Search Documents

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

The abstract discusses the challenges of coalbed methane development in China due to low coal seam permeability. It highlights protective layer mining as a method to reduce in-situ stress and enhance permeability for improved gas drainage and disaster prevention. The study involves experimental and numerical simulations to analyze gas migration and permeability changes during stress release. It includes a stress-strain-seepage coupled test on coal, development of a mathematical model for coal seepage under mining unloading, and a numerical model based on the Wulan coal mine to explore in-situ stress release, permeability evolution, and gas drainage in an unloaded coal seam. The aim is to demonstrate the effectiveness of combining protective layer mining and gas drainage technology for gas outburst risk elimination.

Mar 14, 2022

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. Saki, J. F. Brune, J. W. Grubb

"Researchers at the Colorado School of Mines have studied the influence of headgate side ventilation controls near the longwall start-up room on the formation of explosive gas zones (EGZs) in underground coal longwall bleeder ventilated gobs. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) researchers developed a Computational Fluid Dynamics (CFD) model to study the formation of methane-air mixtures in the gob, start-up room, and bleeder entries. The relative change in size and location of EGZs are examined in response to ventilation controls in the headgate side bleeder entries near the start-up room. Modeling suggests that adjustments to the ventilation controls can be made to minimize the size of the EGZ. However the EGZ may form in or around active working areas regardless of the ventilation control settings. Research found regulators on the crosscuts into start-up room and first entry inby can force air into to crosscuts outby the start-up room causing more air to flow through the gob. INTRODUCTION Underground longwall mine ventilation systems may operate with either a bleeder ventilated gob or a progressively sealed gob. Bleeder ventilated gobs must meet the standards for safe operation of the bleeder system by examining bleeder system effectiveness. As defined in the United States Mine Safety and Health Administration (MSHA) Program Policy Letter (PPL) No. P13-V-12 (MSHA 2013), the pillared area or gob is “any area where a reduction in pillar size has occurred during retreat mining” and includes the “caved and broken material, the interstices within the caved material, and the open spaces surrounding the caved material.” The PPL further states that the intended purpose of ventilating the gob is “to protect active workings from the hazards of methane accumulations …” The requirements for operating a bleeder system as stated in The United States Code of Federal Regulations (CFR 2013) Title 30 §75.334(b) is to pass ventilation air though the gob “and to continuously dilute and move methane-air mixtures [from the gob] away from active workings and into a return air course …” where the concentration cannot exceed 2 percent methane (CFR 30 § 75.323). Further clarification of the bleeder system as described in the PPL states the following: “A bleeder system includes the area from which pillars are wholly or partially recovered, bleeder entries, bleeder connectors, and all associated ventilation control devices that control the air movement through the area. Bleeder entries are air courses designed and maintained as part of the bleeder system.”"

Jan 1, 2015

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By A. W. Easton

INTRODUCTION This presentation will address changing trade patterns in lead and zinc from the mid 1980's to the early 1990's. Lead and zinc deposits are developed where they are found in many parts of the world. As many are not in major consuming areas, there is significant international trade in both lead and zinc concentrates and in refined metal. Forecasts of mine production have been analyzed, primary and secondary refining capacity and future consumption levels have been estimated, to arrive at the changes in trade patterns expected during the next half decade. This paper will first address concentrate and metal trade patterns for lead, then for zinc, and finally some remarks will be made on captive mine/smelter agreements, on regional trade agreements, and on barriers to trade. I would like to note that. there is only a small international trade in semi-fabricated products such as zinc die-cast alloy, zinc oxide, lead oxide or rolled lead and zinc. Most of the world's zinc and lead trade is in concentrates or refined metal. LEAD TRADE PATTERNS Lead Concentrates Six countries are exporters of lead concentrates. Three countries are in the Americas - Canada, Mexico and Peru, with two in Africa - Morocco and South Africa (including Namibia), and Australia. Due to the limited growth in lead consumption and consequent minimum investment in new production facilities expected, mine and metal production levels and future consumption levels are not forecast to change much between now and 1990. Accordingly, the tonnage of lead concentrates exported will remain essentially unchanged from these six countries. In total they have exports of 480,000 metric tonnes (metal content)* and by 1990 this figure is forecast to rise only slightly with the only increase taking place in Mexico. The concentrates are exported mainly to Western Europe & Japan. Apart from these six main lead concentrate exporting nations, a significant change is expected in the United States. In the mid * All concentrate trade figures are based on metal content

Jan 1, 1986

By C. C. Jobes, J. J. Sammarco, D. L. Anderson

Computer-aided control of a mining machine places its operator in a safe, remote location, thus reducing health and safety risks. Sensing systems that provide machine position (xy coordinates) and heading (yaw) are extremely useful in aiding remote positioning of mining machines. The US Bureau of Mines (Bureau) developed two sensing systems for position and heading information: a scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system (MAPS), that employs ring-laser gyroscopes (RLGs). This paper presents a brief background and status of these sensing systems as applied to a continuous mining machine (CM). Included are field test results off each system operating in a room-and-pillar research section at a cooperating West Virginia mine.

Jan 1, 1993

By Mohammad Irshad, Larry H. Heflin

INTRODUCTION The planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. is being designed and constructed by the Washington Metropolitan Area Transit Authority. At the present time, 112.6 kilometers (70 miles) of this system is in operation and contains 21 route-kilometers (13 miles) of rock tunneling, and 14.5 route-kilometers (9 miles) of soft ground tunneling. An additional 2.4 kilometers (1.5 miles) of single track tunnels in rock are planned and 6 additional contracts will consist of some 8 kilometers (5 miles) of twin tunnel, resulting in 16 additional linear kilometers (10 miles) of single track tunnel in soft ground. The Authority plans, upon its evaluation and the recommendation of the General Engineering Consultant, to include an alternative design incorporating the convergence confinement method of construction known as the New Austrian Tunneling Method (NATM), for Sections E-5, E-6e and E-8a of the E-Route. The Metro system is constructed in a variety of geological conditions and crosses the boundary of two major geographic provinces. Rock tunneling is to the west of this "fall-line" boundary, soft ground tunneling to the east. The soft ground tunneling portions of Metro construction lie in the coastal plain which consist of a

Jan 1, 1987

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Francis F. Pitard

North America had an Important role in the early development of sampling theories. Unfortunately many progressive ideas were soon frozen into a series of guidelines based on the philosophy that "honest sampling only requires good judgment and practical experience". Such a philosophy appeared to be good enough In the early age of the mining Industry; however, it became quickly necessary to find new approaches. During the last thirty years, Pierre Gy's sampling theory provided tremendous breakthrough in the comprehension of this new science, nevertheless went unnoticed in North America. Sampling always generates complex problems and as the philosopher and mathematician Descartes suggested: "A complex problem can often be dissociated Into a series of several simpler problems, only then you try to solve those one by one". The only way to solve sampling problems is to consider each component of the overall sampling error: components of a continuous model such as long-range quality fluctuations, periodic quality fluctuations, weighting fluctuations; components of a discrete model such as materialization errors, delimitations errors, extraction errors, fundamental errors, grouping errors, and segregation errors. PAST AND CURRENT PRACTICES Many sampling methodologies have been developed, improved, and standardized during the first half of this century. Accordingly, sampling equipment has been proposed, selected, and used by standards committees. Today, there is a tremendous variety of sampling methodologies and corresponding tools offered to anyone with limited experience in sampling and it is very easy for a chemist, metallurgist, geologist or miner to spend considerable money in equipment transgressing the most basic rules of sampling correctness. Sampling stations that never worked properly in modern plants often cause engineers to abandon them and return to a primitive form of grab sampling.

Jan 1, 1986

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By Ashish Kumar, Khadija Said, Ulupi Mishra, Sekhar Bhattacharyya

Using battery-powered equipment in underground mining can improve safety, advance automation, and reduce greenhouse emissions. In this context, rechargeable lithium- ion batteries (LIBs) have a competitive edge due to their high Coulombic efficiency, superior energy density, and extended cycling stability. However, several conditions must be met for their safe operation. Their failure can cause thermal runaway (TR), which poses a significant safety risk in underground mines. Despite studies having investigated this phenomenon using physics-based models, limited research has used deep learning to predict its implications. This study aims to bridge this gap by characterizing LIB TR under dynamic airflow through simulations and predicting temperatures using two of the most common recurrent neural networks: long short-term memory (LSTM) and gated recurrent units (GRU).

Feb 22, 2026

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By W. J. Kennedy

Energy management in industry has recently achieved notice as a way to reduce costs without decreasing production. The same approach used in industry can be used in mining, even though the processes are different. This approach is based upon a three phase system of data collection, implementation, and monitoring, all aimed at gathering and evaluating information in such a way as to have a maximum impact on energy costs. This approach has these advantages: (1) attention is directed toward the part of each mining system where the most energy is used, (2) input is collected systematically from all persons involved in the operation of each system, and (3) a means of monitoring the progress toward established goals is created. The mining systems considered are truck haulage, conveyor haulage, blasting and crushing, and lighting. After describing the general procedure, the authors have described a specific method for improving the efficiency (and hence the energy consumption) of round-trip truck haul age systems.

Jan 1, 1982

By M. M. Rajkovich, J. J. Zaluski, S. J. Gardner

The telephone rings at 3:20 a.m. and an exasperated voice on the other end says, “There’s been a mine explosion at Mine No. 5 and we have not heard from three units of men!” Twenty-three minutes later, the phone rings again and another panicked voice says, “There’s something wrong at the slurry impoundment, the pool level has just dropped five feet and we’re trying to figure out what’s wrong!” Thirty minutes later, the mobile phone rings and an excited security guard says, “We have reports of thick black water running down both the right fork and left fork of Straight Creek and both seem to be rising in the banks!” As if this isn’t enough excitement, the mobile phone rings again and a stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Company No. 2 Mine, which is adjacent to our No. 5 Mine!” Is this all some kind of dream or nightmare? More importantly, however, if this could happen, what on earth do you do? Although we all like to think that “It can’t happen to me,” we all must admit that mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. Your response must be quick, cool-headed, calculated and effective. This paper will examine the issues, concerns and ramifications of this hypothetical “disaster” and then present a systematic crisis management response. While each situation is different, there are general guidelines for forming an effective plan of action.

Jan 1, 2003