Search Documents

By O. M. G. Newman

The Electrolytic Zinc Company of Australasia Ltd., generates a jarosite waste at its Risdon smelter. Since 1974 this waste has been disposed of at sea off south-east Tasmania. As part of a monitoring programme prescribed by the Australian Government, bottom sediments from the disposal zone are monitored regularly. QEM*SEM image analysis complements conventional chemical analysis, having the ability to partition the occurrence of an element between sediment particles of metallurgical and natural origin. The adaptation of QEM*SEM techniques to the evaluation of bottom sediments provides insight into the fate of the particles of jarosite waste.

Jan 1, 1989

By Hu Wenjun, Li Maonan

Mine ventilation systems mostly are ventilation networks with fixed-quantity branches. The solution to the problem of ventilation networks with fixed-quantity branches is obtained by choosing the fixed quantity branches as chords and using Hardy Cross iteration method. The solution usually is feasible but may be not economical. This paper takes minimal annual ventilation electricity cost as an object, considering the power of main fans and boosters, natural ventilation pressures and resistances of regulators, and builds up a nonlinear programming model. A set of initial values of the nonlinear programming can be obtained by using Hardy Cross method, The MAP technique then used to find a set of local optimal solution The running procedure with a simple example is dicussed. Mine ventilation systems mostly are ventilation networks with fixed quantity branches. In the networks, air quantity of branches are generaly regulated by increasing branch resistance or air pressure. A comon approch to the of the networks with fixed quantity branches is to formulate it based on Kirchhoff's current and voltage laws and the solution is obtained by Hardy Cross iterative technique. The solution usualy is feasible but may be not economical. The optimal plan of air quntities regulation of mine ventilation network should be to make the solution satisfy both required quantity of work places and minimal ventilation operating cost. It is the purpose of this paper to introduce a new approch and computational experience of nonlinear programming of the optimal problem.

Jan 1, 1991

By Felicia F. Peng, Victor Z. Sun, Syd S. Peng

A probability-based analysis method in conjunction with the finite element structure modeling technique to evaluate an entry system stability is developed. Variability of the rock properties and loading surrounding the entry system is taken into consideration to predict a roof stability by using the probability of failure instead of the common safety factor concept. A dynamic programming is applied to establish a recurrence relationship between the degree of potential roof fall and accumulated roof fall index in an area of interested. A probable distribution of roof fall is assessed by using a developed computer program, RFSTAB. The assessment of the roof falling boundary in the longwall entry system is used as the example to illustrate the procedure and effectiveness of this analysis method

Jan 1, 1996

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By C. F. Bonney

Spherical or oil agglomeration has been recognised for many years as a possible process for the recovery of mineraVmetal values. BP has investigated the potential of spherical agglomeration for a number of minerals as have other workers. Testwork has also been carried out by both BP and others on the selective agglomeration of fine coal. The spherical agglomeration of both minerals and coal depends on the use of an immiscible liquid e.g. a hydrocarbon which is added to a suspension of the solids in water. On agitation the oil is distributed over oleophilic/hydrophobic surfaces and particle impact allows inter-particle liquid bridges to form causing agglomeration. It is also possible to enhance the oleophilicity of the material to be recovered by the use of collectors similar to those used in froth flotation.

Jan 1, 1998

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By Gus Van Weert

Capital and operating costs for a 10 tpd NITROX PROCESS® demonstration plant are being established. The flowsheet is based on Dickenson Mines' Red Lake arsenopyrite concentrate. Support for the work comes from a number of mining companies, engineering firms and the Northern Development fund of the Ontario Government.

Jan 1, 1998

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

By Gregory A. Hahn

Explorationists and engineers rarely speak the same language. Explorationists are not cognizant of the information that engineers require to make the appropriate choices and decisions. Engineers can- not "translate"geo1ogic parlance and data into information relevant to proper decision making. This often creates a physical and intellectual "rift" between engineers and geologists that inhibits a smooth transition to development. A transition team leader who is grounded in both disciplines can best facilitate integration and communications between the explorationists, who understand the intrinsic attributes of a given deposit, and the engineers, who have to design for extraction and beneficiation of an orebody.

Jan 1, 2001

By Juan P. Camus

One of the most important decisions in mine development is the selection of the mining method. Open pit or underground methods are selected depending on the shape of the deposit, and its position with respect to the surface. When the decision is not clear or evident, then the common rule is to compare underground and open pit projects to choose the one which yields the maximum return. However, in some circumstances' the best alternative is to start-up the operation with an open pit until a point where mine operating costs make more convenient to employ an underground method. In this case, the final pit limit is not directly related with commodity prices and its position is a funtion of capital and operating costs associated with both methods. The goal of this paper is a mans of establishing the proper ultimate pit considering a potential underground mine. The methodology is quite simple and can be implemented to work with a variety of available routines for pit optimization, such as Lerchs-Grossmann, floating cone, network flow and the Lemieux moving cone optimizing algorithm, which is the tool used by the author.

Jan 1, 1992

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By Daniel Tempelis, Tom Freeman, Eric Fordham, John Shamma, Steven Duke

The Arrowhead Tunnels in southern California are being completed by MWD under stringent groundwater in?ow limits established by the U.S. Forest Service. Pre-excavation grouting, new TBMs and a bolted, gasketed, pre-cast concrete segment initial lining are employed to control water in?ows. The effectiveness of prescribed water control measures was analyzed using conservative assumptions with the analytical techniques described by Goodman (1964), Heuer (1995), and numerical modeling. Analyses results suggest groundwater in?ows to the tunnels can be maintained well below the limits with aggressive pre-excavation grouting balanced against a reasonable rate of advance and quality erection of the initial lining system.

Jan 1, 2003

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Since 1982, the US Bureau of Mines has investigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (=1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars be provided only in mines =1.07 m (42 in.). However, court obtained variances are granted to mines =1 .22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1990

By P. M. Godinho

The debut of the sustainable development concept in the political arena, and the publication of Our Common Future in 1987, represents the starting point of present concerns and efforts associated with the sustainability of the ecosphere and its ecological and human subsystems. The sustainable production and consumption of natural resources, in particular mineral resources, represents a central aspect of the problem. In this context, an important goal has been to develop sophisticated management systems, which consider sustainability principles, in organizations within the system of minerals and metals (SMM). The development of indicators is only part of this challenge. The extractive industries (EI) as an important stakeholder of the SMM (should) have similar priorities. If embraced, this challenge offers great opportunities, one of them being the potential for advancing the understanding of how these organizations learn and change. The identification of its main determinants offers, in theory, the possibility for their management and a faster achievement of the sustainability levels to which they (should) aspire.

Jan 1, 2007

By R. A. Pindred, M. P. Lam

Cyanide is a conventional lixiviant for gold extraction but its' toxicity is a major concern for the environmentalist. There are many alternative non-cyanide lixiviants, such as thiourea, thiosulphate, chlorine and hypochlorite etc., which may reduce environmental sensitivity. This paper will discuss the leaching characteristics of gold in hypochlorite leaching solutions. The dissolution of gold in a hypochlorite solution not only depends on the concentration of the hypochlorite but also on other variables, such as hydrochloric acid, sodium chloride and temperature. The dissolution rate of gold in hypochlorite solution is much faster than other lixiviants. Due to the interference of impurities, gold extraction from an ore under ambient conditions requires large quantities of reagents. However, refractory gold ores may be successfully pressure oxidized in an autoclave at reasonably low reagent levels. Gold extraction to the pressure oxidation leach solution is rapid and complete in one stage, thus eliminating the need for further cyanidation.

Jan 1, 1990

By Gary F. Meenan

Continuous pi lot scale dewatering tests compared the performance of the vacuum disc filter with that of the screen bowl and the solid bowl centrifuges. The test results allow the a priori prediction of plant product moisture based on the feed particle size. This information is useful for selecting the best dewatering device for a given size material and for optimizing the dewatering performance of existing plant installations. Quantitative information was gathered on the ability of filter aids to improve the filtration rate of fine coal slurries. A polymeric flocculant and oil were added to the disc filter feed material at various dosage levels. Both filter aids increased the disc filter output. For the coal tested, the flocculant filter aid achieved higher filtration rates at a lower cost.

Jan 1, 1988

By J. Kircher

Nevada Goldfields' Aurora Mine consists of a 270 mtpd (300 tpd) precious metals mining and milling facility located 28 miles southwest of Hawthorne, Mineral County, Nevada and lies within five kilometers of the Nevada-California border. (Figure 1) Ore production presently is derived 85% from an open pit source with the balance from underground. The Aurora Mill is a compact conventional cyanide plant utilizing a carbon-in-leach extraction process followed by stripping of loaded carbon and electrowinning at Nevada Goldfields Kingston Mine, located near Austin, Nevada. Production commenced in December 1987 and annual gold production is currently 20,000 troy ounces of gold and 22,000 troy ounces of silver per annum, produced at an average cash cost of $178 per ounce of gold. Tailings handling at, Aurora was originally accomplished using a belt filter press producing a solid cake that was then transported to a final storage area. Although overall operating costs at the mine were' in the lower percentile of producing gold mines, the tailings handling portion of the operating costs were inordinately high.

Jan 1, 1989

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By J. Duarte Neto, V. M. Torres, A. Viana, G. S. P. Pereira, P. M. Andrade

There are technical and commercial limitations to using high fluorine copper concentrates in industrial copper smelters. The presence of more than 1,000-ppm fluorine affects the sulfuric acid units generally integrated to copper smelters. Price penalties are normally applied to copper concentrates with high fluorine contents. Several process alternatives to resolve this issue were studied at the Companhia Vale do Rio Doce (CVRD) Technology Center, Santa Luzia, Brazil. These alternatives included modifications to conventional sulfuric acid plants so that they can use high fluorine concentrates; removal of fluorine-containing minerals by flotation using depressants; selective leaching of fluorine minerals; and sulfuric acid leaching of the copper concentrates. As a result of this research, a hydro¬metallurgical process to remove fluorine and upgrade copper concentrates was developed by the CVRD.

Jan 1, 1999

By Karl-Heinz Bruemmer, Karl Wollers

1- Importance of Shafts for the Exploration and Extraction of Coal Deposits Coal mining in the Federal Republic of Germany is carried out in a depth between 800 and 1200 m below sea level (Fig. 1). The shortest connections underground in a mine and up to the surface are vertical shafts. Such shafts assume, with ventilation, manriding and the winding of material, the most important functions for the maintenance of mining operations. In the German coal mining industry, a difference is made between the main shafts providing a direct access from the surface to the deposits, and the so-called "blindshafts" which serve as a connection between two or several haulage levels underground. [ ]

Jan 1, 1976