Search Documents

By Guoming Liu, Weibai Hu

The designing aspects of column profile, cross-section and height, types of aerator or air sparger, and feeding and discharging devices have been designed and tested. In operating aspects, the flotation column: has beer, compared with the conventional mechanical flotation machine in large- scale plant practice. It has been found that the reagent conditioning time and the slurry residence time required in the column are longer than those in the mechanical flotation machine. The general opinion is that the flotation column can show some effectiveness in specific cases as long as it is properly designed and carefully controlled.

Jan 1, 1988

By Dennis Ortega, Rich Kramer

After several operational improvements to FMC's Westvaco Mine Longwall, an ergonomic and operational bottleneck resulted at the mobile belt tail/rigid conveyor junction. Ergonomic hazards, cutting time losses, and spillage problems near the belt tail were identified and targeted for improvement. FMC Westvaco, consulting with FMC Material Handling Division, corrected the bottleneck using an expandable/retractable conveyor system to fill the gap between the mobile belt tail and the rigid conveyor structure. This paper explains the operational expectations, defined before; the challenges, encountered during; and the real outcomes, measured after the installation of an expandable/retractable conveyor system.

Jan 1, 2002

By A. M. Laird

Endako Mines' molybdenum operation is located near the geographic center of the province of British Columbia, Canada. The property is six miles south of the Northern Transprovincial Highway and the northern main line of the Canadian National Railway. The area is broken by high hills covered with dense stands of spruce and pine with vast areas of the valley floors covered with aspen and poplar. The climate is moderate with precipitation averaging 22 inches per year. Approximately four feet of snow accumulates in the winter, and temperatures range from 900 F. in summer to -40° F. in winter. The orebody, a lowgrade porphyry type deposit, occurs in a widespread granitic intrusive which has been locally weakened at the intersection of two regional faults. In this vicinity the quartz monzonite has been further shattered to permit the entry of mineralizing solutions and local dykes. Two types of mineralization occur within the orebody. The most prom¬inent is the six inch to four foot wide continuous quartz veins with characteristic ribbons of molybdenite and frequently finely-divided grains of molybdenite within the quartz. The second type occurs as fine fractures filled with quartz molybdenite in the form of a stockwork halo radiating out from 20 to 200 feet from the quartz veins. Minor hematite, magnetite and chalcopyrite are also present. Mineralization is roughly proportional to the extent of kaolinization in the quartz monzonite, kaolinization being one of three distinct forms of hydrothermal alteration. Pyrite is commonly associated with molybdenum mineralization within the orebody and a pyrite halo is recognized on the south side of the orebody.

Jan 1, 1968

By M. J. Meulendyke

Within the mineral processing Industry. a range of grinding conditions exists which include semi-autogenous grinding (SAG), rod milling. and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1989

By D. L. Petersen, C. R. Nelson, P. M. Bergson, B. K. Nelson

Membrane waterproofing systems in large tunnels cause the partial decoupling of the concrete liner from the rockbolted and shotcreted reinforced rockmass. This decoupling leads to a loose fit of the liner in the excavation when shrinkage from cooling and moisture loss occurs. This increases tensile stresses which require either the addition of reinforcing steel in excess of common European practice or the potential for liner cracking. Hot weather concrete placement and cold weather service conditions increase the magnitude of the problem, while creep of the rockmass reduces it. Contact grouting also reduces, but does not eliminate, the problem.

Jan 1, 1991

By B. P. Atkin, D. W. Brown

A handleability monitor was designed to provide a simple, rapid, on-site assessment of the whole or part consignment of a coal blend in its "as-received" condition. The monitor was evaluated at a number of coalhandling plants, which handle both metallurgical and power station coals from a variety of sources worldwide. The results can be used to predict which coals could routinely pass through a handling plant at line capacity without causing blockage or delay. Despite extensive analysis of the data, it was not possible to correlate the handleability index to the regular sample analysis of moisture, ash and size analyses of the coal blends.

Jan 1, 2002

By S. Komar Kawatra, Henry J. Walqui, Timothy C. Eisele

Population balance models were used to model the grinding action of industrial scale coal pulverizers. Experimental work was conducted with two different coal samples to determine the values of the appearance and selection function. These functions were determined for vertical mills by using s 6-inch by 10-inch laboratory roll mill to represent the action of a vertical mill. Two very important operating variables were identified for vertical mills: feed rate and roll spacing. Factorially designed experiments were used to analyze .and quantify the effect of these two variables. The models were then adapted to represent changes in operating conditions by incorporating the effect of the feed rate and roll spacing effects. This resulted in a simulation model able to respond to changes in operating conditions, by providing corrected predicted values for the product size distribution.

Jan 1, 2002

By G. R. Brunskill

The molybdenite flotation plant at the Magma Copper Co. San Manuel concentrator has been in operation since 1956. In January of 1980, the plant was converted from a hydrogen peroxide-ferrocyanide process to the current sodium cyanide-sodium hydro- sulfide process. This paper is an operational review of Magma Copper Co.'s molybdenite recovery circuit, column cell flotation experience, and use of on-stream X-ray fluorescence analysis.

Jan 1, 1987

By Surendra K. Mishra

Recent land ban act has put pressure on industry to decontaminate the waste streams before they could be discharged. However, for both metal and organic contaminated wastes, there are commercial incentives to recover usable resources. Recent technology developments have helped meeting such objectives. This paper reviews developments in treatment technologies for industrial wastes. Major chemical groups used in waste treatment are summarized.

Jan 1, 1994

By Scott D. Kinsala, Patrick T. Flynn, Andrew T. Rosol

During calcination of diatomaceous earth, cristobalite is formed in varying percentages. Also, during efforts to recycle products containing natural diatomaceous earth, various heat treatments are used which may or may not result in the formation of cristobalite. The ILO (International Labor Organization) Encyclopaedia of Occupational Health and Safety states that conversion begins at 450'C and in the presence of a flux, is complete at 800'C. Due to the potential adverse health effects associated with crystalline silica, a more thorough understanding of the time/ temperature relationship is needed. Tests performed under controlled conditions do not substantiate the claims made in the ILO Encyclopaedia.

Jan 1, 1991

Successful longwall gate entry design requires control of vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses can also be highly destructive but they are less well understood. This paper discusses measurements of in situ horizontal stress fields in the eastern United States, experience with horizontal stress in longwall mines and methods for predicting and controlling horizontal stresses. The information presented was collected through site investigations at 45 US longwalls and an international literature review.

Jan 1, 1992

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By Thomas G. Johnston, Garston H. Blackwell

The development of a block model for a copper molybdenum ore deposit is described. The early use of the inverse distance power estimator, and later transition to geostatistics and kr iging, produced block models suitable for global reserve estimates. Because the global reserve was inadequate for routine mine planning, the production blast hole assays were incorporated into the block model, resulting in excellent local grade prediction. The on site use of small mini, and more powerful personal computers for estimating grades is described. The development of a computer aided, interactive graphic, mine planning system utilizing the grade block model is detailed.

Jan 1, 1987

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

The development of economical and effective treatment processes for solid and aqueous waste is a critical issue facing the mining industry today. Cyanide, nitrates and acid rock drainage are environmentally sensitive effluents that require treatment or containment for acceptable disposal. In situ biotreatment processes are an emerging technology (Thayer) for cyanide oxidation, denitrification, sulfide mineral alteration and metal re- mineralization. Biological cyanide oxidation is competitive with chemical treatment processes (peroxide, alkaline chlorination) for process solutions, spent ore and tailings detoxification. Microbial denitrification treats mine waste contaminated with nitrates from blasting, processing or nitrification of the host rock. Bio-alteration of sulfide minerals and metal re-mineralization may present the most cost-effective and environmentally acceptable method of dealing with sulfide tailings and leachate solutions. Field test programs for cyanide bio-degradation and denitrification of spent ore and process solutions were designed and run at two mines. Although the treatment bacteria and the application processes are similar, each waste presented site-specific problems for adapting the biotreatment processes. Some of the site problems include climate, ore geochemistxy, field bacteria production, waste microbiology and application engineering. This paper compares treatment design and results for cyanide oxidation and denitrification in heap detox treatments.

Jan 1, 1992

By A. C. Ruckman, Allen G. D., G. H. Beckwith

This paper describes the design and operational features of several asphaltic concrete gold heap leach pads which have been constructed in the United States over the past 12 years.

Jan 1, 1988

By J. Kulczycka

Poland in time of transition had been dealing with the remnants of the previous regime ? particularly in the field of environmental protection. The burden left was tremendous and there was a need for fast and effective tools for improving the environment. The idea of environmental protection had been supported by the introduction of a new environmental policy that underlined the importance of sustainable development in industry in the beginning of 1990s. This policy introduced high environmental fees and fines ? a concept not very popular in Europe in that time ? and good only for a country in transition to boost the protection of the environment. While this policy had its role to play, its role is now completed. It is time to move forward, especially when these environmental charges affect the international competitiveness of industries so much, and at the same time have virtually no influence on environmental protection investments any more.

Jan 1, 2005