Search Documents

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By F. H. Deist, J. P. E. Morris, E. Georgiadis

For some years the Collieries Research Laboratory of the Chamber of Mines of South Africa has been engaged in the development and application of computer programmes to aid in the solution of rock mechanics problems. It is the purpose of this paper to introduce some of the programmes having general applicability. A system capable of predicting stresses and displacements induced by large-scale tabular excavations is discussed. A finite element programme especially designed for handling layered continuum problems, and which is being used extensively has been supplemented by an automatic mesh generation facility that reduces problem preparation times considerably. Some typical applications of these programmes are described. An entirely new approach, potentially capable of performing linear three-dimensional continuum analysis at practical cost is introduced.

New Journals The following three journals may be of interest to readers: Fuel Processing Technology, Process Economics International, Speculations in Science and Technology, MM reports Report no. 2016 Analysis of the NIMROC reference samples for majorelements. Report no. 2018 Supergene aUeration of sulphide ores. II. The effect on the floatability of chalcopyrite, galena, and sphalerite. Report no. 2013 List of unrestricted NI M publications issued from 1966 to 1979. Report no. 2014 The determination by spark-source mass spectrometry, of chlorine and phosphorus in high-purity tungstic oxide. Report no. 2017 Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and Trompsburg Igneous Complexes. Report no. 2022 The determination of thallium and indium in sulphide concentrates. Report no. 2023 Atomic-absorption spectrophotometry with hydride generation: an improved technique. Proceedings Proceedings of the Eleventh Commonwealth Mining and Metallurgical Congress, Hong Kong, 1978. London, Institution of Mining and Metallurgy, 1979. 800 pp. 35,00 or $U.S.77,00.

Jan 1, 1979

By M. Kirsten, W. H. Botha, M. H. Fox, J. A. Moolman, A. J. Lathwood

Water is a valuable and in many areas a scarce resource. Governmental legislation regulates the environmental impact of water usage and wastewater disposal through the issue of licenses. These requirements mean that hydrometallurgical refineries must ensure that water consumption and water disposal is managed on a continuous basis in order to prevent the repeal of their operating license. Water balances are often overlooked during the design of a hydrometallurgical refinery. Recent changes in environmental legislation have forced both design engineers and operational management to review water use and disposal within these processes. Unlike concentrators where water can easily be recovered by recycling from tailing dams, water introduced into hydrometallurgical refineries becomes contaminated with soluble metals and thus requires pre-treatment prior to disposal. This paper discusses the various concerns that need to be considered during design and operation of hydrometallurgical refineries with respect to the water balance.

Jan 1, 2007

By M. B. Dunn

Terminals form part of the transportation chain from producer to consumer in the world-wide conveyance of bulk commodities. As such, they are a vital link in providing a buffer between widely differing transporation modes. It is essential in the conceptual design of such terminals that an overall view of the entire system of which they form a part is taken. Only in this way can it be ensured that the system will operate smoothly and without disruption, for in the end such disruptions can have dramatic repercussions, both on the cost of the commodity in the market place and on production. In this respect, computer simulation is a useful tool in arriving at the optimum design for the system. The Richards Bay Coal Terminal provides a good example of such an approach. Commissioned in 1976 to handle 12 Mt per annum, it is now handling 24 Mt per annum, with plans for further expansion to 44 Mt per annum in the future.

Jan 1, 1980

By M. McChesney

Modern materials for underground support* by M. McChesney The properties required of a support material for underground tunnels are discussed and, because concrete is both economical and easy to apply, a number of new reinforcing materials for concrete are examined with particular reference to these properties. From about thirty tests on different types of reinforced concrete, it is concluded that the addition of polymer to a concrete does not seem to influence the concrete's post-failure behaviour, and the on'y benefit to be achieved by this addition is to increase its flexibility (or to decrease it, depending on the polymer). Steel fibres tend to increase both the strength and stiffness of the concrete, but polypropylene fibres, although having definite loadcarrying capacities, provide non-stable failure, also known as brittle failure. The best result was obtained for concrete reinforced with steel wire: the post-cracking strength was very good and was maintained for a considerable deformation.

Jan 12, 1976

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

GENERAL Invitation to attend O.F.S. Branch Meeting: Members of the Witbank/Middelburg Branch were invited to attend a branch meeting of the O.F.S. Branch on the 15th November. The subject of the meeting would be a talk on the Hendrik Verwoerd Dam Project and up to 25 members could be accommodated on the nights of the 14th and 15th November by kind invitation of members of the O.F.S. Branch. A questionnaire would be issued at a later date, to obtain the names of those interested in attending the meeting. PAPER FOR PRESENTATION The Chairman called upon Mr G. H. J. Kitson to present his joint paper, entitled: 'Photoelectric readings; their significance for dust control on collieries.' G. H. J. Kitson (Member) and Y. J. F. Haven (Visitor). After Mr Kitson had presented his paper, both he and Mr Haven answered questions from the floor. The Chairman then thanked Mr G. H. J. Kitson for presenting the paper, and the meeting closed at 6.15 p.m.

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By J. A. L. Napier

By use of a functional model of capital expenditure developed earlier, a prototype cash-flow model is formulated as a basis for the investigation of the economic consequences when the production rate of a mine is manipulated as fundamental design variable. The optimum production capacities that maximize the common economic criteria of net present value, present-value ratio, and wealth growth rate are determined. It is shown that these choices depend certain key groupings of the economic parameters, and that they have a fixed interrelationship. The basic cash-flow model is extended further to include the effects of a constrained rate of production buildup and the imposition of State taxation on generated income. An approximation to the initial tax-free period of a new mining venture is developed, and, by use of these results, the optimum choice of production level is analysed when both the buildup rate is constrained and tax is imposed. This extended model permits a comparison between the performance of existing mines and the predicted theoretical production levels for these mines.

Jan 1, 1981

By P. N. Harris

On 23rd November, 1982, a party of 80 members of The South African Institute of Mining and Metallurgy left the Wanderers Club grounds at 07hOO, and were driven in two luxury coaches to the stainless-steel mill of Southern Cross at Middelburg. Southern Cross is a trade name adopted by MS & A (Middelburg Steel and Alloys), who operate two Alloy Divisions (at Middelburg and Krugersdorp) and one Steel Division (at Middelburg). METAL '83 The International Precious Metals Institute has scheduled a seminar on the platinum -group metals for Williamsburg, DB.A., on 10th to 13th April, 1983, and has announced its keynote speakers for each of the seminar's five sessions. Metee '83 METEC - the International Exhibition for Metallurgical Technology and Equipment with Congress - which was to have been held in Dusseldorf from 14th to 20th May, 1983, has been cancelled, and will probably take place in June 1984. Sampling Sampling and sample preparation are crucial activities in many areas of chemical engineering, in the energy and food industries, in metallurgical processes, and in mining and mineral engineering.

Jan 1, 1983

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By J. S. Freer

Two very successful schools on 'The design and operation of plants for the recovery of gold by activated carbon', were held from 14th to 18th October, 1985, and from 24th to 27th February, 1986, at Mintek. They were arranged by the Institute in close co-operation with Mr. Peter Bailey of Gencor, who was course leader. Computers and mathematics APCOM 87, the 20th International Symposium of the Application of Computers and Mathematics in the Mineral Industries, is to be held in Johannesburg from 19th to 23rd October, 1987. Interested people are invited to submit titles and synopses in any of the following topics or others. Papers can cover theoretical developments, practical applications, case studies, and software and hardware systems. Tunneling '88 The Institution of Mining and Metallurgy is pleased to announce the holding of 'Tunneling '88', the fifth international symposium and exhibition in the series, from 17th to 22nd April, 1988, at the Kensington Rainbow Exhibition Centre, London, England. Centenary exhibition and conference The major trade show to take place in the year of Johannesburg's centenary will be the 7th International Mining and Electrical Engineering Exhibition- ELECTRA MINING 86. The Exhibition, which is also the third-largest mining exhibition in the world, wil take place from 15th to 19th September, 1986, at the National Exhibition Centre, Crown Mines, Johannesburg. Mining electro technology The Eighth WVU International Mining Electro technology Conference is to be held in Morgantown, West Virginia, U.S.A., from 29th July to 1st August, 1986.

Jan 1, 1986

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

Book review Burkin, A. R. (ed.) . Leaching and reduction in hydrometallurgy. London, Institution of Mining and Metallurgy, 1975. £10. hydroxide pyritearsenopyrite NIM reports Report no. 845 A n electron-microprobe study of the nickel distribution in a serpentinite from Volspruit, Potgietersrus. (22nd Oct., 1969; re-issued Dec. 1975). Report no. 1546 Pilot-plant smelting campaign on iron ores from Tete. (22nd May, 1973; re-issued Jun. 1976). Report no. 1557 Cost estimates for the production of pig iron in the Tete district of Mocambique. (18th Jun., 1973; re-issued Jun. 1976). Report no. 1600 Dilute-acid leaching of slag from Tete ore. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1602 The roasting of Tete slag for the extraction of vanadium. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1635 Magnetic separation tests on Tete slag and ore. (30th Apr., 1974; re-issued Jun. 1976). Report no. 1671 Pyrometallurgical retreatment of a slag for the recovery of vanadium. (11th Oct., 1974; re-issued Jun. 1976). Report no. 1785 Some thermodynamic aspects of systems relevant to the flotation of sphalerite. Report no. 1808 Spectrophotometric determination (with pyrocatechol violet as chromogenic agent) of aluminium in zirconium metal and in the residue from anodesludges. Report no. 1813 The economic potential of some pegmatites from the Kenhardt area in relation to the trace-element content of their border zones. Report no. 1817 The rapid determination by X -ray-fluorescence spectrometry of tungsten in tungsten ores and concentrates. Report no. 1820 The thermodynamics of the formation of chlorocomplexes of iron (III), cobalt (II), iron (II), manganese (II), and copper (II) in erchlorate medium.

Jan 8, 1976

By R. P. King

The University of the Witwatersrand (Wits) and the minerals industry of South Africa have grown with the city of Johannesburg. The former has provided teaching and research in mining and metallurgy, while the latter has been responsible for the practical training of metallurgists and for the testing and implementation of innovative ideas proposed by the academics. This interplay between inventiveness and industrial application is illustrated by three examples: the establishment of the iron and steel industry as a result of the persistent experimentation undertaken by Professor G. H. Stanley, the first Professor of Metallurgy and Assaying at the South African School of Mines, which later became Wits; the establishment of the research organization that eventually became the Council for Mineral Technology (Mintek) - again through Professor Stanley's faith in the role of research; and the establishment at Wits of physical metallurgy as a discipline in its own right, as first suggested by Professor C. E. Mavrocordatos of Wits against the opinion of his colleagues in the industry. The Department of Metallurgy at Wits has been well supported by the minerals industry. Not only does the industry provide grants for the financial support of students, but it supplements the salaries of personnel in the Department, making possible the recruitment of top-class academic staff. At present the greatest problem is the lack of interest shown by matriculants in the metallurgical industry as a career. However, an enormous effort is being made by the Chamber of Mines, The South African Institute of Mining and Metallurgy, and the Wits Department of Metallurgy to ensure that matriculants receive appropriate information about the career prospects in the minerals industry.

Jan 1, 1983

By M. J. Nicol, P. Balestra, E. Schalch

A detailed fundamental study has been made of the various factors that influence the partial reactions comprising the electrochemical model of the cementation of gold from cyanide solutions by zinc. The effects of cyanide concentration, pH, agitation, additions of lead, and the presence of various impurity ions on both the anodic dissolution of zinc and the cathodic reduction of gold have been investigated. The results are used to explain the influence of these variables on the rate of cementation, and possible implications of this work for plant practice are discussed.

Jan 1, 1979

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

The optimization of sample spacing In South African gold mines by J. M. RENDU*, Eng. Se.D., M.S. (Min.) U.S.A. (Graduate Member) A first attempt is made at optimization of sample spacing in South African gold mines. The De Wijs model, which is shown to give a good representation of the geostatistical properties of gold values, is used to analyse the influence of the distance between samples along a stope face on the error of estimation of the stope value. The influence of other factors such as the face advance before resampling, the sample density, and the stope size, is also considered. Practical conclusions are drawn concerning the optimum sampling policy to be followed in various situations, and it is shown that sampling on a regular grid does not necessarily give the best results.

Jan 4, 1976