the city of Chiclayo, capital of the department. The first 60 km. are over a paved road and the remaining distance is over a narrow hard dirt road. The copper porphyry of La Granja was discovered between 1969 to 1971 during some geochemical prospecting activities carried out by the State mining institution, Ingeomin (currently Ingemmet). From 1978 to 1982, Ingemmet continued with its geochemical and geophysical studies supported by a German technical assistance program. A total of 19 bore- holes were drilled (5,814 m.) and a 90 m. long tunnel made. This study calculated reserves of 175 million MT. In 1993, Minero Peru drew up a technical-financial study based on the above studies and proposed a 12 year extraction operating program: 20,000 MT daily using the leaching process, followed by 13 years of operation using the flotation process with the same daily volumes. In 1994, Cambior Inc. won an international auction in order to carry on further exploration work and to have a purchasing option. Since that date the company

Jan 1, 1998

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By Bauer, Steve, Colin Goodwin, Gerald, Randy Dempsey, Courtland

"The City of Ottawa’s Combined Sewage Storage Tunnel consists of two interconnected tunnels totaling 6.2 km with a diameter of 3m including access shafts and hydraulic structures which connect to the City’s most critical sewers. This tunnel will be built 15m to 30m below ground in the downtown core adjacent to, and crossing below, the Light Rail Tunnel, which introduces additional considerations in terms of sequencing and risk mitigation. The City embarked on a unique Procurement Process to address the risks involved with a large tunnel project and those associated with tunneling below downtown, underneath and adjacent to UNESCO World Heritage Sites, and connecting to live critical sewers. This paper describes the unique procurement approach employed and the contractual risk mitigation measures developed to provide the best value while minimizing risk. Specific features include Market Sounding, using a Fairness Commissioner, Contractor Prequalification and Risk Mitigation Measures in the Tender documents. INTRODUCTION This paper describes how the City of Ottawa (the City) and the project design team developed a strategic Procurement Process and Tender that incorporated industry best practices for technical and contractual risk management for the Combined Sewage Storage Tunnel (CSST) project. The process was unique in that, while it employed a systematic review of project risks, it also solicited input from industry, stakeholders and provincial and federal partners to develop the request for Tender for this traditional design-bid-build project. Key drivers for this approach were initiated from the City’s concerns for cost control, cost certainty and overall project risk mitigation. To address these concerns, the City implemented the risk review and mitigation process right from the project design team selection. It was critical that the project design team embraced this risk management philosophy and carried it through each phase of the project. This paper serves as an excellent resource for municipalities or other owners embarking on a similar tunnel project, on how to properly apply industry best practices and the benefits of using them."

Jan 1, 2016

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduction through semi-infinite homogeneous and isotropic airway walls with convective heat and moisture transfer between their wet or dry naked surfaces and mine air with time variable temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for computation of the temperature distribution and surface temperature of the airway walls and floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. The presented solutions are derived for general conditions and they could be easily adapted to the actual ones. Results of the model represent basis for balancing heat and moisture transfer between mine air and its surrounding in deep mines under time variable temperature and humidity of the air and enable us to solve complicated dynamic changes of mine air temperature and humidity in an airway system by relatively simple mathematical tools. INTRODUCTION The importance of unfavourable influences and the costs of condition arrangements increases with mine depth. Precision demands on the methods which predict the environmental condition changes and by which it is possible to optimize condition arragements are still increasing. Environmental conditions in deep mines are determined especially by flow velocity, barometric pressure, temperature, and humidity of mine air. Therefore new and more exact mathematical models of mine air flow through airway system and those of heat and moisture transfer between mine air and individual important sources of heat and moisture are developed. The paper presented deals with description and solution of problems of heat and moisture transfer between mine air and airway walls as the rock mass is one of the important heat and moisture sources in deep mines. There are several different approaches to the problem. In some models the moisture transfer between mine air and airway walls is not considered at all. In other models the moisture transfer is described only by certain empirical coefficients. Simultaneous heat and moisture transfer is described seldom. This paper tries to describe in a simple way simultaneous convective heat- and mass-transfer processes taking place on wet naked surface of airway walls by means of corresponding

Jan 1, 1993

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By William J. Miles, Raymond E. Blair

Introduction There has been much publicity of the boom and bust in oil and gas well drilling in the US, and many comments on oil and gas gluts. Despite this, the drilling industry remains the largest consumer of functional industrial minerals. The boom years of 1981 and 1982, compared with the bust year of 1983, show a sharp reduction in the consumption of industrial minerals-1981, 7.4Mt (8.2 million st); 1982, 6.3 Mt (7 million st); and 1983, 4.4 Mt (4.9 million st). Industrial mineral use rebounded in 1984 to 4.7 Mt (5.2 million st). This was the second highest year in history in terms of wells drilled and third highest in footage drilled. Table 1 shows the history of drilling activity and mineral consumption from 1971 to 1984. The uses of functional industrial minerals in oil and gas well drilling were detailed by Miles and Blair (ME, 1983, October, pp. 1397-1400). As an update, this article addresses only the changes that have occurred in the industry in the past two-and-a-half years. It will be directed to mineral use and new products introduced to the industry. Drilling practices A partial explanation of where wells are being drilled with lower quantities of minerals consumed is: • In the boom year of 1981, there was a proliferation of number of suppliers chasing the same business. This resulted in multiple sourcing, multiple warehousing, and a huge increase in inventory that became surplus in the following years. The bust year, 1983, caused a severe shakeout in the number of suppliers of minerals and associated drilling fluids. • In 1981 and 1982, the wild speculation in the oil and gas industry led to drilling of speculative deep gas wells. Oil wells were drilled on a wildcat basis - in areas of unproven productivity. • Presently, the oil and gas well drilling industry is very active. But drilling is directed toward proven areas of production and working over old wells for increased production. This means a large number of wells are being drilled with lower average foot-

Jan 11, 1985