Search Documents

The importance of factoring mining dilution into the estimation of ore reserves in an open pit mine is discussed. An example that relates the issue of mining dilution to the size of the smallest volumes that can be mined selectively is given. The relationship between the size of the selective mining units (SMUs) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate a variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1998

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By S. Chander, A. Briceno

The effect of sample storage in argon and in air on the kinetics of oxidation of pyrite from a coal source was studied using accelerated-weathering tests that were performed in laboratory columns. Prior to the weathering tests, the samples were crushed, ground and stored for various periods of time in either argon or air. The test results showed a dramatic difference in the rate of oxidation of the aged samples. The interpretation of the differences was based on the hypothesis that the aging of pyrite led to the formation of surface coatings that changed with time. "Dry" oxidation produced surface coatings that had properties different from those produced by "wet" oxidation. The significance of these results to pyrite/reagent interactions during flotation and in evaluating the acid-mine-drainage potential of pyritic waste materials is discussed.

Jan 1, 1995

By Bruce D. Hansen

The complexity of large geographically diverse or multicommodity mining companies requires a corporate structure, which provides the maximum long-term effectiveness. Structure models exist along the spectrum of centralization to decentralization. This paper examines the trade-offs of flexibility, cost, decision making, consistent strategies, and corporate control associated with different structural models as applied to mining companies. The mining industry typically lends itself to a business unit model. However, the degree of decentralization depends on size, proximal operations, technical complexity, product mix, geographic spread, mining methods employed, and the inherent capabilities of an organization.

Jan 1, 2001

By Deepak Malhotra

The economic viability of mineral companies not only depends on maximizing mineral recoveries but also on their ability to do so at minimum cost. Increasing pressure to cut costs has resulted In reduced staff, thereby decreasing the capabilities of routine metallurgical audits. This paper reviews a systematic approach to plant auditing which has been used successfully at several operations. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1991

By S. Orr

Flow in heaps and dumps is a two-phase flow phenomenon, though for many applications it could be simplified as unsaturated flow. Unlike saturated flow (typical of ground water flow), where permeability is independent of other hydraulic parameters, unsaturated flow permeability depends on the degree of saturation and/or on capillary pressure. Several recent field studies suggest that flows in heaps and dumps tend to concentrate in preferred pathways, bypassing much of the ore. Different preferential flow phenomena are triggered, promoted and influenced by different heap structures, by pretreatment, by the composition of the leach solution and by application rates and schedules. The structure of heaps and dumps is determined and affected by every stage of their construction -from blasting to crushing to conveying and stacking of the material. History of heap construction and operation combined with monitoring, mapping and certain field tests can reveal patterns of flow and transport in a given heap and can shed light on the physical mechanisms behind it. Such insight can provide a first cut on heap leaching enhancement by either eliminating or bypassing physical barriers to flow and leaching. Based on the understanding of the heap structure, advanced flow and transport models can be constructed and further enhance the insight. This insight is essential for understanding cause and effect and can provide a basis for decision making. Further, based on the physically-based models, an intelligent control agent, such as MRDS1, can learn and build a self-learning representation (or a model) of the complex heap leaching system, followed by dynamic optimization and planning of heap leaching and heap rinsing.

Jan 1, 2003

By L. A. Hansen, D. L. Buffington, G. H. Beckwith

This paper reviews geotechnical engineering considerations in heap leach pad design, discusses design philosophy and provides design procedures. A brief discussion of surface water hydrology ground- water protection and other design considerations are also presented. Special emphasis is placed on projects in the arid and semiarid regions of the Western United States where annual evaporation exceeds rainfall, and where good foundation conditions are usually present.

Jan 1, 1987

By J. S. Stachulak

Inco Limited operates nine underground mines on the rim of the Sudbury Basin. These operations are situated near the City of Sudbury, 589 km (365 miles) west of Montreal, and 363 km (225 miles) north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite, and pyrrhotite. Total ore production from underground is in excess of 51,000 tons per day. The total volume of fresh air supplied to the nine mines is six million cubic feet per minute. There are 50 main fans in operation at these mines, powered by electric motors totalling 11,200 kw (15,000 hp). The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The flow of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential. There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Ex- changer and Stobie Ice Stopes.

Jan 1, 1989

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By E. Jannoulakis

This paper introduces a practical methodology for analyzing vi¬bration records in view of improv¬ing blast designs and preempting anomalous vibrations. This technique, which is based on empirical data, uses a blasting-efficiency determinator (BED) as an indicator of vibration-energy transmission. The method was tested using data from a blasting event at an open-cast coal mine in the province of New Brunswick, Canada. The results derived from the BED values showed that geology and delay timing were probably the principal factors that induced high-intensity vibration propagation.

Jan 1, 2000

By Jon T. Langstaff

The microseismic method of detecting instability and high-stress zones in underground mines was first developed in this country by the US Bureau of Mines in the early 1940's (Obert and Duvall, 1957). Early laboratory experiments showed that when competent rocks are stressed in a testing machine, the rock noise rate (number of rock noises per unit time) increases with increasing applied stress. This increase is more pronounced as the ultimate strength of the rock is approached. Subsequent testing of rock noises in underground mines confirmed this laboratory experience and much effort has been directed in recent years to make use of this property to develop a practical method of predicting rock failure. Investigations conducted in the Coeur d'Alene district mines have pointed out a definite relationship between the stress buildup in a rock mass caused by mining activity and the emission of audible and subaudible seismic activity (microseisms). In 1968, a concentrated joint effort by USBM Denver Mining Research Center and American Smelting and Refining Co. at Asarco's Galena mine was undertaken to verify several theories regarding the generation of microseisms (Blake, 1971; Blake, Leighton, and Duvall, 1974; and Kovacs, 1973). Findings indicate that (1) rocks under stress emit detectable seismic energy; (2) the energy source can be located using a triangulation method involving travel time differences to various receiving stations; (3) the rate of release of seismic energy increases with increasing stress; and (4) this increase in noise generally precedes a major rock failure (rock burst).

Jan 1, 1979

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which' preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By R. M. Wheeler

For years the blasting industry has recognized eight milliseconds as the minimum delay time interval required between charges in order for them to be considered to fire independently of each other. However, computer analyses of seismic recordings made of several surface mine blasts reveals that this time interval may not always be sufficient for adequate vibration separation to occur. In some situations a combination of short delay periods and low frequency vibrations can result in waveform reinforcement. Various analyses of seismic recordings obtained from single hole detonations can be used to predict delay intervals that may enhance or reduce blast vibration effects.

Jan 1, 1987

By M. Plesha, A. Zubelewicz, K. Connor, T. B. Belytschko, O&apos

INTRODUCTION The Northwestern University Rigid Block Model (NURBM) has been extended to explicitly model dilatant behavior of rock joints. By incorporating dilatancy, the resistance to shear displacement and slip, which previously was limited to simple Coulomb friction, along edge-to- edge contacts is now provided by contact roughness as well as frictional resistance. The explicit formulation is based on concepts presented by Plesha (1985) in which a plasticity-based phenomenological approach was used to model dilatant joint behavior. This approach has been modified to allow for joint closure upon reversal of shear deformation. After presenting a brief description of the new joint constitutive relationship, model behavior will be illustrated with two examples. The first involves a simple two-block model to simulate a cyclic direct shear test of a single joint. The second example involves simulation of a large cavern in a moderately jointed rock mass subjected to cyclic excitation. It will be shown that in- creasing joint roughness increases cavern stability by interlocking of adjacent blocks. JOINT CONSTITUTIVE RELATIONSHIP Within NURBM adjacent two-dimensional rigid blocks interact along their common edge-to-edge contact with contact forces transmitted at the contact midpoint. The contact constitutive relationship was originally restricted to a Coulomb friction yield criterion with no tensile stresses permitted along the smooth contact surfaces. The local coordinate system for any contact is described as shown in Figure 1 with the elastic stresses and displacements related by the linear- elastic constitutive law: [ ] The contact microstructure has been modeled as Patton-type saw-tooth surfaces such as shown in Figure 2. Sliding can be active along the right asperity with angle aR and length lR or along the left asperity with angle a and length lL. In general, aR and aL will difkr as will lR and lL but for purposes of this paper it has been assumed that these angles and lengths are identical. By a simple transformation, the microscopic asperity stresses can be expressed in terms of the macroscopic contact stresses [ ] If Coulomb friction is assumed along the asperity surfaces, the plastic slip condition will be [ ] where µ is the friction coefficient with the convention that compressive stress is negative. When F is negative, the behavior is elastic and when F is zero, slip can ensure. When plastic slipping does occur, it is assumed that the relative tangential and normal displacements between the two contacting rigid blocks are additively composed of recoverable elastic parts and nonrecoverale plastic parts, [ ]

Jan 1, 1986

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices that minimize soil compaction will produce better results when forestland is the intended postmining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees. Since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree-survival rate. It is believed that these two soil-compaction parameters may ultimately be used to predict tree-survival rates on reclaimed surface mined lands.

Jan 1, 2003

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987