Search Documents

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By Robert C. Dunne, Maurice E. Freeman, Denis S. Yan

A laboratory tower mill was used to investigate the effect of some variables on the power requirements of a plant mill. The grinding laws were tested for fine grinding and Charles' law and Rittinger's law found to be most closely satisfy the experimental data. The effects of ball size, ball charge mass and media type were investigated. The screw speed was altered to control the power input as required. The results indicate that changes in these variables will change the grinding kinetics but in terms of the grinding efficiency they have no effect on the size-energy relationship. The main factor in the specific energy efficiency is the transfer of the input energy to the charge by variation of the agitation mechanism. The efficiency of a tumbling ball mill and a pin stirred mill were tested for comparison.

Jan 1, 1995

By K. Sasaki, T. Murakami, S. Akibayashi, Q. Wei

A numerical analysis and an experiment were done on groundwater flow past a bore hole with a cylindrical obstacle at its center. Flow around the obstacle in the bore hole was studied in detail. Two dimensional governing equations to simulate this flow were written for the hydraulic head and seepage velocity in a porous medium and for the vorticity, stream function, and velocity in the bore hole. These equations were non-dimensionalized and solved by using the alternating direction implicit and successive-over-relaxation finite difference methods. Flow visualization experiments and velocity measurements in the bore hole were done with a two dimensional model composed of a porous medium. The numerical analysis procedures were validated by a comparison of numerical and experimental results. Effects of the Reynolds number and obstacle size on flow in the bore hole are clearly shown in the velocity and streamline profiles. The quantitative relation between the seepage velocity in the porous medium and the velocity of flow around the obstacle in the bore hole also were estimated.

Jan 1, 1996

By George Munro

Heavy water inflows of up to 1350 1/sec in the 19.6 km Moawhango-Tongariro Tunnel section of the Tongariro Power Development Scheme in New Zealand gave rise to severe operating problems, particularly in the equipment stripping stage when pumping installations had to be removed. Due to the necessity to commence stripping from the upstream side the contractors. Codelfa-Cogefar (NZ) Limited, took the decision to install a steel bulkhead some 5000m in from the lower. Tongariro, portal. The article lists the considerations taken in the placement of the bulkhead, and gives details of its design, installation and final removal. A brief description of the geology of the tunnel. together with water flow sources, rates and pressures is also included.

Jan 1, 1981

By Jeffrey C. Reid

Computer processing and high resolution graphics display of geochemical data were used to quickly, accurately, and efficiently obtain impor¬tant decision-making information for tin (cassiterite) exploration, Seward Peninsula, Alaska (USA). Primary geochemical dispersion patterns were determined for tin-bearing intrusive granite phases of Late Cretaceous age with exploration bedrock lithogeochemistry at the Kougarok tin prospect. Expensive diamond drilling footage was required to reach exploration objectives. Recogni¬tion of element distribution and dispersion patterns was useful in subsurface interpretation and correla¬tion, and to aid location of other holes. Tin was its own best pathfinder. Arsenic, also a useful pathfinder element, forms a discrete halo peripheral to tin mineralization. The arsenic halo is expressed in hand specimens by asenopyrite and/or scorodite staining.

Jan 1, 1989

By Herbert M. Mandel

INTRODUCTION Designers of major public works projects in the past have displayed varying degrees of environmental consciousness, and tunnel designers in particular have always had to deal with certain environmental considerations - ventilation, lighting, aesthetics - as matters of primary design. Today, however, with a widening sector of the public becoming environmentally aware, tunnels are treated as elements of whole transportation systems, and are subject to increasing environmental scrutiny. The Route H-3 tunnels in Hawaii are examples of the time, care, and detail involved in a major rock tunnel project. Project Description The Route. Interstate Route H-3 is a proposed 10-mile highway crossing the Koolau Mountain Range on the island of Oahu, Hawaii, providing a direct connection between the Pearl Harbor area and the windward part of the island in the vicinity of Kaneohe. It is designed as a dual highway with provision to accommodate mass transit. As shown on Figure 1, the project includes two sets of twin bore tunnels (through the Main Koolau Range and through Red Hill), three highway sections of which two are through largely undeveloped mountain valleys (South Halawa and Moanalua), a viaduct, and three interchanges. From the Halawa Interchange to the Kaneohe Interchange, the proposed highway consists of two 3-lane roadways separated by a median where the highway is at grade. One lane of each roadway will not be constructed initially but will be landscaped and reserved for mass

Jan 1, 1974

By H. J. Handewith, W. D. Coski

This paper describes the development and testing of the RAMEX excavation system. Incorporating a synergy of low velocity, high energy impact and kerf cutting, this machine offers a competitive alternative to drilling and blasting in hard rock. It is a boom mining machine that incorporates the features of a lightweight roadheader and it can mine nearly any shape opening in hard rock. The RAMEX Tunneler has been developed to satisfy industry demands for a non-explosive, flexible, continuous and rapid underground rock excavation system. It will produce minimum ground vibration in the urban environment and allow the flexibility necessary for thin seam mining conditions. It will also reduce initial ground support costs and has a minimum impact on rock integrity. Developed by RAMEX Systems with cooperative research provided by the U.S. Bureau of Mines, this system, could produce the next step in the continuing evolution of mechanical mining systems.

Jan 1, 1989

The following list is a representative sample of the types of software available to the mining industry. For additional information concerning software packages for your minicomputer, contact equipment manufacturers or software suppliers.

Jan 11, 1981

By J. M. Velazquez, J. H. Meza Viveros

This paper describes some of the parameters and technologies used at the Mexicana de Cobre smelter, and discusses the principal design parameters and new technologies that are being implemented in a smelter-expansion project designed to increase the production capacity of anode copper from 180 to 300 kt/year (200 to 330,000 stpy). In addition, some parallel projects under construction in the smelter plant are described.

Jan 1, 1999

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By G. W. Luxbacher

Acid rain legislation included in the Clean Air Act Amendments of 1990 caused a great deal of uncertainty regarding the price, source and production quantities of coal supplied to the eastern coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward. South American coals move into the northern markets. States are proposing legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries. Some utilities question the long-term availability of eastern compliance coal. Major coal producers must make decisions now to assure their continuing presence in the market place. Several companies have adopted a strategy to acquire eastern compliance reserves, while others have invested in technology to compete as a low-cost producer. Legislation "Acid rain." This is a topic that was debated within the scientific, environmental and industrial communities for years. Those discussions resulted in a large outlay for the federal National Acid Precipitation Assessment Project (NAPAP), which was then ignored. Acid rain then became the subject of a "60 Minutes" broadcast that debunked the acid rain theory, supporting the NAPAP study conclusions. In the final outcome, however, acid rain was the driver for the Clean Air Act Amendments of 1990.

Jan 1, 1992

By Lane White

Ninety-seven papers were presented at the Mine Ventilation Symposium's technical sessions. Following are brief summaries of topics covered in this wide-ranging program.

Jan 1, 1993

By Fred Leighton

Miners have long known that rock noise, or the popping and cracking of the rock commonly heard during mining, can indicate instability of the mine structure. For many years, miners have "listened" to the rock talk and many times have interpreted changes in rock noise activity to be a warning of failure and have retreated from the potential failure area. Microseismics, or the study of rock noises, was begun in the early 1940s partly because of this historical fact. Microseismics is based on using geophysical equipment to detect and analyze rock noises on audible and subaudible levels. Thus, these systems are much more sensitive than the human ear and "hear" even more of the rock "talk" than do miners. Research has shown that micro-seismics can be used to precisely locate portions of a working area that are generating rock noise, and that rock noise release rate information from each area can be used to analyze its stability. On the basis of research results, microseismic systems are now commercially available and have been purchased and installed in many mines around the world. Introduction When a rock mass is subjected to changing stress conditions, such as those caused by mining, small-scale adjustments occur within the rock that release seismic energy. When this energy is in the audible range it is called rock noise. Those areas where stress changes occur are also the areas of the structure most likely to fail. Individual rock noises can be detected and analyzed to determine their precise location relative to the mine structure. Over a period of time plots of this data provide a pictorial representation of where stress changes are occurring. This is because rock noise activity tends to concentrate in those structure areas most actively adjusting to the changing stresses. Since these areas are the most likely to fail, they can be pinpointed and mapped relative to the structure. Rock noise rates, or the number of rock noises occurring per unit of time, also tend to vary dramatically before failure. Thus, the ability to locate the source of individual rock noises provides a means of determining where failure may occur, and rate counting within each area offers a means of assessing when failure may occur. This information, properly treated, can be used to avoid, control, or warn of impending failure. Successful applications of this technique have provided recent impetus to the effort of developing microseismics into a practical, reliable, and economically feasible tool. The phenomenon of naturally occurring rock noise was discovered in 1938 by Obert and Duvall (1939) who were measuring seismic velocities in mine pillars. Seismic energy other than what they were generating continually registered on their recording equipment. Further study by these researchers showed that the extraneous seismic energy being recorded was from rock noises that were being generated within the rock in highly stressed areas. Pursuing this interesting phenomena both in the laboratory and in the field, Obert and Duvall documented the dramatic change in rock noise rate before failure (Obert, 1941). They also established the fact that, in many instances, rock burst failures could be predicted by monitoring and listening to the rock noise activity in rock-burst-prone areas (Obert and Duvall, 1945). These early efforts clearly showed that microseismics had great potential as a tool for measuring or estimating mine structure stability. Extended testing, however, showed that sometimes rock bursts occurred with no apparent microseismic warning, and that at other times sharp increases in microseismic data were not accompanied by failure. Also, because precise location of individual rock noises was not possible at that time, one never knew where the failure was going to occur, only that failure near the observation point was likely. Thus, while the technique clearly offered promise, it was not considered practical then. In the mid-1960s, the Bureau of Mines undertook a new research effort to improve the microseismic technique. Major improvements were judged possible mainly because new and vastly improved electronic and system components had become available as an offshoot of space program instrument development. Thus, in 1967, development of a multichannel, broad band, microseismic system began (Blake and Leighton, 1970). Application of this system in rock-burst-prone mines showed it worked well and provided the incentive to develop methods whereby the source location of individual rock noises could be easily and directly calculated (Leighton and Blake, 1970; Leighton and Duvall, 1972; Redfern and Munson, 1982). The improved system and the ability to locate rock noises quickly showed that the microseismic technique offered new and increased poten-

Jan 8, 1983

By Edwin J. Connell, O&apos

Investment in mining and related process facilities will be more costly and complex in the 1980s than ever before. Interest rates and inflation are soaring; regulations are expanding; and in order to achieve economies of scale, plant facilities and mines are getting larger. As the pace quickens, the time/cost circuit closes around the resource owner or developer. Larger modern projects cost more money and take more time to build. The longer it takes to bring a project onstream, the more it costs in interest, escalation, and lost production. One solution to the time/cost squeeze is to take advantage of systems developed by major contractors serving the mining industry. These contractors have been serving clients in planning and executing large and small projects for many years. They have developed systems which, if applied at an early point in the project's life, can be a significant benefit in development of mineral resources. The systems involve performance of feasibility studies, economic evaluations, and the project installation itself. First the Feasibility Study Feasibility studies can minimize risk through systematic evaluations while progressing toward the ultimate objective-an operating plant. Normally, studies are initiated with a minimum amount of specific information and a maximum number of as¬sumptions. Through the course of the study program, assumptions are continuously confirmed, refined, or rejected by facts until a sound basis for decision is available. High on the list of cost effective tools for evaluation is the use of a geostatistically derived sampling program that provides a highly accurate ore reserve estimate for economic evaluation. When a predetermined sample of data from the drilling program and bench-scale or pilot-plant tests are received, a detailed feasibility study may be started. This study can involve design of the mine,

Jan 10, 1980

By Ferdi Camisani

The ‘Bible’ 1977 & 1981 ‘South African Mine Valuation’ by C. D. Storrar. Proved reserve (=’measured ore’ USA; ore reserve = the payable portion of the proved reserve) -Fully developed (…immediately available…) -Partly developed (…not immediately available…) -Undeveloped (…unavailable…) Probable reserve (=’indicated ore’ USA) Possible reserve (=’inferred ore’ USA) Life-of-mine reserve (Proved + Probable + Possible)

Jan 1, 2003

By Barry T. Kilbourn

Yttrium Oxide is versatile; it is essential for television phosphors, for microwave garnets, for laser crystals and for high-performance ceramics, to name but a few advanced applications. When produced commercially, the material must satisfy not only stringent specifications regarding chemical purity but, increasingly, also meet closely defined physical parameters. The techniques needed for its production range from solvent extraction to carefully controlled precipitation and calcination. The processing steps from mineral concentrate to pure oxide will be described and related to the final oxide. The simple word "material" has complex connotations; it means, to paraphrase "Alice", exactly what we want it to mean. Throw in the label "advanced" and the picture darkens further! Just what is an advanced material and how does it differ from a common-or-garden material?

Jan 1, 1990

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

The responses of calcite, feldspar and quartz minerals in a laboratory free-fall electrostatic separator after tribocharging with stainless steel, PVC and copper plates were investigated. The effects of H3BO3 and BaC12 chemical pretreatment on the electrical properties of the above minerals were examined. The changes in the electrical properties are discussed along with the determined charge, dielectric constant and electrical conductivity of the mineral samples. The electrical properties of the minerals and their responses to the electrical field during separation after tribocharging and chemical pretreatment are explored relative to the electrical behavior of the minerals.

Jan 1, 2000

By V. Y. Kirillin, V. A. Rumjantsev, S. A. Tchesnokov, Yu A. Veksler, V. F. Kalmykov, A. N. Telgarin, A. T. Shakirov

Mining in outburst hazard seams may be safe and effective if some preventive measures, such as lowering gas and rock pressure as well as speed regulating of a continuous miner in cutting the seam would be practised. The driving speed should be optimal as the low speed lowers labour productivity but the high speed may cause gaso-dynamic phenomena. At this mine the driving speed is regulated by seismo-acoustic control of the seam condition.

Jan 1, 1985

By Frederick H. Parkinson, Joseph Fernandez, David E. Westfall

The April 13, 1992, flooding in the freight tunnel network under the city of Chicago had a profound effect on the nearby Chicago Transit Authority (CTA) subway service. This paper provides an overview of the evaluation techniques, mitigation measures, and water control efforts used to maintain the integrity of the subway tubes. Specific topics discussed include visual inspections, inflow monitoring, structure and soil testing and sampling techniques, and the development and implementation of chemical and cementitious grouting programs.

Jan 1, 1993

By T. Tamagawa, S. H. Tabaian, I. Iwasaki, N. X. Fu, M. Kobayashi

A gaseous chlorination process for the hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low-temperature chlorination -selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the process is described. Initially, the chlorination behavior of chalcopyrite concentrate micropellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established were used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 2000