Search Documents

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating ex-plosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. Explosives tested include aluminum sensitized and explosive sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1978

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By Brian V. Roulston

Potash is Canada's leading industrial mineral in terms of value of production, with 11.1 M tonnes of muriate of potash produced in 1992 for a value in excess of $1 billion U.S. Each tonne of potash produced generates about 2 tonnes of waste salt, together with slimes and brine. The disposal of these waste products, particularly the salt and slimes which are discharged on the surface, has recently become an environmental concern. This concern is forcing companies and regulatory authorities to review disposal practices. In New Brunswick, on Canada's east coast, Potash Company of America operates a mine at which 2 M tonnes of potash ore and 0.5 M tonnes of rock salt are mined each year. The mine is situated in an environmentally sensitive area, noted for its dairy farming and salmon angling. In such an area it was recognized that the storage of waste on surface would be unacceptable, and the mine was designed around this principle. Three main waste streams - salt, slimes, and brine - must be managed as an integral part of the mining system. Around 1.5 M tonnes of fine salt tailings from the milling process and the rock salt screening operation, are sent directly to the active cut-and-fill potash stopes to be used as backfill. Slimes and excess brine from the mill are piped underground as a slurry to be discharged into one of the basin shaped stopes created by mining of the rock salt. While the slimes settle out, the clarified brine is withdrawn from part of the stope to be pumped to surface as a feedstock for the evaporator - a process which recovers the contained potash values in the brine. By designing a system which integrates the mining, processing and disposal of all product streams, and by careful production planning, it has been shown that zero effluent potash mining is possible and points the way for the industry in the future.

Jan 1, 1995

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Christopher J. Farrow

This paper describes the grinding circuits installed at two remote sites in northern Canada. One is Cominco's Polaris Project at Little Cornwallis Island; a barge-mounted lead/zinc concentrator. The other is Echo Bay Mines' Lupin Project at Contwoyto Lake, 400 km northeast of Yellowknife, a gold mine, all components of which had to be flown to the site. Logistics and considerations of operating and maintenance presented challenges which were met by innovative design. The evolution of the grinding circuits is discussed. Both plants are operating at design throughput.

Jan 1, 1983

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By L. Diels

About 45% of the contaminated sites are dealing with heavy metal problems. Metals are spread in the environment by mining activities, surface treatment and non ferrous processing. As heavy metals can not be degraded, removal or immobilization (leading to bioavailability reduction) are the only risk reducing measures that exist. The currently best available technique for remediation of heavy metal contaminated groundwater is to pump the contaminated water and to treat it in a wastewater treatment plant installed on the surface. Next to this often used, but expensive, pump and treat technologies, heavy metals can be immobilized by inducing sulfate reducing bacteria (SRB) to transform the sulfates, that are very often present in the same groundwater (due to the metal mining or processing activities), into sulfides. These sulfides will precipitate the metals as insoluble metal sulfides. At the moment several studies have demonstrated the feasibility of this In Situ Bioprecipitation Process (ISBP) for the removal of heavy metals from ground-water as well at lab scale (batch and column tests) as at field scale. However, some questions arise concerning the continuation of the process, the efficiency and the sustainability of the precipitates. The presented study will try to answer these questions. The study is based on more than 10 different studies, all done by the same authors, on different groundwaters and aquifer samples. The presentation will give an overview of the guidelines necessary for a correct and successful bioprecipitation process with stable metal sulfide precipitates. An important question in the ISBP is related to the sustainability of the heavy metal precipitates. It could be observed that the interruption in the carbon source delivery also stopped the in situ bioprecipitation process. Depending on the metal also some release from the precipitate could be observed. It was shown that release can occur with Co and Ni. Aquifers, on which the metals precipitated during the ISBP, were treated in a sequential extraction process under an-aerobic and aerobic conditions. It could be shown that especially under the anaerobic conditions the Zn and Cd precipitates changed from the leachable and the exchangeable fraction to the organic or Fe-Mn fraction (i.e. from the unstable to the stable fraction). The same could be observed for Co and Ni but still some fraction was present under a more available form. On the other hand it could be shown that large differences were observed concerning the heavy metal speciation on the aquifer in function of the used carbon source during the ISBP. The molasses treated systems showed a much more available heavy metal fraction on the aquifer compared to the lactate or HRC® treated groundwater. The different speciation forms based on the use of different carbon sources will be discussed in detail. It will pay attention to the influence of the carbon source, the efficiency of the induction of the bioprecipitation process, the influence on the competence between sulfate reducers and methanogenic bacteria and the influence of low pH on the ISBP. It seems that acetate, which is also a degradation product of fermentation of some carbon sources, can inhibit some sulfate reducers. Also the relation between slow release compounds and immediately available compounds will be explained. Finally a pilot study will be presented showing the problems that can be encountered during this process. Focus will be put on the induction of the process, the keeping on of the process and the follow up of the process by the installation of in situ mesocosm socks. These results will allow the correct implementation of the ISBP with an eye on longevity and sustainability of the process and present the ISBP as a much more sustainable alternative to the pump and treat technology as measure for heavy metals contaminated groundwaters.

Jan 1, 2006

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By K. N. Han, K. Peri, Y. Guan

The leaching behavior of gold in ammonical solutions with iodine as an oxidant was investigated using cyclic voltammogram and Tafel polarization. The majority of the experiments were carried out at 75°C, and the results were compared with consideraton given to the equilibrium of the iodine-ammonia system. The distribution of nine iodide-containing species at various pH values in the absence and presence of ammonia were considered at three different temperatures. It was found that, with the introduction of ammonia into the system, the concentration of iodide (I-), iodine (I2) and triiodide (I3-) is increased substantially, which in turn helps the rate of gold dissolution. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical-controlled mechanism.

Jan 1, 2002

By L. F. Barrett, D. E. Cameron, J. C. Wilson

Exploration by Anaconda Minerals Co. in the Rico area from 1978 through 1983 resulted in dis¬covery of the Silver Creek molybdenum deposit. The drill-indicated resource is 40 Mt (44 million st) of 0.31% Mo, and projections suggest that the deposit may exceed 182 Mt (200 million st). No source intrusion has been intersected by drilling, but its presence is sugested by intramineral silicic alkali-alaskite porphyry dikes observed at the surface and in drill holes. Age dates and fluid inclusion studies indicate that the deposit was formed 5.2 ± 0.2 m.y. ago and that more than 1200 (3937 ft) of cover has since been removed by erosion. The deposit is hosted by Precambrian quartzite and greenstone, and Paleozoic sediments. Three prominent faults intersect in the vicinity of the molybdenum deposit, and one of these, the Last Chance fault, strongly influenced the shape and location of the deposit. The juxtaposition of host rocks across the Last Chance fault reflects significant offset spanning at least three different periods. Wallrock alteration associated with the deposit includes potassic, phyllic, and propylitic zones in noncalcareous rocks and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Premineral faults that intersect the deposit contain the only surface molybdenum, tungsten, and fluorine anomalies. Dispersion halos of the indicator elements were defined by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1987

By Juan Andres Jarufe, Carlos Cifuentes

Numerical modelling has been extensively used to estimate plastic displacement in faults and rock mass surrounding mine excavations. Particularly, for fault slip seismicity, modelled plastic displacement is usually utilized to estimate seismic potential, however these methods assume that all the displacement caused during an specific simulated excavation step, is released as a single event at each step. This representation corresponds to a conservative estimation since rock mass displacement does not occur as one single event but as an exponential distribution of many small displacements and a few large ones. When displacement is expressed as seismic magnitude, this exponential distribution is addressed as the Gutenberg Richter (GR) relationship. This paper present a method to decompose the results from numerical models into a distribution of seismic events The reconstruction of the GR relationship from modelling displacement permits not only a more realistic approximation of the expected maximum magnitudes but also provides a tool to develop a probabilistic estimation of the maximum possible magnitudes.

Apr 26, 2022

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By R. N. Chakravorty, R. J. Kolada

Explosions of methane in coal silos and coal ships is an ever present hazard. Recent investigations have shown beyond question that considerable accumulations of methane do occur in coal storage silos and numerous recent explosions in coal transport shipping strongly indicates that the same conditions also exist in ship storage holds. Investigations have shown that the main concentrations of methane occur within the actual coal pile. Within this region normal silo and ship ventilation systems are ineffective. The main 1ine of defence is therefore to exclude potential sources of ignition or to place the coal in an inert atmosphere, or both. This paper presents the results of a methane survey of all operating silos in Western Canada. These results demonstrate that a serious and widespread hazard of explosion exists. This paper also discusses various methods by which this hazard may be reduced including methods of venti1ation, inertization, microbiological control and early warning systems.

Jan 1, 1987

By B. M. Davis

The uncertainty associated with a reserve estimate has generally been expressed as a subjective ranking rather than a quantitative expression of either reliability or uncertainty. These rankings of estimate reliability have taken a very nonquantitative bent as well. For example, the U.S. Securities and Exchange Commission definition of proven reserves is given as: Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings, or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well-defined that size, shape, depth and mineral content of reserves are well-established. (U.S. SEC, Form S-18, Item 17A)

Jan 1, 1992