Search Documents

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. Flotation responses of these minerals in the presence of potassium oleate and sodium silicate are presented and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium¬ bearing minerals such as fluorite from calcite (1,2,3) and scheelite from calcite(24) and apatite(2,5) almost always involve the use of sodium silicate, for example. The mechanisms by which sodium silicate functions as a depressant are still not understood; this fact is probably due to a number of reasons. That is, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species. (6) In addition, the type and concentration of these species depend on the ratio of Na20 to Si02, the concentration of sodium silicate, and the pH of the system. (6) At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant.

Jan 1, 1968

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By L. B. Phelps

Industrial mineral production is basic to life in these United States. Production techniques of these minerals are part and parcel of the training that mining engineering educators must, and do, impart to their students. This paper deals with the basic mining engineering program required by all accredited engineering schools and the specific way the Pennsylvania Scare University presents and builds upon them. The manner in which these concepts provide the student with the necessary tools to function as a mining engineer in me realm of industrial minerals extraction is discussed.

Jan 1, 1981

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU's based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU's considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU's. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU's and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By S. Tuylu, D. Adiguzel, A. Bascetin, E. G. Savas, O. Ozdemir

"Paste Technology has some advantages comparing to other surface disposal methods. With this method, it is possible to pump high concentrated solid materials to very long distances without segregation problem. However, it is known from Literature that pumpability of materials is completely related to rheological properties of the materials. For this reason, in this study, the rheological parameters (e.g. yield stress and viscosity values) of the paste material prepared from Pb-Zn tailings at various solid ratios (60-85%) were obtained in order to determine the pumpability of the paste material. Additionally, slump tests, which are usually used in mining industry, was carried out. Finally, regression analysis was made between the slump values and rheological parameters of the paste material to find a correlation between two independent parameters. The results showed that there is a great correlation between the slump values and the yield stress of the material. On the other hand, there was no correlation with viscosity: ty=430.28-16.877Sv (R2= 0,94; ty: Yield Stress (Pa), Sv: Slump Value (cm)). Based on the results obtained from this study, it can be clearly concluded that the slump values obtained from a simple test can be used to predict yield stress values of paste materials. INTRODUCTION Recently, surface disposal of mining tailings has become one of the biggest problems in mining industry in terms of environmental issues. Therefore, several researches have been focused on this subject in order to find a best solution or method for this problem. These studies showed that paste technology has some advantages compared to other conventional methods. Tailings thickened to the extent show no segregation of particles during transportation, and relatively small amount of settling occur post-deposition which are often called “paste” (Cincilla et al. 1997). Paste tailing technology has two applications in the industrial area as underground paste fill and surface paste disposal. Paste tailing technology was first started to be used in Grund mine, Germany in the late 1970s (Grice, 1998). Process tailing material, water and - if needed - cement materials, which are the components of the paste, must be blended to obtain a homogenous mixture suitable for pumpability. Consistency behavior of the paste material is determined using a conventional sedimentation cone concrete test (slump). Meanwhile, the slump value of the paste must be between 200 and 250 mm for surface applications (Newman et al., 2001). Additionally, in the case of underground paste system, the optimum slump value must be between 150 and 200 mm. On the other hand, the water content and density of paste at certain slump value change depending on the amount of fine particles in the tailing sample. While moisture of the material will be high, its density will be low because of surface area of particles which increases with decrease in particle size (Meggyes and Debreczeni, 2006). For pumpability of the paste to long distances, slump value of the paste must be good enough to be accepted for use of surface paste disposal. Paste material has a yield stress because they show non-Newtonian behavior and generally is classified as a Bingham plastic fluid. (Cooke, 2008; Theriault, 2003). In addition, the appropriate viscosity value of the paste along with the yield stress must be between 100 and 250 Pa (Bascetin et al., 2013; Bascetin et al., 2014; Bascetin et al., 2015)."

Jan 1, 2016

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By S. D. Bechtel

Bechtel Civil and Minerals, Inc., one of the Bechtel group of companies, is a large engineering and construction firm that services the mining industry, among others. The firm's head, S. D. Bechtel Jr., comments on how his E&C company is dealing with the recessionary economy. First, he offered a historical perspective. About a half century ago-in the middle of the Great Depression-W. A. Bechtel and several business partners drew up a fixed price bid to build the Hoover Dam. At that moment in history, the W. A. Bechtel Co. was a modest success, but the times were troubled and uncertain. Money was scarce and a lot of contractors across the country were one project ahead of bankruptcy. The bid for Hoover was a make-or-break proposition for Bechtel, and it turned out successfully. The Hoover Dam was a no-frills operation in an isolated and harsh environment. There was plenty of hard work, long hours, and not many amenities. Controlling costs was critical. Everyone knew what had to be done, and why and what the consequences were. Today's Challenge Bechtel is now a bigger, more complex organization whose management views the current economic recession as a challenge to be met in much the same way W. A. Bechtel met the challenge of the Hoover Dam: by pulling together with a sense of purpose and direction. In many respects, Bechtel's situation today has a number of parallels to that which faced my grandfather. The company is eminently successful, but times are tough and there are plenty of signs that they could get tougher. My grandfather bet on the Hoover Dam to insure the future health of his company and I think we can work together again in that same tradition, make some tough decisions together, and the company's future can be just as promising. The first and most important requirement is to make certain that everyone understands the situation. The Bechtel group of companies are in an excellent financial position now. Its workload hit an alltime high in 1982 and it is well positioned in its principal markets. But the next two years may be critical for the company. Traditionally, Bechtel's work load lags behind general developments in the economy. Although many of its clients continue to suffer serious business difficulties, Bechtel is only beginning to feel the impact. The worldwide market for basic metals remains soft; relatively low prices and abundant supplies of oil and gas have flattened the petroleum market and made once promising synfuels projects economically unattractive; utility clients are still caught in the vise between overregulation and escalating costs. And persistently high, long-term interest rates have made capital investments expensive and difficult to justify. The company maintained a healthy workload through 1982. In some areas it has had little new work and consequently has been forced to lay off some staff as projects have been canceled or concluded. In other areas new work has tided the company over and more people have been hired. But new work bookings have fallen off, creating some uncertainty for the near future. 1983 requirements are clear, although seemingly contradictory. Belt tightening and cost reduction are necessary for Bechtel to remain healthy and competitive, enabling it to handle a possible further downturn with a minimum of turmoil and dislocation. At the same time, we need to allocate resources and funds in areas that will keep us positioned for the turn-around marketplace.

Jan 2, 1983

By L. R. Todd

Gold Fields' Mesquite mine, located in southeastern California, heap leaches low grade gold ore at an annual rate of 2.7 Mt (3 million st). Ore is crushed in a two stage open circuit and belt agglomerated prior to loading on the leach pads. Since initial heap construction in October of 1985, a number of operating practices have been modified and several agglomeration techniques have been tested in an effort to improve percolation and reduce leaching time. Findings to date are discussed.

Jan 1, 1987

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017