Search Documents

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By L. Schlink

Impacted waters, often complex, are created in mining which at some point in the mine life cycle will need to be attended. The simplest and most cost effective method of handling impacted water is to reuse it as makeup water for operations. At the end of mine life, operational reuse will not be an option and the impacted water will require treatment to achieve alternative reuse goals. Conventional mine impacted water treatment is successful in removing unwanted constituents but create brine and sludge that may require special handling or additional treatment, resulting in additional liabilities and costs. Freeport-McMoRan Copper & Gold has taken an approach to water treatment that focuses on transformation not concentration. The Water Treatment Test Facility located at Sierrita Mine has three test plants that are piloting the mine impacted water transformation process. Two plants have been designed for the removal of calcium and sulfate with products of gypsum and sulfur. The third plant removes metals from process water and transforms them into marketable metal sulfides. The transformation, rather than concentration, of mine impacted water solutes greatly reduce long term risks.

Feb 23, 2014

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By Harry G. Hedgepeth

Exploration of the Big Island trona beds by Stauffer Chemical Company started early in 1959. During the intervening time, Stauffer Chemical Company of Wyoming has developed a Large trona mine in this southwestern Wyoming area and has increased the over-all production of soda ash from natural sources by nearly one-half million tons per year. The trona, which is a hydrated sodium bicarbonate mineral, lies some 800 feet into the sedimentary rocks of the Green River formation. Present production is approximately 850,000 tons per year being extracted by means of a room-and-pillar mining system. Conventional coal mining equipment is used with some modification to accommodate local conditions. The mined and crushed ore is hoisted to the surface and processed in an on-site refinery. Refined soda ash is shipped to widely separated locations in covered hopper railraod cars. Construction in progress at Stauffer's plant will double the present capacity.

Jan 1, 1966

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By B. M. Sadashiva Murthy

Increasing quantities of nutrients and pesticides in agricultural runoff in recent years has caused the more developed western nations to become concerned about diffuse agricultural pollution. Thus, the problem of diffuse pollution is of greater importance and concern for any integrated water quality management programme. The above mentioned sources and activities causing pollution to groundwater cannot be completely avoided. The best solution is to entail a firm understanding of the principles of solute transport through porous media. The complex factors that control the movement of contaminants in porous media and the resulting behavior of contaminant plume are usually intricate to assess because of interaction of many factors such as dispersion, advection, sorption, degradation, volatilization, etc. As accurate quantification of solute under field conditions is inherently difficult, the fate of nitrate and phosphate have been analyzed in laboratory column and channel studies. From the analysis of the breakthrough curves, the dispersion co-efficient for nitrates and phosphates through sandy soil was found to be 0.262 m2/d and 0.114 m2/d for column studies, 0.321 m2/d and 0.231 m2/d for channel studies respectively. The column studies revealed that the concentration of nitrates and phosphates increased steadily in the first few days (around 5 days) and then it increased rapidly after 8 to 10 days. However, it attained equilibrium after 20 days. Similarly, the channel studies revealed a steady increase in concentration of nitrates and phosphates in the first few days (1 to 2 days) and rapid increase up to 15 days and there after it attained equilibrium. In the study, one-dimensional analytical model has been developed which include the advection, dispersion, and a characteristic term called ?total elimination rate?. The comparative study of column and channel studies, and model output (in which the term total elimination rate ?K? is considered as zero) exhibited a variation of 30 to 50 % in leaching characteristics of pollutants (nitrates and phosphates).

Jan 1, 2008

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By R. D. Hagni

Pyrometallurgical products from lime roasting of refractory gold ores, pyrite, and arsenopyrite have been examined for their mineralogy, porosity, permeability, retention of contaminant sulfur and arsenic, and potential effectiveness of gold extraction. Cathodoluminescence microscopy, supplemented by X-ray diffraction and scanning electron microscopy-energy dispersive analysis study, has shown that the products phases have characteristic cathodoluminescence properties as follows: anhydrite (CaS04), deep blue; unreacted portlandite (Ca(OH)2), deep purple; oldhamite (CaS), light yellow to rarely pink or orange; a sulfur-rich, arsenic-poor phase, violet; an arsenic-rich, sulfur-poor phase, non-CL. Within the temperature range examined (400-850°C), hematite exhibits greater porosity and permeability at the intermediate roast temperatures of 600-650°C.

Jan 1, 1993

By Y. C. Kim

This paper reviews the past 18 months of geostatistical work in a coal deposit performed jointly by the University of Arizona and the Homer City Owners. The objective of the study was to better predict the in-seam sulfur values of the deposit for the purpose of future emission control. Based on initially available 112 DDH information, variogram models were developed for Sulfur, Ash and Thickness for the entire deposit. The deposit was then kriged using 333 m x 333 m (1000 ft x 1000 ft) panel size. The estimation variance information obtainable from geostatistics was next utilized to improve the development drilling activities that were underway. The results of this effort are presented in this paper. In addition, this paper describes (1) the reasons for preferring kriging over the conventional isopachs, (2) the results of empirical validation of the kriged estimates using 19 additional DDH information, and (3) up-to-date experience on the use of conditional simulation of the same deposit for the future emission control strategy development.

Jan 1, 1980

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

By N. Arbiter

If two fluid phases are brought into contact with a solid, one fluid may completely wet the surface to the exclusion of the other, or both may wet it, forming a three-phase line of contact. These relative wetting tendencies are quantified by the contact angle 0 which is related by Young's equation (1,2) [12 cos? = 13 ? 23] [to the three interfacial tensions (3). No contact angle for the first fluid, indicating that it does not wet the solid in the presence of the second, means that the difference between the two solid-fluid fluid surface tensions, - 8 is greater than (or just 13 -23 equal to) the fluid-fluid tension 12; a finite angle indicates that the difference is less.*]

Jan 1, 1964

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.'s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010

By Harold J. Bennett

The Minerals Availability Program is a Bureau of Mines Program to systematically measure and classify identified worldwide nonfuel mineral resources according to their respective extraction technology, economics, and commercial availability. The program is designed to identify, collect, compile, and evaluate information on worldwide active mines as well as on developed and explored mineral deposits, and on mineral processing plants. Objectives are to classify domestic and foreign resources, to identify by cost evaluations resources that are reserves, and to prepare analyses of the availability of these resources for 34 commodities and secondary minerals. Availability analyses consider such factors as geographic location, the type of producible material, the technology and time required to produce a marketable product, and the productive capacity and unit cost for each deposit. These factors, reflected in the aggregated tabular and graphical data in the study for each commodity, are developed for consideration in the formulation of both domestic and foreign mineral policy. To date, the data have been collected for the 34 commodities and the availability analyses are in various stages of completion; expected first cycle completion date for all 34 is early 1986. Raw and aggregated data are available to the public in the form of computer-generated listings, tapes, and maps as well as in published reports. Also, systems developed to assist in performing the engineering and economic c analyses, including the computerized economic evaluation program (MINSIM) and the cost estimating system (CES), are available.

Jan 1, 1984