Search Documents

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

By Mario E. Rossi

The concept of entropy is classical in thermodynamics and information theory. Its potential use as a measure of the ordering of a spatial system is discussed. Although entropy has been discussed previously in the framework of spatial statistics and for univariate distributions, a bivariate data-based estimator has not until now been defined. Different statistical distributions maximize entropy, depending on the univariate, bivariate, or n-variate constraints applied. For bivariate distributions, with a known mean and known covariance, it can be shown that the distribution that maximizes the entropy of the system is the bivariate gaussian. A nonparametric bivariate entropy estimator is introduced, derived directly from the experimental cumulative frequency distribution. Assuming that this experimental bivariate distribution is representative of the population distribution, then a measure of departure from gaussianity can be introduced as a relative entropy estimator. Practical applications for the entropy estimator are discussed, and an example developed.

Jan 1, 1992

By Prisbrey K., N. Choi, A. Burbank

Large tonnages of low grade refractory gold ores are not presently being treated because they resist direct cyanide heap leaching and because they are too low in grade for more expensive oxidizing pre-treatments. If they could be oxidized while remaining in heaps, they could be economically leached with cyanide. The solution is to use bacteria to partially oxidize the encapsulating pyrite mineral which allows cyanide dissolution of the gold in a separate treatment. A variety of refractory ores from different locations was crushed to minus three quarters inch, loaded into columns, and inoculated with T. ferrooxidans. The bacteria attacked the pyrite causing biooxidation, and gold recovery increased 30 to 120 percent after three months curing.

Jan 1, 1990

By P. Pal Roy, Ajit Raj Ostwal, M. M. Singh

Field investigations have revealed that sawdust can be used as an efficient additive to ANFO for carrying out production blasts in limestone mines. Sawdust can be used at a reasonably reduced cost without sacrificing fragmentation, muck profile and wall control. Such additives lower the detonation pressure of ANFO by acting as low-grade fuel that reacts or burns more slowly in the presence of ammonium nitrate than does fuel oil. On detonation, it eventually forms near-ideal oxygen balance that helps in liberating maximum energy to break the surrounding rock. It also forms a low-density stable mixture that helps in reducing loading density (kg/m) of explosive in the blasthole. Experiments performed at the Hirmi Limestone mine, M/s L&T, and at the Lambasta Limestone mine, M/s Jaypee Rewa Cements, showed the novel acceptance of the technique in a highly competitive market where cost reduction has been a major area of thrust.

Jan 1, 2003

By Stanislaw Wasolewski

Computerized systems for ventilation parameters monitoring which are used in Polish coal mines provide the ventilation staff with a great number of measuring data. These data can be used to get knowledge about dynamic properties of ventilation process and disturbances affecting its state. This is necessary to create a reasonable concept of mine ventilation control system and make a practical application of such system. In the paper a method of ventilation process identification with the use of measuring data from monitoring system is described. Computer analysis of time series including statistical, correlation and frequency methods are applied to estimate dynamic properties of ventilation process and its disturbances. Using the Fast Fourier Transformation (FFT) algorithm the parameters of the process have been obtained which can be efectively used in a system for mine ventilation control.

Jan 1, 1991

By Gun Berglund, Eric Forssberg

Sulphide mineral flotation is known to be affected by oxidation-reduction conditions in the pulp, although there is some doubt as to whether it is the oxidizing environment or the type of oxidant which influences flotation. Variations in the oxidizing conditions of the pulp and their subsequent effect on flotation were examined for two types of natural sulphide ore, a galenasphalerite ore and a complex pyrite ore. Different gas mixtures ranging from pure nitrogen to pure oxygen were used to control the oxidizing conditions. Zinc recovery increased with a more oxidizing environment, and nitrogen gas acted almost as a depressant for sphalerite in the flotation of the Pb-Zn ore. For the complex pyrite ore, the selectivity between chalcopyrite and both gangue and pyrite improved when the environment was oxidizing, resulting in higher Cu recovery in the copper rougher concentrate. The use of an oxygen rich flotation gas was found to be a suitable method for changing the oxidizing conditions and improving flotation under controlled conditions. The flotation results were correlated to the oxygen content and the redox potential, parameters which describe the pulp chemistry conditions.

Jan 1, 1989

By John M. Anderson

This paper examines the methods available to improve climatic conditions around a deep, high production longwall district of a British coal mine using results from a computer model. Such methods include the provision of increased ventilation quantities, the application of refrigeration, the reduction of heat input at source and the use of alternative ventilation systems. An approach to the solution of a climatic problem is explained with reference to other coal mine contaminants and a cooling strategy for deep high production British coal mines is described.

Jan 1, 1987

By H. H. Murray

New and improved beneficiation techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques include particle size separation, high intensity magnetic separation, chemical leaching ,flotation, and selective flocculation. The blending of clay minerals with other minerals provides opportunities to make special ceramic materials such as cordierite and other minerals that have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1990

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

"In the mining industry, high-level commitments to adopt sustainability have been made at the corporate levels of mining companies, but there continue to be problems when attempts are made to adopt these high-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into day-to-day minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies. A proposed methodology to achieve integration of sustainability at the operational level will direct the systematic and rigorous identification and characterisation of sustainability issues in an operation. The methodology allows different approach strategies for assessment, comprehensive accounting of sustainability indicators and has the ability to identify sustainability issues which may have significant business implications that cannot be identified using traditional analysis processes."

Jan 1, 2011

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By Ed Van Eeckhout

The rockburst monitoring system at the Sunshine Mine has recently been improved to increase the certainty of burst locations and to output location results in a manner amenable to easy interpretation. Three methods of location calculation were used: a computer code provided with the hardware in-place (the MP-2501, a code based on the least-squares method (Blake et a1, 19741, and a nonlinear iterative code written by the principal author. The more accurate locations are given by the latter two codes, but still are only correct to within about 100 ft. This error is due to uncertainties introduced by the geologic and mining variations versus the assumptions made in the location codes. Software was then written to make two-dimensional plots of burst location by level, so management could monitor problems easily.

Jan 1, 1986

By J. B. Rubinstein, V. J. Badenicov, S. T. Hall

A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calcetest results is developed (scaling-up), and applied for calculating the design of commercial-scale columns.

Jan 1, 1996

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By Joseph Corvetti

This paper is of conceptual nature. The authors present their idea of creating an integrated and intelligent excavation design system. Research work has just been started and the results will be addressed during presentation of this paper. The authors are currently engaged in a pilot study and expect to build a feasibility prototype expert system (establishing the numerical-cognitive coupling in excavation design) by the end of this year.

Jan 1, 1996

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By Svante Lundbrink

A new generation hydraulic rock drill featuring more than 50 percent higher performance than other drills has been introduced by Atlas Copco. In conjunction with the new rock drill, control systems have developed and refined to handle the higher drilling output, and to maintain an acceptable service life of drill string components. These improved features are built into the Rocket Boomer, a new high-performance drill rig, used at the recently completed Hanging Lake project in Colorado. Experiences from this project will be reported together with results from a highway tunnel construction project in Italy.

Jan 1, 1991

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using discrete system simulation. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution used in a random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing needed and provides verification of how representative the samples are.

Jan 1, 2002