Search Documents

By R. Benemelis

The existence of resins in some coal deposits in various parts of the world has been known for many years. These resins vary considerably in chemical structure and properties. The resin that is found in Utah coal, however, is rather unique, and has properties particularly attractive for the manufacture of printing ink mastics and adhesives. This resin is a rather dark, very high melting point, low molecular weight hydrocarbon resin. Its typical properties are shown in Table I. Its largest use by far, has been in the printing ink industry. The history of Utah coal resin is interesting, but unfortunately one of disappointment and failure.

Jan 1, 1990

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

By T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and sub-sieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.

Jan 1, 1987

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By M. J. Liesveld, D. Liesveld

For a Colorado mountain quarry, the Water Jet Channeling Method is far superior to Burning, Sawing, Drilling, or Shooting with Primer Cord, Water, or Black Powder. Throughout the life of our quarry, which was founded in 1947, we have used all the methods and turned to the Water Jet Channeler, which we invented and patented as our ideal way to remove dimension granite from our quarry. We jet the block on 4 sides and remove the block with plugs and feathers on the backside. The Water Jet uses approx 7.5 l/m (2 gpm) running at310,000 kPa (45,000 psi) to erode the crystals @ 1sm/h (10sf/h).The 0.533mm (.021”) nozzle oscillates back and forth to achieve an approx 5cm (2”) channel. Using the Jet, we do not lose corners or cause cracks in our red fine grain light class 5 granite.

Jan 1, 2004

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By J. H. Fowler

Canada's gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada's gypsum mining industry.

Jan 1, 1987

By Ronald J. Roman

As in every business venture, the primary objective of a mining operation is to make money for those who supply the venture capital. Therefore, all decisions concerning the operation of the mining operation should be made in light of the resulting effect on profit. The ultimate control is on profit, but the process is controlled, for example, by aiming for a recovery or concentrate grade knowing its effect on profit. The normal procedure used to determi.ne the profitability of a venture is to "present worth" all costs and incomes back to some arbitrary year zero. Every company has formed a management decision as to what it will require as a minimum return before it will undertake an investment. Once the economic analysis is completed, investment will be made only if the venture shows a positive present worth. If two alternatives are available, the alternative with the larger positive present worth is the one chosen. The same principles can be applied to the selection of a production schedule.

Jan 1, 1971