Search Documents

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By Earl H. Miller

The United States Potash Company was the original discoverer and first producer of under-ground mined potash ore in North America and commenced active production of potash in 1931. In July 1956, the company merged with United States Borax & Chemical Corporation and is now a Division of that corporation. The mine is located twenty-two miles east of the city of Carlsbad and the refinery is located sixteen miles south of the mine, The mine was placed where the ore was found and the refinery placed where there was sufficient water for a dissolving and re-crystallization plant. For twenty-three of the last twenty-six years, the potash ore was mined with the room and pillar method, taking approximately sixty percent extraction and leaving forty percent in pillars. These pillars are generally fifty-eight feet by fifty-eight feet square. Three years ago, it was decided that removal of as large an extraction as possible from these pillars should be commenced.

Jan 1, 1958

By Lynn B. Hales, Randy A. Ynchausti, Robert W. Colby

Process control systems have evolved from single loop control to distributed control with computer based expert control strategies. The next step is to add adaptive control to the expert control strategies. An object-oriented intelligent adaptive optimization approach is defined and simulated results are presented.

Jan 1, 1995

By P. Massacci

This study deals with the development and utilization of computer models for evaluating the extent to which variability of raw material grades can be reduced from the deposit to the processing plant. The specific case of a cement works is examined. The deposit and the elementary quarring operations were modeled for the medium and long-term planning of production with the objective of predicting grade variability of the flow stream in time. The feeds inferred from previous modellings were used for simulating storage operations. In particular, the storage process (linear stockpile, as an alternative, blending from various heaps) was modelled in order to select the main parameters of the process to minimize grade variations of the feed to mill. The ways followed for modelling the prehomogenization process are described. The homogenization performance and efficiency in the silo stage has also been studied and an estimate made of the distribution of residence time on the basis of input and output sampling.

Jan 1, 1986

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By Y. T. Auck, M. E. Kukura, L. G. Stevens

At its Technical Development Center in Tucson, Arizona, the UOP Mineral Sciences Division operates a completely integrated pilot plant testing a proprietary process for the extraction of nickel from limonite/saprolite ores. The process is based on the reductive roast- ammonia leach procedure now employed in several plants around the world. The process improvements are such that nickel extractions well above that experienced in these processes are possible, particularly on the more garnieritic/saprolitic ores. This paper will describe the process and the results of process development studies. The data show that pilot plant results confirm those obtained on the smaller laboratory and bench scales of experimentation.

Jan 1, 1979

By Lynn B. Hales

Flotation performance varies widely as feed conditions change. Maintaining metallurgical targets has proven almost impossible without automatic control. Traditional control methods and procedures are inadequate. Using on-line x-ray analyzers, reagent control and accurate froth level control with flotation models and "Expert" computer control systems has improved metallurgical performance significantly. Examples of actual plant cases are described as well as the expert system methodology.

Jan 1, 1989

By T. Altman

Using theory of network planning together with graph theory, an algorithm is presented that creates canonical diagrams for mine ventilation networks (M VN). The data generated by the algorithm is used in the construction and plotting phases of a program that automatically plots the canonical diagrams, which can then be used for further studies of a given MVN.

Jan 1, 1988

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By J. R. B. Lima

The present work emphasizes the selection in the separation of the apatite/calcite by the direct anionic flotation versus the double flotation, with a reverse second stage of the Jacupiranga phosphate ore. The double flotation would allow the obtaining of two concentrated solutions: one of them mainly constituted by a calcium carbonate material (CaCO3) and the other one, phosphatic (apatite). The calcium carbonate concentrated solution is used for the production of cement. The presence of phosphatic material in the calcium solution is not desirable, phosphor being a harmful element to cement. On the other hand, smaller quantities of calcite in the phosphate concentrate would represent a substantial economy in the processes of production of phosphated fertilizers. These processes make use of sulfuric acid to the solubilization of the apatite and the presence of calcium material consumes acid. Also that, when carbonates are solubilized, unwanted products are formed resulting in losses in the process and diminishing the quality of the fertilizer produced. These characteristics are discussed in the paper and are compared to another Brazilian phosphate ore, the reverse route of which can be considered more adequate. The results are discussed according to recent discoveries, and special emphasis is given to the use of corn starch and its crucial role in promoting the selection in the direct flotation process.

Jan 1, 1993

By C. I. Wilmot, A. Sass, J. VanDeBeuken

Introduction This chapter addresses the need for operation manuals, presents an outline as a guide for writing the manual, discusses who should write the manual, suggests how it is implemented and gives tips to potential manual writers. Theory & Purpose of Operating Manuals The primary objective of the operating manual is to provide every operator the benefit of a uniform minimum level of training. This training is not only critical to the safety and efficiency of every employee, but also provides a basis for incorporating future operational improvements into standard and emergency procedures. The manual promotes safety through- out and additionally has a special section devoted to safety. The operator should be able to find information on chemical and physical hazards as well as be exposed to safety procedures for such items as motor lockouts and tank entries. The operating manual will usually reference a separate safety manual or incorporate parts of the safety manual. Safety is also promoted through standardized procedures for operation of equipment. Standardized operation is the second most important reason for the writing of manuals. If equipment is started, operated, and shut down in a consistent manner, then operational efficiency should be maximized. If it is not, then the procedure is adjusted until it is. The experience of many can be condensed into set responses for start up, shutdown, steady state operations, and upsets. Implicit with the standardized operation objective is a minimum level of training the operator will receive by thorough familiarization with the manual. The ability to know the contents of the manual is a basic requirement for operator status. The operating manual serves as a basis for a training program both at the start of the new plant and as new operators are hired or promoted into the job. The operating manual is a collection of at least part of the knowledge that "key people" own and will cushion the loss of key personnel for whatever reason. The manual can only fulfill these lofty goals by being a dynamic document. Manuals must change as equipment is modified and superior techniques evolve. To be effective they must be periodically updated, so word processors and reproduction

Jan 1, 1986

By Zhongxue Li, Wenguang Li, Yiqing Zhao, Shuaiqi Wang

"Faced with the serious managerial situations and diverse conditions and needs for mine safety, occupational health and environmental stewardship in Chinese mining communities, an evidence-based approach is proposed for the management of mine safety, health and environment integrity. By the proposed approach, tangible and effective scientific evidence should be collected and accumulated, and the authenticity, accuracy and applicability of the evidence should be assessed to form an evidence-based approach for characterizing mine safety, health and environmental hazards and risks from multidimensional perspectives. The results are then used to formulate diverse safety, health and environment functional requirements. In an evidence-based approach, the evidence is combined with the professional experiences and the actual economic and technological situations, availability and affordability of a mine. This approach is helpful to establish scientific, reasonable, acceptable and effective solutions for identifying and mitigating hazards and improving the level of mine safety, health and environment integrity of mining operations.Introduction / Background In recent years, economic reforms have opened China's economy so that Chinese society has rapidly modernized. Along with this advancement, the exploitation and utilization of mineral resources continues to be active and the scale of mining production continues to increase, which has created a deterioration in resource reserves and as well as the general condition of mining technology. There are many hazards and safety problems in mine production and occupational health as well as in the community environment in China’s mining industry. These problems threaten the security of China's mines and present serious obstacles and challenges to the industry and the government. According to the statistics from the State Administration of Work Safety Supervision, there were 50,500 mine safety incidents in China between 2001 and 2013, which consisted of 31,439 coal mine safety accidents and 19,061 non-coal mine safety accidents, resulting in 30 deaths (Qin 2014). At the same time, mineral dust and radioactive material from mine production processes have increased the morbidity rate of silicosis and cancer in mining workers."

Jan 1, 2017

By M. J. Klishis

This paper presents the findings of a study on roof bolter's hazard exposure. A "microanalysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries, and, from this, a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in root bolting operations. The research emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment-design problems that lead to human-error accidents.

Jan 1, 1996

By Michael Gauna, William J. Gray, Joseph C. Zelanko

Mechanized mining in the underground coal industry has continued to evolve since the introduction of the remote control mining machine. Remote control continuous mining machines without an onboard operator’s compartment are now the norm in the industry. Extended cuts in excess of 30 ft (9.1 m) are commonplace. Unfortunately, machine operator positioning has become an often unrecognized safety concern, particularly when remote control continuous mining machines excavate a turn (turn a crosscut). From January 2001 through July 2004, remote control continuous mining machine operators or helpers have been involved in ten roof fall fatalities and eight machinery crushing fatalities. The machinery crushing incidents occurred when machines were being repositioned or moved to another place. Of the ten roof fall fatalities, three occurred while a crosscut was being turned and a fourth fatality occurred while mining was being conducted adjacent to the crosscut. The operating time associated with turning crosscuts is a relatively small part of the mining cycle. In recent years, however, a disproportionate number of fatal incidents appear to have been associated with this activity. Procedures for reducing the incidence of operator fatalities while turning crosscuts are discussed. These techniques include: minimizing the number of turn cuts, limiting turn cut depth, establishing no work zones and using visual warning devices to designate them, installing more roof/rib support in the vicinity of the turn cut, using notch cuts prior to initiating a full turn cut, and positioning the remote control miner operator in nontraditional locations.

Jan 1, 2005

By Gordon R. Wicker, John A. Cole

Although the evaluation of autoclave oxidation for Getchell ore was begun nearly 40 years ago, its ultimate implementation in 1989 represents the first substantial improvement in the economics of processing this refractory ore. Sulfide ores at Getchell were previously roasted prior to leaching (in the 30's and 60's), resulting in somewhat lower recoveries than are currently realized by autoclave oxidation. Recoveries on the order of 90% are expected from the high-arsenic sulfide ore over the expected 10-year mine life.

Jan 1, 1990

By M. E. Rossi, V. Camacho

Reconciliation of production information is critical to evaluating the effectiveness of predictive models that would allow for the optimization of mining operations. Whether mining open pit or underground, mine-to-mill reconciliations can be one of management's better tools for the performance of proper accounting. Such reconciliations can also be a very useful tool in evaluation and optimization. This paper proposes a set of criteria and objectives for a typical reconciliation program. This paper also presents a stepwise, logical approach to performing reconciliations and discusses the benefits associated maintaining good information. It also highlights some of the potential pitfalls involved and the methods used to avoid collecting misleading information. These issues are illustrated with an example of a model-to-mine-to-mill reconciliation program that is being implemented at an operating mine. The program involves multiple predictive models (long-term and short-term block models), feed from three open pits and one underground mine, in addition to intermediate stockpiling, for a total of 23 mill streams. This paper presents a summarized version of this reconciliation program and its initial results as implemented at Minera Michilla S.A.

Jan 1, 2000

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By Hal McVey

There are thousands of industrial minerals occurrences in the world. The existence or nonexistence of a market for the minerals from these deposits dictates whether or not they will be developed. Therefore, a market srudy is an integral part of the evaluation and development of an industrial minerals property. Some of the factors to be considered in a valid market study are: Supply & Demand; Transportation; Specifications; Competition; Substitutes E Alternatives; Price and Market Structure. Of these, Transportation and Specifications are of particular importance to market evaluations in the field of industrial minerals. The market researcher, working closely with technical personnel in geology, mining and processing, can determine the technical and economic acceptability of the product to be produced from the prospective property and can often create areas of opportunity for marketing of industrial minerals.

Jan 1, 1980

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985