Search Documents

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By R. S. Austin

One-third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. Properly selected and refined, kaolin is an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By T. W. Newell

Small tonnage ore bodies can be developed at a profit on a short life basis. Such is the case of the Bardon Mine in. the Big Indian Mining District in San Juan County. Utah. Faced with a small initial tonnage of high grade uranium ore, the Shattuck Denn Mining Corporation Engineers developed some new ideas for sinking the shaft and planned extraction to warrant the capital risk to mine a limited reserve. The Bardon Mine is located fifty miles southeast of Moab, Utah in the south end of the Big Indian Mining -district. Shattuck Denn Company, a wholly owned subsidiary of the Shattuck Denn Mining Corporation, manages and operates the property under an operating agreement with Kerr-McGee Oil Industries, Inc. of. Oklahoma City. Oklahoma, and Anderson Development Corporation of Albuquerque, New Mexico. Based. on Kerr-McGee drilling., a tabular ore body about 350 feet long by 250 feet wide with an average thickness in excess of seven feet was indicated.- The ore body strikes easterly-westerly and dips from nine to twelve degrees to the south. Uraninite is the dominant uranium ore mineral associated with vanadium. The ore occurs in an arkosic conglomeratic sandstone with some interfingering of mudstone and shale in the Mossback member of the Chinle formation in contact with the underlying Cutler formation. The ore horizon is overlain with 40 to 60 feet of mudstone and shale. Fortunately, the back. immediately over the ore is a reasonable competent shaley sandstone which has made a fairly good. environment for roof bolting.

Jan 1, 1960

By T. Szwilski

The Appalachian coal region is an area here the small mining operation dominates. The large number of small operations makes the coal industry in chat area very competitive, the industry concentration ratio being low. This feature is reflected in the nature and behavior of the coal supply and demand viz a viz the coal market. The vast majority of the small coal operations in Eastern Kentucky for example, are contractors. The circumstances under which a large mining company can elect to use contractors to supplement their coal production are examined. The pros and cons of small underground single unit mines and larger multiple unit mines are discussed.

Jan 1, 1986

By H. M. von Seebach, M. P. Trubeljal, L. G. Austin

Six US coals and a crystalline quartz were tested in an instrumented laboratory high-pressure grinding rolls machine equipped with 100-mm-diam. rolls. The machine was choke-fed to maximize the capacity. As expected, the specific capacity decreased with increased grinding pressure for each material tested. Among the six coals, there were significant differences in the critical angle of nip, the effective feed porosity and the variation of strain at the gap relative to the grinding pressure. Although a precise correlation was not obtained, the overall effect of these factors was that, at a given grinding pressure, the specific capacity increased as the Hardgrove grindability index of the coal increased. The relationship between the specific capacity and the grinding pressure for a given coal was independent of feed size down to 150 µm. However, smaller feed sizes produced anomalous results, and the flow within the feed hopper was restricted.

Jan 1, 1996

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By James W. Cooksley

This report concerns a seismic geophysical exploration program which was conducted 3 miles southeast of the Carlin Mine, in Lander County, about 18 miles north of Carlin, Nevada. A twelve-fold reflection seismic line was executed over a one-mile traverse in section 32, Township 35 North, Range 51 East. This study is part of an exploration pro- gram directed toward finding Carlin-type gold deposits which are concealed under younger alluvium and volcanics. The exploration objectives of this program are as follows: 1) measure the thickness of the younger, sedimentary and volcanic deposits which overlie the "productive rock sequence", 2) delineate the Roberts Mountains thrust fault, 3) investigate the origin of the geochemical anomalies present in the western portion of section 32.

Jan 1, 1985

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

By A. M. Alfantazi, R. R. Moskalyk

Over the years, improvements have been made in the recovery of nonferrous metals, including improvements in the areas of mineral processing, pyrometallurgy and hydrometallurgy to extract cobalt as a byproduct from host minerals containing mainly nickel, copper and associated precious metals. At present, the technological emphasis is on solvent extraction coupled with electrowinning (SX-EW) for lateritic sources of supply within the Southern Hemisphere, such as in Australia and New Caledonia. Although sulfide-bearing ores, such as those found in Canada and Russia, will serve as a viable long-term source for cobalt, a ubiquitous metal, the future trend is anticipated to be in the implementation of compact and efficient SX-EW facilities that apply state-of-the -art innovation with environmental compliance This paper serves to collate the known practices for the recovery of market-grade cobalt by means of electrowinning from either an aqueous sulfate medium or chloride medium after upstream leaching, solvent-extraction and solution-purification procedures. For completeness, other commercial production techniques for the recovery of cobalt as a sulfide or oxide product are included in the summary of current cobalt processing practices.

Jan 1, 2000

By A. Yehia, J. S. Hu, J. D. Miller, M. Misra

Fluoride activation has been evaluated by Hallimond tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Experimental results of fluoride adsorption by collophanite suggest that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites. At high fluoride concentration, calcium fluoride appears to form at the collophanite surface involving a surface precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which suggest a metathetic exchange with phosphate from the collophanite lattice during the surface precipitation process.

Jan 1, 1988

By Chien D. Ngo, Andre Bachmann, Rainer Bunge

The remediation of contaminated sites has gained great importance in many industrialized countries. One method for cleaning the polluted soils from such sites is "soil washing," the scope of which is the separation of the contaminants from the soil. Soil washing is an outstanding example for a successful transfer of technology from Mineral Processing to Environmental Engineering. This presentation intends to introduce the Mineral Processing Engineer to soil washing through a short review of the fundamentals, and the discussion of an example for a successful soil cleaning operation in Switzerland.

Jan 1, 1995

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007

By R. P. King

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture characteristics of a number of single and multiphase brittle materials has been investigated using the Ultrafast Load Cell. It has been observed that very significant reductions in both fracture energies and the material integrity (damage) were achieved by heating followed by water quenching.

Jan 1, 1995

By D. W. Hendrickson

Cleveland-Cliffs views the mining process as ex- tending from mine planning to cargo loading including auxiliary systems such as materials handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This article discusses the development and results of a strategy to allow and promote implementation of process-automation improvements at individual mines based on their economic priorities, taking advantage of common systems and concepts for use at multiple mines where practical. Specific process-control upgrade projects at Hibbing Taconite Co. and the Empire Mine are reviewed.

Jan 1, 1998

By S. Nickson, M. Grenon

Oriented borehole data provide the means to characterize a rock mass. In this paper, the geomechanical caving potential of a hard rock mine project is investigated. In particular, the influence of random joints to the resulting block size distributions is addressed. The implications of this approach in preliminary investigations on the choice of mining methods are discussed with reference to one site.

Jan 1, 2003

By Henry N. Doyle

One can hardly discuss coal pneumoconiosis unless it is placed in the context of the total pneumoconiosis problem in the mining industry. However, it might be well if first we defined a few terms, since it has been my experience that the use of the word pneumoconiosis frequently causes con- fusion among those who are not familiar with the term. Pneumoconiosis comes from two Greek words meaning lung and dust. Hence, the word pneumoconiosis simply means dusty lung, or dust on the lung. There are many forms of the disease, some of which are disabling and some are not. Among the many dusts which cause pneumoconiosis might be included silica, asbestos, coal, talc, iron ore, and many other mineral dusts. Silicosis is a specific form of pneumoconiosis. It is caused by the inhalation of excessive amounts of silicon dioxide in the form of crystalline quartz. The disease is manifested by nodulation of the lungs which is apparent on an X-ray film. Continued exposure to silicon dioxide causes the nodules to grow and ultimately large areas of the lung become scar tissue which pre- vents the lung from performing its physiologic function. In its more advanced stages, there is a significant loss of pulmonary function which accounts for

Jan 1, 1966

By Ruston A. Ford

This paper reviews the development of the David Bell Mine, from early exploration, through discovery, construction, start-up, underground development, and production. Details are provided regarding the mine development, the mechanized cut and fill stope production, the proposed long-hole stoping with delayed backfilling mining method for the lower levels and the cyanide leach carbon-in- pulp concentrating process. The mine development remains on schedule and under budget with results very much as predicted in the feasibility study.

Jan 1, 1987

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008