Search Documents

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By Yuusaku Tominaga

A flexible expert system for a personal computer has been developed to take countermeasures for prevention of emergency in underground coal mines. The system makes a diagram to estimate maximum airflow rate of a specified branch such as coal face or advancing face, etc. under the conditions of opening regulators set in any two different branches, by computer simulation. The system approximates the ventilating condition underground by using both measured values and safety factor derived from the rules in the system. The probability of happening gas explosion, spontaneous combustion and mine fire underground is shown on a display and countermeasures in a data base in the system are selected according to a confidence factor. When it is recognized in the system that either safety factor or confidence factor of countermeasure has a small value, the system sends information relating to reasoning in the system to registered human experts by computer communi¬cation and facsimile. The replies in file transfer from the experts are stored in the system and reconsultations for estimation of underground condition are started automatically. As the replies in facsimile are shown on the display, user inputs new rules and, values for reconsultation. It is shown that the system is available to take better countermeasures as the condition' of a network in coal mine is changed by mining day by day.

Jan 1, 1992

By Jim Wilcox

Introduction In 1979, rumors of a developing drug problem within IMC Fertilizer's Carlsbad, NM workforce began to surface. For the next two years, a management team contacted local, state, and federal regulatory agencies that had the potential resources to help combat this apparently escalating problem. These contacts included the local police department, the county sheriff's office, the federal Drug Enforcement Administration, and the Mine Safety and Health Administration (MSHA). IMC approached each agency with two proposals. The first required the agency provide an undercover agent for placement in the company's underground facilities. The alternative required the company to provide the agent with the participating agency lending necessary legal expertise and guidance to accumulate the necessary data. MSHA regulations prohibit intoxicating beverages and narcotics on mining property. They also forbid persons under the influence of alcohol or narcotics from working in or around mines. The agency could not, however, help with this problem. The remaining agencies were sympathetic, but were unwilling to assist in implementing either program, citing legal implications. Without exception, these agencies not only refused to provide help, they discouraged any type of undercover operation, searches, drug screenings, or using dogs trained in narcotics detection. As law enforcement officials, they reasoned that any such program constitutes potential civil rights violations. An attorney advised IMC that it was not required to adhere to the same guidelines as law enforcement and regulatory agencies. It was his legal opinion that the company could conduct an undercover operation. But he recommended finding a private firm that specialized in this type of investigation. An experienced firm should have the expertise to conduct the operation and avoid the legal pitfalls that could be encountered. The management team agreed with the attorney and elected to hire a private firm. After extensive research and evaluation, three reputable companies were contacted, advised of the needs, and asked to submit a proposal. Their initial response was enthusiastic. None, however, submitted a proposal. Each was unable to locate a qualified agent willing to work in an underground environment. Privacy and civil rights At this point, it was apparent that an undercover operation was not feasible due to the lack of inhouse expertise and the lack of outside assistance. After more research, it was concluded that the only viable options left were the ones that the law enforcement community had earlier discouraged. These options included locker and personal searches, use of dogs trained in narcotics detection, and drug screening or testing. The management team evaluated the pros and cons of locker and personal searches. They concluded that if conducted properly, this approach could eliminate the problems. The potential legal liabilities, however, appeared to be tremendous. Strict guidelines would have to be adhered to in order to avoid invasion of privacy and civil rights violations. This meant announcing locker searches before conducting them and obtaining written permission from an individual before searching his person. Although the group was reluctant to lose yet another option, it was concluded that conducting searches under these conditions would be ineffective. It would also convey the message to the workforce that the substance abusers had the upper hand. This author was extremely critical of this legal opinion at the time. I have since concluded that the attorney was correct. This occurred in mid-1982. Court decisions of that era indicated the legal and political climate was sensitive to these issues. These activities would probably have been prohibited even if they were

Jan 11, 1987

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery Recent developments in electrooptic inspection of dry and wet material leaving a grinding device are critically reviewed New methods for characterizing ultrafines are discussed A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine Index and other fineness indices is described

Jan 1, 1983

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By J. L. González-Chávez, A. Ballester, M. L. Blázquez, F. González

In recent years, the bioleaching of sulfidic raw materials has been of great interest. However, the application of this biotechnology is now very limited for many different complex reasons. The mechanism of the chemical and electrochemical reactions taking part in the process is not well understood. The application of electrochemical techniques is useful in its elucidation. Among the common sulfides, galena has been studied very little with respect to its behavior during bioleaching. Therefore, the electrochemical evolution of massive electrodes of lead sulfide in the presence and absence of' a mixed culture of mesophilic microorganisms was investi¬gated by the application of potentiometry, anodic and ca¬thodic polarization and cyclic voltammetry. The agitation rate, the use of pH control and the composition of the nutrient mediums did not have any significant affects on the oxidation of galena. However, the temperature (25 'to 45 °C), the scan rate (4 to 100 mV/s) and the acid used to adjust the pH were significant variables that influenced sulfide oxidation. There¬fore, the peak (600 to 1,000 mV) corresponding to the oxida¬tion of sulfide ions from the mineral was only detected in the presence of a complexing anion of lead. In the presence of bacteria, the peaks corresponding to galena oxidation de¬creased and, at the same time, new peaks appeared both during the oxidation at -300 mV and during the reduction of the mineral surface at 150 and -300 mV. These signals were more important when the attack time increased. The rest potential of bioleached mineral increased with an increase in leaching time, which was related to the electrochemical transformation of the galena surface.

Jan 1, 2000

By R. P. Killmeyer, R. E. Hucko, P. S. Jacobsen

Cleaning of three coals from the eastern US was tested by five selective agglomeration processes and one selective flocculation process. The coals and processes are described, and the results are reported and compared. Two of the processes, which ground the coal to the finest volume mean diameter, met the stringent test program quality specifications.

Jan 1, 1991

By L. Alan Weakly

Page one is missing from book

Jan 1, 1982

By Alfred A. Roetzer

In several sections of the country new demands are being brought bar cement users. Among these the demand' for truck shipments; and palletized loads present new problems that do not lend themselves to sample solution. In fact these demands have far-reaching effect in the way bagged cement might be marketed. Early solutions of palletized truck loads filled from existing packing and loading facilities have resulted in' slowdown in packing, additional labor and space for palletizing, considerable experimentation in type and construction of pallets, and usually far from optimum truck handling and loading methods.

Jan 1, 1961

By Michael D. Zuber

This paper discusses the use of a coalbed methane simulator that has been modified to account for the removal of grid blocks as a function of time to estimate gas emission and production for a variety of mine-associated problems. The specialized features of the simulator are presented. Example applications illustrate the models' use in estimating methane emission rates during mine roadway development, and estimation of longwall panel degasification by horizontal boreholes.

Jan 1, 1997

By Arol, A. I., I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of rnontmorillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: a chemical method using such complexing agents as EDTA and sodium tripoly- phosphate, and a mechanical method involving ultra- sonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1988

By C. Maltesh, P. Somasundaran

The ever increasing need for treating fine complex mineral bodies has led to the evolution and rapid development of advanced processing techniques for fine grinding, classification an if mineral separation and purification. With the introduction of these new technologies and understanding of underlying fundamental principles, mineral processing is now being applied to materials ranging from ceramics and composites to superconductors. In this review, current and potential applications of mineral engineering techniques to advanced materials processing are discussed. Particularly, material processing involving ultrafine grinding, dispersion and flocculation and thin film formation is examined. Novel techniques of solid/liquid separation involving manipulation of interfaces and use of high intensity high gradient superconductor magnetic equipment for solid/solid separation are discussed.

Jan 1, 1990

By B. K. Baird, P. C. Satchwell

The application of cutoffs during and after pit optimization is examined for a lower-grade multimetallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block. The calculation incorporates parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which parameters have significant effects on the total contained resource tonnage and total contained nondiscounted revenue in the optimized pit. The cumulative effects of changing several of the more-significant parameters are investigated The application of a copper cutoff grade to a block inside the optimized pit could result in the less-than-optimal extraction of the resource. A block with a copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher-copper-grade block may be subeconomic. Also discussed are the merits of applying a copper-grade cutoff, an "equivalent-grade" cutoff and a dollar-per-ton cutoff to blocks inside the optimum nit.

Jan 1, 2002

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By R. E. Muller, L. G. Martin, J. M. Stonehouse

Erratic distribution of values in free gold ore bodies presents severe problems in sorting material in large scale open pit mining. However, an intense program of modern blasting techniques and less than modern gold panning results in good sorting at Houston International's Manhattan mine. Blasting technique is important. If the sample location cannot be relocated because of blasted material movement, information acquired while drilling is useless. So short benches are critical to minimize dilution. Though not very accurate, panning allows for rapid analysis. The more accurate fire assay does not provide the needed speed. Panning can be fairly accurate and errors made are mostly on the low side. Samples of mixed and broken stockpile material are used as checks on pit procedure and to develop stockpile content in¬formation. Added tonnages discovered offset the higher labor costs of this careful sorting technique. The mine is located in central Nevada's Toquima Range in the small mining town of Manhattan, 322 km north of Las Vegas. The mine has four epithermal stockwork ore bodies that are mined in two pits. The mine problem was that conventional ore control was not separating ore from waste. Assays of 6-m blast-holes were used on 5-m centers. The blastholes were relocated by stadia survey after blasting. Holes assaying above the cutoff grade were flagged and mined as ore. This system is practical and useful in high concentration ore bodies or in evenly disseminated mineralization. But it was not practical at Manhattan because of large gold particles and small ore pocket sizes. Ore pockets were often missed when drilling a grid area for blasting. Also, large gold nuggets made assay results unreliable. The probability of a nugget being contained in an assay charge is small. So most results were low, compared to actual grades mined based on stockpile samples. When a nugget found its way into a fire assay charge, the result would be far higher than the actual grade of material represented. In addition, disturbance by blasting created problems in relocating ore. Because of these problems, the grade control program was intensified in September 1979. It successfully separated ore and waste in blocked out ore areas and located more ore in "waste" areas. Known reserves mined to date have increased up to 50% on some benches. The methods used are modern blasting techniques, detailed assaying, and traditional panning of samples collected from active mining faces. These methods allow mining flexibility, to match the variable mineral occurrence in ore bodies. The united effort of the geology and engineering departments has been important to the program's success.

Jan 12, 1980

By D. Kump

Barrick closed the Bullfrog Operation in November 1999.During its life, the Bullfrog produced ore from three open pit mines and an underground mine; 32,000,000 tons of ore were processed at the 9,000-ton per day oxide mill. The mill tailings were deposited in a 320-acre tailings impoundment. When operations ceased, an estimated 750,000,000 gallons of water remained to be removed from the tailings impoundment. During operation, the drain down water from the tailings impoundment was pumped back to the mill for reuse; since closure of the mill, the drain down water has been managed by a combination of passive and forced evaporation.

Jan 1, 2004