Search Documents

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By Donald M. Duncan

An acceptable source of concrete aggregate is available in Kansas City in a continuous, medium bedded, slightly dipping limestone unit. Removal is accomplished in shallow depth, 12 feet to 17 feet high, room and pillar mines. The accepted empirical design spaces 20 foot pillars 60 feet on center. A portion of the 20 foot unit is left in place for roof support. Rock and soil cover is variable to 100± feet maximum. Long-term stability of these mines is affected by numerous factors, including the above mine-rock profile, ground water conditions and mining practice. Crusher-run aggregate sells at the mine for $2.20 per ton, yielding a gross income of $2.00 to $2.80 per square foot of mine. Use of mine space for real estate development requires a new perspective in mine development. Mining practices to obtain long term stabile structures can become an over-riding factor as compared with minimum production costs and maximum extraction ratios. Poorly mined areas are unusuable for secondary purposes. Development cost for lease space in less desirable mines is substantially greater than those planned for a secondary use. Real estate development in mine space involves unique engineering problems. Properly engineered developments offer singular advantages. Warehouse lease space sells for $.50 to $1.00 per square foot per year; fully developed office areas may double these values.

Jan 1, 1968

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987

By M. G. Karfakis

This paper examines the chimney occurrences in the Hanna Coal Field, Wyoming. Chimney caving is defined, previously proposed mechanisms involved in the development of a chimney are critically reviewed, and factors controlling chimney cave are identified. The main portion of this paper deals with the identification and characterization of chimney subsidence due to underground coal mining in the Hanna Mining District. In an attempt to characterize the subsidence, sink-hole occurrences are correlated with the depth of coal, thickness of mined-out beds, mining methods, nature of overburden, structural geology, and hydrology. Most sinkholes in the Hanna Basin appear to be conical in profile, with the apex upward. The average diameter is 15 meters (50 feet), with an average depth of 11 feet. Most have developed above an overburden of less than 61 meters (200 feet). The average mining height to width ratio is 5. Much of the chimney development is governed by the thickness and character of the overburden, the width and height of the mine opening, and the in situ state of stress.

Jan 1, 1986

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

By E. Topuz, M. J. McPherson, I. M. Konduri

The research is carried out to investigate the flow mechanics and effectiveness of face ventilation using induction fans, as an effort to provide a more efficient alternative to conventional auxiliary duct or brattice ventilation systems. The induction effects and plume longevity of fluid jets are being studied with the help of a plexi-glass model, using water as the fluid medium and creating a system that is dynamically similar to the flow in mine headings. This scaled model represents a typical 1.5m x 6m x 25m heading connecting to a crosscut. Reynolds Number criteria are used to obtain dynamic similarity of the flow in the designed model to simulate real mining conditions. The role of various parameters such as nozzle position in three dimensions, airway roughness, nozzle geometry, and flow rate in the jet are studied. During the laboratory tests, flow visualization techniques, coupled with still and video photography, were employed to identify the flow patterns. The results indicate that in typical coal mine headings, jet fans can produce effective face ventilation for distance up to 30 meters.

Jan 1, 1995

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By Stanley A. Bunk, Desmond J. Bruyns

The purpose of roasting gold ores is to release for extraction, typically by cyanidation, the small particles of gold which are surrounded by refractory stone. The roasting simply opens up passages for the penetration of solution into the interior of the ore particles. This is accomplished by the removal by volatilization or formation of volatile oxides of certain constituents such as sulfur, arsenic or antimony. Temperature is an important parameter. High temperatures tend to form a dense iron particle rather than a "spongy" calcine. The dense iron particles result in lower gold recoveries. High temperature can cause melting of some components which also results in gold encapsulation. Roasting of refractory gold ore concentrates has been practiced for decades. Multiple hearth, rotary kiln and muffle reactors were first used for roasting. Fluid bed roasting provided a low capital cost, low maintenance technology with better process control and soon became the favored technology. The first fluid bed concentrate roasters were commissioned in the late 1940's. Early fluid beds were "bubbling" type. Environmental considerations did not significantly impact on the design. Feedstocks were highly exothermic and reaction rates were relatively rapid. Roasting today must compete with other technologies for treatment of refractory ores. Ore bodies which are not

Jan 1, 1993

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By Don Macfarlane, Brian Heer, Tom Martin

The Manapouri Power Station, commisioned in 1969, is located in Fiordland National Park in the South Island of New Zealand. It is the country’s largest hydro power scheme and can generate 700MW of electricity. The power station utilizes the hydraulic head of Lake Manapouri, using an underground power station and a 10 km-long tailrace tunnel was constructed by drill-and-blast to allow discharge to Doubtful Sound. Power generation fell short of expectations due to higher than expected friction in the tailrace system. To remedy this a second tailrace tunnel was constructed between June 1998and May 2002. It consisted of a 10 m diameter, 10 km long tunnel in predominately gneissic rock and was excavated using an Atlas Copco Robbins TBM. High water inflows, Owner/Contractor production incentives and a major claim settlement were handled during the 5 1/4 year project. This paper discusses TBM advance rates, utilization factors that increased in the second half of the project plus an innovative method for sealing Tunnel 1 to construct the bifurcation.

Jan 1, 2003

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By M. S. Janssen

The development of a design equation for, and the testing of, a constant- flow airlift pump IS described. The predictions of the new airlift model agree with the results of experiments carried out using riser diameters between 0.025 and 0.300 m, submergence depths between 5 and 10 m, suspension densities between 1000 and 1650 kg/m3, and a solids dg of 70 to 100µm. The predictions o the model also agree with data from the literature for submergence depths that reached 130 m. This airlift model was employed to simulate the pulp flow through a series of tanks, each of which was fitted with an airlift pump to transfer the suspension to the next tank. Particular attention was paid to the riser diameter, submergence of the airlift pump, and control of the air supply to the airlift pump during the simulated operation of a series of tanks. The results of the simulation highlight some design parameters that could affect the efficiency and operation of a plant that employs airlift pumps to transfer suspensions.

Jan 1, 1989

By K. A. Natarajan, J. M. Modak, B. Saha

Nonliving waste biomass consisting of Aspergillus niger attached to wheat bran was used as a biosorbent for the removal of copper and zinc from aqueous solutions. Copper and zinc uptake by the biomass obeyed Langmuir isotherms. The binding capacity of the biomass for copper was found to be higher than that for zinc. The metal uptake, expressed in milligrams per grain of biomass, was found to be a function of: •the initial metal concentration (with the uptake decreasing with increasing initial concentration), •the biomass loading (with the uptake decreasing with increasing biomass loading) and •pH (with the uptake increasing with increasing pH in the range of L5 and 6.0). The metal uptake was significantly affected in the presence of a co-ion. The uptake of copper by the biomass decreased in the presence of zinc and vice versa. The decrease in metal uptake was dependent on the concentrations of metals in the two-component aqueous solutions. The effect of copper on zinc uptake was more pronounced than the effect of zinc on copper uptake.

Jan 1, 1997

By R. L. Kloberdanz

Compania Minera Disputada de las Condes S.A. (Disputada) is proactively implementing closure and reclamation planning activities at its mining and beneficiation facilities (mining facilities) in Chile where regulations governing mine reclamation are not yet fully in place. These activities are being implemented to improve currently employed measures to protect human health and the environment and to enhance reclamation and facilitate future closure with regard to these areas when mining is completed. As part of this process, Disputada, with the assistance of Shepherd Miller, Inc., developed recommendations and guidelines for future closure and reclamation of the Disputada sites. These recommendations and guidance incorporate planning and operational and post-operational design considerations and practices, and standards used by the mining industry and regulatory agencies around the world. The criteria presented in the guidance are based on achieving conditions that will be suitable for the anticipated post-mining land use. This paper discusses the process and approach taken, and the results.

Jan 1, 1999

By R. J. Miller

Mechanized Roof Supports (MRS) have dramatically improved safety and productivity of retreat pillar mining in coal. Due to low capital cost and greater flexibility, retreat panels have in some cases approached the productivity of a longwall. Because of improved safety and rapid set-up time when compared to conventional timbering, MRS are driving a return to retreat pillar mining in many situations. This paper describes how panel layout can be optimized for safety and operational efficiency when using MRS for retreat pillar mining of coal. The potential for significant unit cost reductions will also be addressed.

Jan 1, 1996

By Rogério C. Guimarães, Antonio E. C. Peres

Arafertil's oxidized ore presents barite grades that oscillate between 5 and 12%. The barite separation plays a major role in the production of apatite concentrates for the manufacturing of phosphate fertilizers. The selectivity, via flotation, in the system barite-apatite is inherently difficult due to the similarity of the physical/chemical characteristics of these minerals. The evaluation of the relevant aspects of this separation was performed based on the determinations of the electrical surface charge of barite and apatite, the abstraction isotherms of cetyl-stearyl sodium sulfate and fatty acids soaps for barite and apatite, microflotation in a modified Hallimond tube, and flotation tests in a batch column. The results showed that the adsorption of cetyl- stearyl sodium sulfate occurs preferentially onto barite, in comparison with apatite. On the other hand, the rice bran oil soap presents similar adsorption levels onto both barite and apatite. The cetyl-stearyl sodium sulfate was selective as a barite collector in the presence of apatite, a fact that was not observed in the case of rice bran oil soap.

Jan 1, 1999

By H. Köse, C. Tatar, C. Helvaci, F. Simsir

The Çayirhan coal basin is located 124 km (77 miles) west of Ankara,Turkey. With approximately 520 Mt (570 million st) of lignite reserves, the Neogene Çayirhan basin is one of the important coal districts of the central Anatolia region. The Çoraklar formation consists of crossbedded sandstone, channel fill conglomerates, mudstones, carbonaceous shales and volcanoclastic pebblestones, which are fluvial in origin. The lower and upper lignite seams occur, respectively, in the lower and the uppermost parts of the Çoraklar formation. The lignite deposits are in the Çayirhan and Koyunagili portions of the Beypazari Neogene basin. The Çayirhan coalfield consists of lower and upper lignite seams. The lower lignite seam does not outcrop at the surface. Its lateral discontinuity and relatively low sulfur content, plus sedimentologic and stratigraphic features of the associated sediments, indicate a fluvial origin. Thus, the lateral spreading and geometry of the lower lignite deposits were controlled by the channel, flood plain and well drained marshes of a fluvial system. The mining method employed at Çayirhan is the fullymechanized, retreat, working longwall with caving system. Due to ventilation, haulage and tectonic conditions, panel lengths from 0.6 to 1.7km (0.4 to 1.1 miles) are chosen, and 220-m (720ft) face lengths are used. The annual coal production is 2.2 Mt (2.4 million st).

Jan 1, 1994