Search Documents

By Alexander N. Winchell

The construction and erection of the Coleraine concentrating plant was commenced in April, 1909, and was completed (with the machinery installed) ready for use in 1910. Attached to the main building is 'a table house large enough to accommodate con¬centrating tables for five units and space for a small machine shop and supply store. For the handling of the' railroad cars in the upper portion of the mill there is provided on the north side of the main structure a trestle approach 650 feet long, and on the south or opposite side a tail track 300 feet long. The latter is so constructed as to permit its being incorporated directly in a possible future extension of the plant. The building, viaduct approach and tail, trestle, as well as the table house, are con¬structed of steel, the total amount used being 6,100 tons. The building is covered by corrugated' steel sheeting over 2 x 6-inch wood sheathing fastened directly to the structural steel. The north end of the trestle approach is connected with the main road-beds forming the track system for delivery of the crude ore to the plant over an embankment of a maximum height of 110 feet containing over 2,000,000 cubic yards of dirt.

Jan 1, 1920

By K. K. Bhattacharyya

In the Gulf Coast area lignite deposits occur in Texas, Louisiana, Arkansas, Mississippi and Alabama. Lignite has been mined in Texas since the early 1800's reaching a production of over 900,000 metric tons (1 million short tons) in 1910. With the availability of inexpensive oil and gas, production fall to as low as 16,000 metric tons (18,000 short tons) by 1950 (Henry, 1976). With the advent of the oil and gas shortage in early 1970, lignite production began to increase again. The purpose of this paper is to discuss the geotechnical considerations of mining lignite in the Gulf Coast area, particularly Texas and Louisiana. Lignite deposition occurs in unconsolidated sand, silt and clay environments. Extensive sand units saturated with water may be present within the potential mining depths. This paper describes the geotechnical considerations for designing a surface mine in this geographical area. These factors include geology, hydrology, mining method, and equipment utilization.

Jan 1, 1982

By Gregg Sherry, Bob Gordan

INTRODUCTION This paper report presents the general case history for the construction of the North Outfall Replacement Sewer (NORS) project. A 1982 City of Los Angeles Wastewater Facilities Plan recognized that a 19.3 km (12¬mile) section of the North Outfall Sewer (NOS), from Culver City to the Hyperion Treatment Plant, was deteriorating and had insufficient capacity. Built in the 1920s of unreinforced concrete and lined with vitreous clay tiles, the originally unventilated NOS suffered considerable corrosion by H2S gas. This caused roof tile and concrete to fall to the bottom of the pipe, which, over the years, reduced the 11.9 M3/S (420 cubic feet per second (cfs)) design capacity of the NOS to a current level of approximately 8.5 M3/S (300 cfs). This worsening condition, thereby contributing to the polluting of Santa Monica Bay. This situation culminated in the State of California Regional Water Quality Control Board, Los Angeles Region, issuing a Cease and Desist Order on January 27, 1986, which required the City of Los Angeles to eliminate such dry weather overflows through a number of prescribed actions. One of these was to construct the North Outfall Replacement Sewer (NORS) by April 1, 1993. PROJECT DESCRIPTION The NORS Project involved the construction of over eight miles of tunnel and related structures. It consisted of a main tunnel conduit to convey sewage to the Hyperion Treatment Plant and four diversion lines connecting the main tunnel to major existing

Jan 1, 1993

By W. K. Pincock

Accident prevention can be portrayed as a science that deals with facts and natural phenomena and must be dealt with in the same manner as any other operating problem. Safety at the Copper Queen Branch dates back to 1913 when a Safety Organization was started and rules formulated for underground mining. Since then the mining industry has made substantial progress in the elimination of accidents and when the Lavender Pit was started in 1951, it adopted the general plan in use at all Phelps Dodge properties. Following is a brief description of the Pit Operations:

Jan 1, 1959

By V. A. Shea-Albin

Sandstone escarpments surrounding western coal-bearing plateaus serve as critical habitat for animal species. Effects of mining subsidence on escarpment stability are not well documented; therefore, regulatory agencies may limit extraction of coal reserves underlying escarpments. Because millions of tons of this coal exist on Federal Lands, associated public revenues from Federal royalties, and valuable coal reserves, risk being lost. The U. S. Bureau of Mines is using numerical modeling techniques to analyze effects of subsidence on escarpment stability. Finite element models that incorporate bedding plane slip, gob formation, and movement along joints simulate escarpment subsidence observed in the field.

Jan 1, 1994

By Richard J. Leary

At the 1976 Annual Meeting of AIDE, Alan Merson reminded his audience that economic' success comes to those who understand things as they are, rather than as they have been or what ideology says they should be (1). He went on to say that, measured by this standard, the mining industry is in trouble. The mining firms had recognized long ago the importance of effective lobbying in Washington and the state capitals. But, he pointed out, those methods are nearly worthless anymore in coping with many land use problems because the critical decisions are likely to be made at the local level. There the tactics are far different as are the relations of the decisionmakers to the parties before then. Furthermore, in his estimation the trend is to leave land use regulation largely to the local level of government. All who are concerned for access to land for mineral development will be benefited by reading Professor Merson's paper lie is speaking effectively about the context of decisionmaking for specific cases, the shape of things in the here and now. There is, however, a longer-tern set of considerations that if pursued will be likely to foster the creation of public support for mining developments. At that sane meeting I spoke on two foundations of the long-term relationships: namely, the growth in requirements for minerals implied by projections of increasing consumption; and a rationale for fostering mineral exploration and development. I mentioned in passing the social decisionmaking process for public uses of land (2). This paper is intended as a complement. The growth of requirements for Minerals and the rationale for development based on the Entropy Law will be only mentioned. The main concern will be on the process of social decisionmaking in the context of access to land for mineral development.

Jan 1, 1976

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979

By A. Frederick Banfield

Various modeling techniques are available for describing ore deposits on the computer. Multiple seam coal deposits can be quite successfully modeled by using the variable block modeling method. In essence, this type of model provides an efficient method for storing the relevant data required for calculating ore reserves and for performing the mine planning. The main advantages of the variable block model over other methods for modeling irregular block or tabular deposits are: 1) The amount of data that has to be stored is minimal, i.e., the most efficient use of computer space is made since only the pertinent seam and topographic geometries need to be stored. 2) The computer logic necessary for calculating ore reserves and performing mine sequencing is relatively simple as compared to the logic that would be required for the three-dimensional block model. 3) A variable block model can be created either by starting from raw drill-hole data or by digitizing cross sections that contain the geologic interpretations. 4) Updating individual or multiple blocks can be performed with relative ease. 5) Display of the model is relatively inexpensive and easy to perform. The objective of this chapter is to describe a developed procedure as used in applying the variable block model to a specific multiple seam coal deposit. The general sequence of operations includes: (1) develop the computer model, (2) design the open-pit limits, (3) compute reserves, and (4) develop a long-range mining plan. The programs developed for this application are an expansion of MINTEC's MEDSYSTEM software. It should be noted that this is just one of many possible applications of the developed variable block model.

Jan 1, 1979

By Larry F. Barrett

Anaconda exploration in the Rico mining, district from 1978 through early 1983 resulted in discovery and partial definition of the Silver Creek molybdenum deposit. Approximately 44 million tons of 0.31% Mo are drill-indicated, and projections suggest that the deposit exceeds 200 million tons. No source intrusion has been intersected by drilling, but its composition is suggested by silicic alkali-alaskite porphyry dikes of intramineral age observed at the surface and in drill holes. Age data and fluid inclusion studies indicate that the deposit was formed 5.2 ±2 m.y. ago and that more than 1,200 meters of cover has since been removed by erosion. Both emplacement of the hypothesized source intrusion, and the geometry of the molybdenum deposit, were influenced by three major intersecting faults. The most significant of these, the Last Chance fault, juxtaposes Precambrian quartzite and greenstone against Pennsylvanian clastic and calcareous sediments within the mineralized zone. Wallrock alteration associated with the deposit is characterized by potassic, phyllic, and propylitic zones in non-calcareous rocks, and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Pre-mineral faults that intersect the deposit contain the only surficial molybdenum, tungsten, and fluorine anomalies. Pervasive dispersion haloes of the indicator elements were intersected at depth by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1985

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By Daniel A. Wasson

A review of the history of boosters is given with examples of the prominent types that have been made commercially. The performance and design features of protected core boosters are discussed in detail. A new gel booster is discussed with its advantages to the mining industry. Booster size, hole configuration, performance and safety aspects are reviewed. Important features of boostering in above ground and underground blasting are related to an economic analysis. This presentation will cover different types of boosters commonly used in mining. However, for the purpose of this paper a few terms need to be defined to clarify the action of different parts of a priming system. Booster* - "Any unit of explosive or blasting agent to be used in a charged hole for the purpose of perpetuating or intensifying the initial detonation". Primer* - "A unit, package or cartridge' of explosives containing a detonator or detonating cord which is used to transmit detonation to other explosives or blasting agents". Detonator - A device for initiating a detonation from a flame or a small electric current, the former being represented by a fuse cap and the latter an electric blasting cap.

Jan 1, 1981

By Edward C. Mabbs

U.S. industry must increase its productivity or lose its competitive position in the rapidly expanding and inter-dependent world markets. Recent improvements in material handling techniques and equipment, coordinated with production processes, provide one of the greatest opportunities to increase productivity. Successful managers must learn how to take advantage of these material handling opportunities to gain competitive position.

Jan 1, 1973

By Madan M. Singh

Increasingly, geotechnical data are being collected for various types of coal development projects. In many cases, a specific design concern is addressed. However, many data collection programs are not intended to immediately support mine design activities or to resolve a specific concern. The following discussion describes some current geotechnical approaches in mine planning, development of reserves, and peripheral activities. Types of Data Collection Programs Geotechnical data collection is increasingly becoming a part of standard coal exploration programs, performed along with stratigraphic evaluations and coal quality tests. The aims of such programs vary. The purpose of the exploration may be to fill out the portfolio on a block of reserves that is to be sold, leased, or held for potential future development. In such a case, a generic suite of geotechnical data are collected. The resulting engineering reports may touch on the more well known mining problems of the area, but detail may be lacking. The geotechnical data are mostly intended to enhance the saleability of the package. Mine design alternatives are generally not addressed.

Jan 1, 1985

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By C. Hanson

Two modes of potential loss of oxime extractants in liquid extraction processes for the extraction of copper have been studied. In loss "by chemical degradation, two mechanisms of acid hydrolysis are possible, some reagents degrade primarily in the organic bulk phase, Others at the interface between the organic phase-- phase protects the oxime but salts added to the aqueous acid phase can promote the rate of degradation. The reagents reported on are the LIX series (Henkel Cpn), SME529 (Shell Chem.Co.) and P5100 (Acorga) Loss by organic entrainment in the aqueous phase leaving mixer-settlers has also been studied, parameters investigated including impeller/tank geometry and the phase inlet arrangements. The consequences of extractant loss by the above mechanisms...are commented upon. They include the direct economic cost, the possible environmental problems and the implications for downstream operations such, as electrowinning.

Jan 1, 1980

By Frank A. Jerabek

Pneumatic stowing was first introduced in longwall mining in the middle twenties. Since that time it has advanced through many stages of development, particularly abroad, which have greatly improved its efficiency and contributed to its growing use. Pneumatic stowing originated in coal mining but has also been adopted in metal mining. This paper discusses the techniques of pneumatic conveying of. stowing material and equipment and applications of pneumatic stowing.

Jan 1, 1966

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

The classical slope analysis and a statistical technique were used in order to determine the iron complexes formed in the organic phase during the extraction of Fe(III) from Fe-Ni-Co sulfate solutions with Di-(2-ethylhexyl) phosphoric acid (D2EHPA) in kerosene. Equilibrium constants for the extraction based on these complexes were also calculated. The complexes determined were of the general form (Fe(OH)3-nRn?sHR)x' where n varied between 1 and 2.5 and s between 0 and 3, and both were found to be decreasing as the iron loading in the organic phase increased. Values of 1,2 and 3 were generally found for x, indicating that the complexes were monomers, dimers and trimers.

Jan 1, 1988

By Barrie A. Wigmore

There are two aspects of financing western coal development -- whether there is going to be enough money to finance the prospective large development of the industry, and the specific techniques of raising money for that development. To take the first question of whether there is going to be enough money around to finance your industry, I think it is quite clear that the restrictions on the development of western coal are going to be non- financial. Environmental impact problems are creating the greatest delay in coal mine development, at the moment; but getting enough personnel, mining equipment, railroad equipment, and failure of the Department of Interior to act on leasing federal coal lands all appear likely to create significant bottle- necks in the development of western coal -- larger bottlenecks than financing. Financing appears straightforward for the industry. There are many projections of the financing required to meet Project Independence goals. The National Academy of Engineers estimated that development of 500 million tons per annum of western coal would be necessary by 1985 to meet the Project Independence goals which might require $20 billion of capital spending. It is generally agreed that 500 million tons a year is not a realistic possibility. Carl Bagge?s estimate of production of 250 million tons a year by 1983 appears a more reasonable projection. Development

Jan 1, 1976