Search Documents

By Abdellah Chlk, Driss Msatef

Sedimentary phosphate ores are known for their relatively high specific surface area and porosity, which have a positive influence on their reactivity when used as fertilizer in acidic soils or in the manufacture of wet phosphoric acid and phosphatic fertilizers. However, these physical properties could have a negative effect on the behavior of these ores if dried. This effect has been studied on several phosphate ores samples by: the determination of mineralogical and textural properties of these samples, the determination of vapor water sorption isotherms, at different temperatures, from which the sorption heat has been calculated, carrying out several drying tests using a laboratory fluidized bed reactor under constant conditions, which showed important differences in drying rates and residual moistures.

Jan 1, 1999

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By P. J. Kientzler, Y. C. Lo

The current study is concerned with the analysis and attempt at simulating the product size distributions obtained from a vibrating ultrasonic device. Systematic experiments of comminution were performed with natural sizes as well as monosizes in order to understand the breakage behavior of the device. A precise analysis of the device's breakage performance in the case of fine grinding of alumina samples will be presented. Initial steps to model the breakage events using a detailed mathematical algorithm will be discussed.

Jan 1, 1992

By J. S. Walker

Public Law 95-87 enacted by Congress in 1977 and subsequent regulations require coal mine operators to predict the effects of mining on the environment prior to the start of mining. Prediction of the effects of mining on the local groundwater system is a difficult task due to its complex nature and the lack of detailed published information. An investigation of water level fluctuations in five we1 1s positioned over three consecutively mined longwall panels was initiated in conjunction with an intensive subsidence monitoring program. The purpose of this work was to provide detailed information which could be used to predict certain hydrologic effects of longwall mining in the Northern Appalachian Coal Region. The results of this case study indicate that water level fluct- uations in the local ground-water system above longwall panels is associated with subsidence and that the static water level will generally re- establish at or near the pre-mining elevation after mining is completed.

Jan 1, 1986

By John E. Urosek, Herman Schade

In March, 1988, a fire occurred in a large underground coal mine. Coal Mine Safety and Health of the Mine Safety and Health Administration was immediately notified of the situation. They requested the assistance of the Pittsburgh Health Technology Center (PHTC) to provide monitoring and analysis of the mine atmosphere in and around the fire area to insure the safety of the miners escaping from the mine and for the miners involved in extinguishing the fire. The capability to provide this type assistance is maintained by the PHTC Offices located at 4800 Forbes Avenue, Pittsburgh, Pennsylvania. The equipment used is maintained field ready and can be mobilized almost immediately. This paper will discuss the response to this recent major mine fire.

Jan 1, 1989

By Xinyang Xu, Jirun Xu, Changlie Deng, Kang Yan, Luo Qian

Cake filtration is a complex process and the cake constructure is very difficult to describe in theory. Cake constructure parameters, such as the cake prosity, pore size shape and even its distribution, are main factors influencing the filtration results but have not been thoroughly understood yet. In this paper the fractal theory, an effective mathematical method in describing the self-similar phenomenon is used to investigate the filter cake constructure, and the scanning electron microscope and automatic image analyzer are used to measure the cake constructure. Cakes which formed in different condition are examined and the fractal dimension of the cake are calculated. The study shows that the constructure of the filter cake can be approximated by Sierpinski fractal geometry and that the fractal dimension of filter cake, related to the particle characteristics, slurry concentration and filtration pressure is a good parameter to describe the pore size distribution and the cake penetrability.

Jan 1, 1995

By Nes?e Çelebi

It has never been easy to finance within mining sector. Leasing may be an alternative source of finance for mining investments. Leasing is acquiring the right of usage for an asset for a definite period of time without having the ownership of it. In this study, a model for analyzing the lease financing opportunities for mining investments under risk and suitable for establishing a satisfactory leasing policy for both lessee and lessor is developed. Using the model, it is possible to obtain an expected equilibrium lease amount acceptable by both lessor and lessee and also the expected range of the equilibrium lease amount as a decision tool. First the existing leasing policies are mentioned, then the developed model is described. A case study is presented to illustrate the use of the model in establishing a leasing policy. In conclusion, the usefulness of the model is discussed.

Jan 1, 1992

Political events during the past decade have caused businesses throughout the world to think globally. Countries once closed to free market enterprises are now open and seeking out foreign investment to help improve the well being of their populations. The mining industry has always been a global one. Today, though, the industry has become even more global. The driving forces behind this include the opening up of higher grade, lower cost mineral deposits in undeveloped and developing nations. In addition, permitting delays in the United States, coupled with stricter environmental guidelines and a general anti-mining attitude, have forced the mining industry to look outside US borders. The Mineral Economics and Management Society (MEMS) took as the theme of its seventh annual professional program "Economic Globalization of the Mining Industry." About 100 people attended the conference held in Arlington, VA in late March. Speakers included members of the investment community, academia, government and the mining industry.

Jan 1, 1998

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By D. L. Passmore, J. D. Bennett

The reliability of mine operators' reports to the Health and Safety Analysis Center of the US Department of Labor of days lost from work by injured miners is 0.267.

Jan 1, 1987

By W. A. Niepelt, F. A. Locher

Flow in steep cascades may lead to the occurrence of a nearly periodic train of waves known as slug flow. This, in turn, may result in overtopping of the channel walls and problems with energy dissipation in receiving sumps. Experimental data from an operating facility was used to extend clear water technology for predicting the occurrence of slug flow to conditions with slurry flows. A design methodology and a design chart to determine the region of steady flows is presented that will permit the design engineer to avoid slug flow in cascade systems for conveyance of slurries.

Jan 1, 1990

By R. Llerena, P. Dunstan, R. L. Amelunxen

A single four feet diameter cell, treating a Cu/Mo rougher concentrate, has been fully instrumented and linked to a Distributed Control System. This has enabled the writers to further understand the mechanics of operation of the cell, particularly that of the "TRANSITION ZONE". This is the volume between the feed port and the pulp-froth inter- face. The results have shown a need for the re-designing the control loops whereby the Transition Zone volume (or pulp level ) becomes the single most important control parameter to achieve the de- sired recovery. Air consumption, previously thought to have played this role, is now kept at precoalescence level s for maximum efficiency.

Jan 1, 1988

By Sii Smith-Gruner

Blasthole drilling by todays standards is not a mature operation. In most mining appli¬cations, the blasthole drill rig is the least understood piece of machinery. Draglines, mining shovels, and haulage trucks may have more charisma, but the entire mining process starts with the drilling of blastholes to facilitate removal of the overburden and/or the primary material being mined. There are two (2) principal drilling methods them being rotary and percussion. In certain situations, percussion drilling is the most practical method, but for most applications, rotary drilling using the rotary tricone bit is the common and accepted drilling technique. While the drilling rig is on the surface and quite visible to everyone, it is really the object at the end of the drill pipe, the tricone bit, that is doing the work and drilling the hole. The rig supplies power to the bit and air to clean the hole. In addition, it must be capable of providing certain other functions and should be properly outfitted to adequately support the rotary tricone bit.

Jan 1, 1988

By Neville T. Moxen, Stuart K. Nicol, Malcolm D. Engel

Ion flotation is a process in which ions of interest are complexed with a suitable surfactant molecule. A dilute solution containing these complexes is then aerated, under which circumstance the surface-active complex concentrates at the air-water interface and is transferred to a froth. The present work describes some of the phenomenology of this process and experimental work leading up to the design and use of a pilot scale laboratory facility. Early experiments suggest that selective recovery of gold can be obtained in a manner at least equivalent to conventional CIP processing at low capital cost. Under favourable conditions, upgrade ratios of gold ions of the order of 180: l have been achieved from reclaimed residue dam water with as low an initial gold level as 0.2ppm. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal processing.

Jan 1, 1990

By Gary Johnson, Bill Mackenzie

The Paddy's Flat plant of Dominion Mining Limited was commissioned in March 1988 with a design throughput rate of 700,000 tpa. The plant now treats ore at an annualised rate of over 2,000,000 tpa. The only major capital improvement to the plant has been the addition of a pebble crushing circuit. Whilst significant changes in the average hardness of the ore being fed to the plant have obviously occurred, a number of processing innovations have been necessary to enable these throughputs to be maintained. The treatment of ore types with a wide variety of physical properties has been a feature of the operation of the Paddy's Flat plant. The leaching characteristics of the ores are relatively straight forward, and it has been possible to considerably enhance the rate of gold extraction from the ore. Reserves of soft surface ore have been increased which has created the opportunity to improve the profitability of the operation by increasing throughput to considerably above the design level, without having to increase the capital investment in the plant.

Jan 1, 1992

By Frederick W. DeVries

The following charts were presented at the Randol Gold & Silver Forum 2000, held at the Hotel Vancouver (Vancouver, B.C.) from April 18-21, 2000. It must be borne in mind that the "facts" stated and con­clusions drawn by the author were not as the result of a rig­orous technical investigation, but rather as a member of a journalistic team seeking a rapid view for presentation as news to a TV audience. Since the author's visit, some retrenchment on the part of the operators on estimating the cyanide content of the spill seems to have occurred. This does NOT alter the conclusions that (a) the spill was an intolerable embarrassment for the world mining industry, nor (b) the potential damage to future mining investments, should prompt action not be taken: 1. to understand the reasons for the dam failure, and 2. to draw up firm concepts of how to avoid future fail­ures of dams at mining properties containing materials that are toxic, environmentally unfriendly, or with as highly dis­comfiting a profile as cyanide.

Jan 1, 2000

By W. D. Gould, . W. Koren, P. Bedard, P .. B. Marchant

Ammonia and nitrate in metallurgical operations arise from several sources: (1) the use of ammonium nitrate based explosives, e.g. ANFO; (2) the use of cyanide for gold extraction which is degraded to ammonia by most cyanide destruction techniques; and (3) the use of nitrogenous reagents in the mill for neutralisation, flotation and extraction. The concentrations of ammonia and nitrate in effluents vary from 10-50 ppm and 25-300 ppm respectjvely. A number of environmental problems are associated with both ammonia and nitrate. Both of these forms of nitrogen can contribute to the eutrophication of receiving waters. Ammonia and organic nitrogen can also cause high dissolved oxygen demands in receiving waters. Ammonia is also toxic to fish, particularly at elevated pH values. Several methods are in use for the removal of ammonia and nitrate from municipal wastewater, industrial effluents and agricultural runoff. To date, no treatment systems have been developed specifically for the removal of nitrogen from mine and mill effluents. This paper will report on some removal techniques that have been tested using actual and synthetic mine effluents.

Jan 1, 1993