Search Documents

By M. Taxiarchou

The continuously increasing rate of the non-renewable raw material consumption together with the production of immense volumes of solid wastes and effluents is one of the main characteristics of our modern society. This leads to an unconditional necessity to reduce the raw material and energy consumption and to recycle the used materials and products. Life Cycle Analysis (LCA) constitutes a promising tool in this direction. LCA is a methodology, whose main purpose is the objective calculation and analysis of the environmental burdens of products, processes and activities as well as the estimation of the possibilities to perform environmental improvements in combination with the rational use of raw materials and energy. The purpose of this paper is to present the life cycle of marble and granite from the quarrying to the processing stage, including the transportation between the quarry and the processing plant, by quantifying the environmental impacts that derive from each stage and the evaluation of their potential effects to the environment and to human health.

Jan 1, 2007

By Shahzad Moosa, John M. Pitt

Statistical variability in rock strength can be evaluated by rapid, inexpensive ultrasonic pulse velocity measurements, an important consideration since rational probabilistic design in rock is often hampered by the cost of obtaining sufficient strength data. Experimental ultrasonic pulse velocity measurements on a set of 96 limestone specimens showed two distinct statistical populations. Both populations followed Weibull distributions, with flexural strength distributions paralleling pulse velocity distributions. Thus, experimental results suggest that strength variability may be predicted from a few rationally selected strength measurements and several ultrasonic tests. The correspondence between strength and velocity may then be used to develop an experimental transformation function, allowing the development of a statistical distribution function for strength based on the known statistics of velocity. Comparison of experimental groups with full sets of corresponding strength1 velocity data showed the technique offers a fairly accurate description of the statistics of strength.

Jan 1, 1986

By Robert E. Carver

Opaline clays from central and eastern Georgia are widely used as industrial and domestic absorbants, principally as insecticide carrier and animal litter. The clays are classified as fuller's earth, although they &e somewhat atypical of the group, since opal (cristobolite) is commonly the dominant clay-sized mineral. A preliminary investigation of absorption characteristics indicated that water vapor absorption (264 days) is' related to opal content as determined by x-ray diffraction peak height ratios. Ethylene glycol vapor absorption is related to montmorillonite content. Contact absorption of water is complexly related to surface absorption, porosity, opal content and montmorillonite content, and may be as great as 112% of the original sample weight. The most absorbent clays are highly porous (to 65%) and contain both montmorillonite and opal.

Jan 1, 1972

By K. C. Kane, D. L. Meredith, B. E. Davis, D. A. Stanley, O&apos

Computer control of the minerals beneficiation process is limited by a lack of adequate sensors to provide information on the current state of the process. Recent reduction in the cost of image acquisition and powerful inexpensive computers make use of computer vision as sensory input in process control a possibility. In the phosphate industry, the amount of apatite in phosphate tailings is estimated by inspection. For machine vision, a simple 256 x 512 color image of the tailings was captured via an inexpensive color video camera on an IBM PC. Initially, the image is converted to gray scale and displayed on an EGA color monitor. A program was written which identifies the different constituents of the sample by analyzing the gray scale levels for the digitized picture. In other instances the minerals are identified by their relative color intensities. The amount of each constituent is determined with good accuracy from the area it occupies on the image.

Jan 1, 1990

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By Kostas Fytas

A computer package has been developed which is capable of evaluating alternative production schedules (long and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The package involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. The simulation model based on an iterative technique, maximizes the profits within each long scheduling period (eg. year or sixth month period), and at the same time defers stripping as long as possible. A minimum exposed ore quantity is kept at the beginning of each mining period. The final long range schedule satisfies a set of constraints for each period, mainly ore quality and quantity constraints for ore and waste. An interactive smoothing procedure at the end of each period results in a schedule that is feasible in terms of mining practice. Finally a cash flow analysis model carries out cash flow calculations so that the user can select the best alternative. The linear programming model, based on a certain number of shovel regions, defined interactively by the model user, calculates the optimum production schedule for each short period under consideration, so that a set of constraints is satisfied.

Jan 1, 1986

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By I. E. Zevgolis

A comprehensive critical review on the subject of sulfates-induced swelling behavior of lime-treated soils is presented in this study. Starting with the description of a well documented case study, the mechanisms behind the swelling behavior and the factors that affect this behavior are discussed. Then, the major experimental methods of sulfates content determination are briefly presented. Finally, an attempt is made to categorize sulfates level and equivalent risk for civil infrastructure. The paper indicates that limited work has been done, not only on identifying safe conditions for use of chemical stabilizers in presence of sulfate rich soils, but also on developing materials and methods to avoid, or at least mitigate, the problem.

Jan 1, 2008

By Shawn Boltz, Erik Westman, Derrick Chambers, Xingdong Zhaoa, Qiankun Zhua

Microseismic passive velocity tomography is becoming an effective technology for large-scale mining-induced stress monitoring in underground mines, especially in the field of early warning of mining-induced hazards. Aiming at the problems of missing low-magnitude events in traditional microseismic monitoring, as well as the potential to increase the resolution of the tomograms in both time and space, a microseismic passive velocity tomography analysis method based on the template matching method was proposed. First, the template matching method was used to pick microseismic events. Then, the probabilistic, non-linear, global-search earthquake location method was used to locate the events and calculate travel time and travel distance. Finally, the fast-marching method was used to carry out passive velocity tomography analysis to image the movement of the abutment stress associated with the longwall. The results show that the selected templates can identify more microseismic events than the traditional microseismic analysis, and the variation trend of events in each day is consistent with the data from the traditional analysis. Using microseismic event locations, travel times and travel distance can effectively complete microseismic passive velocity tomography analysis in each day during the study period and can effectively identify the forward and side abutment stress zones of that longwall panel. This study provides a reference for the identification of mine-induced high stress zones, which has implications for hazard identification and mitigation, with increased resolution of the tomograms in time and space.

Jun 25, 2024

By Carl D. Wood

Traditionally, when one considers the optimization of a flotation circuit, the scope of work focuses on a review of unit process equipment. This usually includes topics such as grinding ball typed, grind size, classifier efficiency, mill liner design, chemical reagent addition rates, alternative chemical reagents, on-line process analysis, and automated control strategy. However, since very few companies can afford the capital expenditure needed to completely automate the processes, the flotation operator remains as a critical link in optimization of the circuit. Therefore, upgrading of operator skills and knowledge through training must be considered as equally as important as unit process review. This paper will review some concepts and approaches to innovative operator training. INTRODUCTION Consider for a moment the fantastic changes that have occurred in process automation at many flotation plants during the last several years. Flowmeters, density gages, and on-stream analyzers now routinely measure process conditions and effect control strategy. These functions had until recently been entrusted to human flotation operators. Now with a little stretching of the imagination it is possible to envision a plant where very little human intervention would be required. However, when one begins to calculate the capital cost required to fully install automatic equipment, it quickly becomes apparent that many parts of flotation plants will continue to require skilled, knowledgeable operators to ensure successful operation. Additionally as these automatic systems are put into place, the operator's duties become increasingly complex. Therefore no flotation plant can be considered optimized without upgrading each operator's skill and knowledge to match the technology utilized. BACKGROUND At Henderson, one of the hardest steps towards the optimization of operators was to realize that present level of operator skill and knowledge was not sufficient. Since Henderson had a track record of producing the highest quality molybdenum concentrate in the world, it was difficult to accept the idea that change was needed, or even possible. This realization came about as Henderson began a program to modernize the cleaner plant circuit. Henderson utilizes a complex cleaner flotation circuit involving multiple stages of flotation, with a counter- current routing of flotation tailings. Since start-up in 1976 Henderson had relied upon next-day laboratory analysis techniques, that provided an after the fact measurement of process. Hour to hour process control was implemented by the operator, the basis for the operators' control decisions was primarily the individual operator's experience and "feel'. Bench marking of current flotation technology indicated that on-stream analysis was a proven state-of-the-art method for improving process control. An Outokumpu Courier 30 analyzer was purchased and installed to provide real-time analysis of critical cleaner plant flows. The analyzer quickly began to provide valuable assay information, allowing the metallurgists to develop specific target values for important flotation variables. However due to the complexity of the circuit, the analyzer information showed that a problem was usually caused when several targeted parameters went out of range simultaneously. This made it difficult for the operator to determine just where to implement the proper corrective action. It became apparent that to take full advantage of the new analyzer information each operator would have to become proficient at understanding the material balance of the entire circuit. TRAINING PLAN CONCEPTS With the goal of giving each operator a working knowledge of a circuit material balance the following concepts were applied to develop a training plan: - Most operators were high school graduates, but had fairly weak mathematical skills, and had very little experience at metallurgical calculations. - The training would have to address a wide range of topics from basic fundamentals to complex material balance. The basic sequence decided upon, was to present a fundamental topic to the entire group, break into small groups to work a “hands on'”case study example of that topic, and design the case study results so that they could be combined to highlight a major portion of the material balance concept.

Jan 1, 1993

By John C. Ferm

Although roof falls account for approximately half of the fatalities in underground coal mining, the factors that produce them are not clear. Mining methods can account for some, but in others the controlling factors are the geological setting in which the mining takes place. The present investigation was undertaken to determine the kinds of rocks that were most likely to produce roof problems. Such knowledge would be helpful to mine planning since rock samples can be obtained in advance of mining by core hole drilling. The investigation was undertaken in underground mines in the Pocahontas #3 seam in southern West Virginia and southwestern Virginia. The Pocahontas #3 is one of the most widespread in this region and is a major source of high quality metallurgical coal. There are at least ten very large mines in the area and many smaller ones. The region has a very long mining history and considerable experience has been gained in roof control problems. The study was conducted with the support of the U. S. Bureau of Mines.

Jan 1, 1978

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By R. Krishna, L. A. Kumar

The paper suggests a new empirical model for predicting mining subsidence. The parameters considered are Lithological Factor, which in this context meant percentage of sandstone, Rock Mass Factor (depending upon the RQD value of drill-hole cores), width: depth ratio and percentage extraction of coal. More than 250 drill-hole cores from seven longwall panels and 11 bord-and pillar (room-and-pillar) workings were analyzed from an extensive data bank of Singareni Collieries Company Ltd. (S.C.Co.), Andhra Pradesh, India. Excellent subsidence agreement was found with the suggested model.

Jan 1, 1993

By R. J. Miller

The current US national commitment to expanding the human presence into the solar system will clearly require major facilities in Earth orbit or possibly on the Moon. Such facilities will need large amounts of materials for structural modules, life support, propulsion and shielding. The heavy transportation costs in fuel required to lift materials from the Earth's surface make a terrestrial-based space system inherently inefficient. A more cost-effective approach would be to provide as much of the required materials as possible from other bodies in space not having the high cost of Earth launch. This paper identifies potential targets for space-based resource utilization, constraints on exploitation and relative benefits of various sources.

Jan 1, 1994

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

By P-M. Dupond, S. Lowrie, C. Tauziéde, Z. Pokryszka, A. D. Jones

A physical model has been developed to simulate the flows and mixing of gases in the waste of a longwall retreat coalface. The model is used in conjunction with computational modelling, and the distributions of permeability and gas emission in the model waste follow those in computer simulations (Pokryszka et al 1996). The physical model represents at 1170th scale a 200 m long, 3 m high coalface with a waste extending up to 280 m to the face start line. The model is tilted to the same seam slopes as the real face, e.g. 22° ascensional ventilation along the face and 7" slope to the dip. The purpose is to investigate the flow of three components: ventilation seepage flow through the waste; methane; and nitrogen injected to quell spontaneous combustion. A heavier-than-air surrogate gas (SF,) is used in place of methane, and therefore the model is inverted so that gas layers form along the 'roof". The main forces driving the flows in the waste (pressure gradients due to ventilation and the density difference of gas layers) are kept in proportion by appropriate scaling of the permeability. Calibration and validation used data from a coalface at a mine in the Lorraine coalfield. The model is now in operational use.

Jan 1, 1997

By Graham E. Rawlings

Geotechnical investigations for underground projects are subject to a variety of constraints, including factors such as accessibility, geological complexity, thickness of oberburden and finance. As a result, the extent of geological data available for route selection and assessment of underground design and construction problems may vary between wide limits. It is essential that the data collected, the degree to which it is representative, and the confidence with which the problems can be anticipated, should be reflected in the type of contract set up and the way in which the contract documents are written. The paper addresses the methods by which investigations can be focussed to make suitable overall ground assessments for feasibility level studies. Subsequent investigations can then be objectively directed toward obtaining data on specific geotechnlcal problems or aspects which impact tunnel, cavern and shaft design and construction. The extent of investigations at the preliminary and design engineering stages must be closely related to the geotechnlcal surveillance and control during excavation. Fixed-price contracts necessitate a secure geotechnical data base prior to bidding, and the provision of that to the tenderers. By contrast, 'design-as-you-go' contracts minimize the geotechnical information needed before construction, yet require immediate assessment of the excavated ground for determination of support requirements and payment category.

Jan 1, 1983

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By R. J. Reuss

Mina Maria is a high-grade, underground copper mine located in the Cananea district of Sonora, Mexico. The ore body is a massive sulfide breccia located in mountainous terrain. A major highway and an electric transmission line pass directly over the near-surface ore body. The mine is operated by Minera Maria SA de CV, a joint venture company that is 51 % owned by Empresas Frisco SA de CV and 49% by Cominco Resources International Ltd. Empresas Frisco is the operating partner. Production began in October 1990. The mining method used is undercut and fill. A continuous miner and a single-boom, hydraulic jumbo mine the ore. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation. The Maria deposit is located about 40 km (25 miles) south of the Sonora-Arizona border and 11km (7 miles) northwest the city of Cananea and the Cananea Mine. The mine portal, at an elevation of 1780m (5840 ft), is on the east side of an important drainage divide. The mill site is situated about 800 m (2625 ft) northwest of the mine on the northwest side of the drainage divide where the drainage is more favorable. Its elevation is 1860 m (6100 ft) (Fig. 1).

Jan 1, 1992