Search Documents

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By Robert D. Hansen, Basil S. Fee, Richard R. Klimpel

Despite the importance of froth flotation to the mineral industries as a means of separating various minerals, the commercial flotation reagents used have varied little in the last twenty years. Numerous articles and books are available describing existing flotation chemistry and its application, e.g., Fuerstenau (1962), Fuerstenau (1976), Aplan (1980), Somasundaran (1980), King (1982), Leja (1982), Ackerman, et. al. (1984), Crozier (1984), Hansen and Klimpel (1985). There are many reasons for this lack of significant new reagent development including the general utility and relative cheapness of collectors, such as xanthates, and frothers, such as methyl isobutyl carbinol and the glycol ethers. Another important reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials which make reliable reagent comparisons difficult and seriously limit the use of theoretically based studies to "predict" new or optimal reagents. In addition, the higher cost of "specialty flotation reagents demands that their performance attributes be significantly greater than existing general all- purpose commercial reagents – something often difficult to prove in practice. Faced with this situation, a detailed applications research pro- gram [Klimpel (1980 ab, 1982, 1984 ab), Klimpel, et. al. (1982)] was organized from 1979-1985 on mineral flotation with the following goals: 1) the development of appropriate batch laboratory flotation testing techniques sensitive enough and statistically reliable enough to identify small differences in performance between different flotation tests (i.e., between various reagents, even those with relatively minor chemical structural changes); 2) the identification of mathematical models with appropriate numbers and types of parameters that have maximum statistical power to statistically distinguish between various time-recovery profiles; 3) the generation of laboratory and corresponding plant scale data in sufficient quantity and consistency so that the highly interactive nature of the "flotation system9' of chemistry/ equipment/operating conditions could be quantified; and 4) the invention and development of really new and unique reagents for giving improved flotation performance. The goal #1 was achieved [Klimpel (1980b. 1984b), Meyer and Klimpel (1984)l by basically using a simple automated paddle device for consistent

Jan 1, 1986

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Robert B. Scott

The Dents Run Demonstration Project near Morgantown, West Virginia, was a cooperative venture involving the U.S. Environmental Protection Agency (EPA), the Water Resources Division (WRD)(1) of the West Virginia Department of Natural Resources (DNR), and the Christopher Division of the Consolidation Coal Company (CONSOL). The object of this project was to demonstrate pollution control methods and to clean up a 37.8 sq km (14.6 sq mi) watershed severely polluted by coal mine drainage. A study entitled, "Water Infiltration Control to Achieve Mine Water Pollution Control" (EPA-R-2-73-142),(2) was conducted by the Cyrus Wm. Rico Division of NUS Corporation for the grantee to determine the feasibility of utilizing remedial techniques to improve the Dents Run water¬shed. This study showed that the Dents Run watershed was discharging as much as 6,870 kg/day (15,100 lb/day) of acid; 1620 kg/day (3,560 lb/day) of iron 17,250 kg/day (38,000 lb/day) of sulfates; and 29,500 kg/day (64,900 lb/day) of total dissolved solids into the Monongahela River near Morgantown, West Virginia. This pollution was caused by the combination of borehole pump discharges from active underground mines, runoff from abandoned strip mines, and runoff from refuse dumps.

Jan 1, 1977

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By Vas P. Kenyen

Introduction Autogenous, semi-autogenous, and conventional grinding circuits are used to process ores. Current emphasis, though, is towards the use of the first two systems. The reason is the generally lower initial investment required for an autogenous or semi-autogenous circuit as compared to a conventional comminution circuit. However, the effect of operating costs that will significantly affect overall comminution economics is not considered in this evaluation. About 70% of the energy in a mineral processing plant is used in the comminution circuit. Until the 1974 oil embargo, energy was relatively inexpensive. Since that time, the cost of energy has escalated 40-fold. As a result, energy cost now forms a significant portion of operating costs in comminution. According to a survey conducted by General Electric Co. (Powers, 1982), the price of electricity will continue to rise 15% to 20% per year, in spite of the current oil glut. Both autogenous and semi-autogenous grinding circuits consume more energy than the conventional comminution circuit. Higher consumption ranging from 16% to 35% has been reported in the literature (Bassarear, 1982; Gjerdrum. 1979; Betts, 1982; and Christie, 1979). Consequently, even a small increase in energy costs is likely to have a significant impact on operating costs. Therefore, the economic decision of selecting an optimal comminution circuit is important. More than ever before, it is now critical to include in the evaluation of communition circuits not only the capital costs, but also the operating costs; in particular, the expected energy cost over the life of the operation. Failure to do this may lead to a less than optimal comminution circuit. Design A comminution system should be designed only after bench-scale or pilot plant testing of a representative sample. Conventional crushing and grinding circuits can be designed on the basis of the Bond Work Index (Rowland and Kjos, 1980). Over the years, sizing of full-scale rod and ball mills from Bond Work Index data has become well established. Autogenous and semi-autogenous mills cannot be sized based on bench-scale tests. Pilot plant tests are necessary to determine the amenability of the ore, critical size buildup, and power requirements. For this study, conventional and semi-autogenous grinding circuits were designed for ore throughput of 12, 24, 36, 48, 72, and 90 kt/d (13,200, 26,400, 39,600, 52,000, 79,200, and 99,000 stpd). Rod and ball mills were scaled up on the basis of the Bond Work Index. A two-stage semi-autogenous grinding circuit was designed on the basis of pilot plant test results. In designing a grinding system, emphasis was placed on operating flexibility. The largest commercially available equipment was

Jan 10, 1984

By R. K. Agarwal

In this paper a simple three-layered medium is considered. A circular hole is centrally located in the intermediate layer. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of [the] intermediate layer and [the] hole diameter. A comparison of stress the distribution and procedures for preparation and testing of [the] model are given. The potential of the technique is outlined.

Jan 1, 1968