Search Documents

By G. P. Dyke

The MRMR classification system was developed specifically for mining applications, namely caving operations, and is one of three rock mass classification systems used in the South African mining industry today. Increased usage of the MRMR classification system has raised concerns that it does not adequately address the role played by discontinuities, veins and cemented joints in a jointed rock mass. To address these concerns, Laubscher and Jakubec introduced the In-Situ Rock Mass Classification System (IRMR) in the year 2000. Although the IRMR system is more applicable to a jointed rock mass than the MRMR system, a quantitative comparison of the MRMR and IRMR classification systems indicates that there is not a significant difference between the resultant rock mass rating values derived from the two classification systems.

Jan 1, 2008

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By D. D. Hawat

The locations of potential reserves of chromite ores throughout the world are discussed. Reference is made to the marked changes in international trade in chromite ores during the past ten to fifteen years, and to the change in locality of the production of ferochromium aloys, which is curently largely carried out in the country of origin of the ores. The influence of these changes has been very profound in South Africa, which has the largest smelting capacity and the largest production of ferochromium aloys in the world. A proportion of South African ore is stil exported to meet the demands for the production of chromium chemicals and refractories, including a large tonnage of foundry sands. Ferochromium smelters in South Africa have a capacity of virtualy 1 Mt of aloy per annum. Nearly al this development has taken place since the introduction of the argon-oxygen decarburization (A.O.D.) process for the smelting of stainless steels. Formerly, expensive Iow-carbon ferochromium aloys were required as raw materials, but the AO.D. process, which is being used world wide, permits the use of high-carbon ferrochromium, the main product of the smelters in this country. The production in South Africa of chromium-containing corrosion- and heat-resistant steels is stil on a relatively smal scale, but serious atention is being paid to the exploitation of low-carbon weldable feritic chromium steel.

Jan 1, 1986

By V-P. Takalo, M. Natsvlishvili, M. Hicks, S. Khizanishvili

"The complexity of copper-gold ores leads to large variations in recoveries and concentrate grades in the processing plant. Detailed chemical and mineralogical studies revealed considerable variation in the ratios of chalcopyrite, chalcocite, and oxidized copper minerals in the ore types studied. The end-member ore types are chalcopyrite-dominated and chalcocite-dominated, while most of the ore types plot between these end-members. In addition, increasing amounts of copper oxide and sulphate minerals result in a decreased response to flotation. Good recoveries and concentrate grades can be achieved from the chalcopyritedominated ore type, while the more altered chalcocite-dominated ore type is more challenging to enrich. IntroductionRich Metals Group (RMG) Copper in Georgia (Figure 1) produces copper-gold concentrates from two open pit mines, Madneuli and Sakdrisi, both located in the Bolnisi mining district in South Georgia. RMG and Outotec began a cooperative project with the aim of improving the recoveries and metal grades in concentrate by gaining an increased understanding of the ore variability and developing more efficient procedures for ore blending, grinding, and flotation. This type of mineralogy-led approach has already been used for other complex ores such as iron oxide copper-gold ores (Hunt, Berry, and Bradshaw, 2011), for iron ores (Lund, Lamberg, and Lindberg, 2013), and for Kupferschiefer ore deposits (Rahfeld et al., 2018).The project started with process audits and mineralogical and chemical characterization of process samples, followed by detailed chemical and mineralogical characterization of six different ore types with simultaneous flotation test work on the same samples. Since neither the recoveries nor the concentrate grades correlate with the head grades of the ores, the modal mineralogical composition, together with the ore hardness, proved to be the most promising approach in developing the geometallurgical classification of these ore types."

Apr 1, 2019

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By T. Bednarski, L. Thomas, G. Banza, D. Muteba, P. Cole, M. Soderstrom

"In copper solvent extraction, aqueous-in-organic entrainment results in the carry-over of unwanted species into the electrowinning process with negative cost implications. The need to bleed is increased and the purity of the copper cathode is potentially compromised, depending on the impurities being transferred (Cl, NO3, Fe, Mn). In some cases, entrainment results in elevated levels of manganese in the electrolyte which can cause oxidative conditions to develop and degradation of the organic phase. Degraded organic phase detrimentally affects the physical performance of the copper solvent extraction process, contributing to even higher aqueous-in-organic entrainment. Aqueous entrainment may be minimized through good operating practices and maintenance of the organic quality, but the accurate measurement of entrainment remains a challenge. This paper presents coalescing devices designed to provide more exact measurements of aqueous-in-organic entrainment. IntroductionMany copper solvent extraction (SX) plants experience high aqueous-in-organic (A-in-O) entrainments but are unaware of the extent of the problem because entrainment is often not measured. Aqueous entrainment results in the carry-over of unwanted species into the electrowinning (EW) process and the need to bleed to maintain acceptable concentrations in the electrolyte. The costs associated with the bleed are exacerbated in copper plants where aqueous entrainment levels are high. Other than these direct costs, there are operational consequences of the build-up of certain species in the EW circuit that can have deleterious effects on plant performance.Minimizing aqueous entrainment in operating plants requires an understanding of the factors that affect entrainment levels. Both chemical and operational influences are discussed in this paper. The difficulty of obtaining a representative sample makes it challenging to obtain an accurate measure of aqueous entrainment from a continuous process like SX. Coalescing devices used to get a more precise measurement of A-in-O entrainment are useful to complete mass balances around the SX circuits. Alternatively, mass balances can be used to estimate aqueous entrainments and are helpful as a tool to troubleshoot operations with a view to improving plant performance."

Jan 1, 2016

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012

By L. J. Park, A. D. Thomas

Gladstone Pacific Nickel Limited (GPNL) is proposing to develop the Marlborough nickel deposit in central Queensland and the Yarwun Refinery in Gladstone, Australia. The project proposes to connect the two sites with a DN 500, single pump station slurry pipeline, transporting up to 4 Mtpa of nickel laterite ore as slurry 180 km from Marlborough to Gladstone. Slurry viscosity is a key parameter influencing pipeline design. Not only is the slurry viscosity relatively high, requiring pumping at low concentrations, around 30% by weight, but the viscosity (yield stress and plastic viscosity) increases with shearing or agitation. It is argued that the viscosity changes can be analysed in terms of total energy input, including energy input during grinding. The slurry viscosity is therefore expected to increase along the pipeline and the pumping concentration must be low enough such that the increase in yield stress does not cause transition to laminar flow towards the end of the pipeline. The base viscosity of two ore types is determined using a rotational viscometer for minus 212 micron slurries. Viscosity variations with ore particle sizes of d99 212, 425 and 600microns are investigated. For each of these particle sizes the expected increase in viscosity during pipeline transport is simulated on a laboratory scale by agitation with a turbine mixer in a baffled container to give the same equivalent unit energy input as will occur in the pipeline. Tests were also conducted on the d99425 micron slurry in a 2.7 metre diameter DN 200Wheelstand, rotated for the 23 hour transit time and at a similar relative velocity as in the pipeline. Based on the Wheel stand test results the yield stress is expected to increase by a factor of 3.1during pipeline transit. The preliminary design allows for a reduced pumping concentration to accommodate this increase in yield stress towards the end of the pipeline.

Jan 1, 2007

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By A. O. Filmer

The techniques used in this study of the non-oxidative dissolution rates of high- and Iow-grade nickel mattes in hydrochloric acid involved leaching and the use of a rotating ring-disc electrode. It was found that the rate of metal dissolution depends on the potential at which the matte dissolves, a maximum rate of dissolution being observed at -0,2 V to 0,3 V (relative to a saturated calomel electrode). The results are comparable with those obtained in work on the dissolution of synthetic nickel and iron sulphides. The adverse effect of excess sulphur on the rate of nonoxidative dissolution is explained in terms of the mixed potential of the reaction. The leaching studies showed the feasibility of processing a high-grade nickel matte by non-oxidative dissolution, and indicate that maximum rates can be obtained in the presence of fairly Iow concentrations of oxidant. A relative selective dissolution of iron can be obtained from the Iow-grade matte under reducing conditions, thus resulting in a significant upgrading of this material. Letter to the Editor Dravo Corporation is seeking information concerning a special method of transporting explosives to aid in designing a large underground oil shale mine in the mountains of Colorado.

Jan 1, 1981

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

From its early beginnings, shortly after the Witwatersrand gold rush of 1886, Randfontein Estates was planned as a heavyweight operation. The venture was capitalized by J .B. Robinson to the tune of £2 million at time when syndicates were loath to invest £50000 in ventures in and around the new metropolis, Johannesburg, which had sprung up midway along the Witwatersrand. But by then Robinson was a colossus among his contemporaries. Operating as a loner as he had done on the Kimberley diamond fields, where he created his own individual fortune and commanded the sort of respect which, early in his career, led to his election as Mayor of Kimberley. When news of a third gold discovery in the Transvaal (the first two had been in the Pilgrim's Rest and Barberton areas) reached Kimberley, Robinson's pioneering spirit was further stired and he hastened to the new goldfield to stake his claims before his business adversaries- Rhodes, John X. Meriman, Hans Sauer, and Caldecot-could entrench themselves. Once the new Witwatersrand goldfields had been proclaimed, claimpegging started in earnest. But the question was: where to start? Diamond men al, not one of the financiers had any knowledge of the geology of the gold-bearing formations.

Jan 1, 1989

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

By W. J. Vlasblom, A. M. Talmon, A. J. Nobel

In initial laboratory tests with a travelling submerged jet on artificially prepared clay it was found that the cavity depth is dependent on the stagnation pressure of the jet and the undrained shear strength of the clay. In addition, it has been observed that the increase in cavity depth with jet pressure is stronger at higher jet pressures. It is assumed that this can be explained by cavitation of the jet at higher jet pressures. At cavitation a cone of bubbles is formed around the jet, which reduces the exchange of momentum between the jet and the surrounding water. This results in a higher jet velocity and a higher stagnation pressure at a specified distance from the nozzle exit. In literature, no relation between the jet pressure of a free submerged cavitating jet and stagnation pressures was found. Additional tests were carried out to determine this relationship. Because practical dredging occurs at relatively large water depths, these tests were performed in a pressure vessel at different pressure levels. It is concluded that the efficiency of a jet (defined as the stagnation pressure at a certain distance divided by the jet pressure), for stand-off-distances smaller than 45 times the nozzle diameter, increases significantly by cavitation in comparison to the non-cavitating situation. However, the jet pressure required for a fully developed cavitation cone increases strongly with water depth. At dredging depths of 20 m and more, the necessary jet pressures are higher than normally applied in dredging practice. Thus in spite of the importance of cavitation in laboratory tests at atmospheric pressure, in normal dredging practice cavitation is of less importance.

Jan 1, 2007

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

By G. van der Westhuizen, F. E. du Plessis

Ticor South Africa operates a dry mill at the town of Empangeni in the province of KwaZulu-Natal on the east coast of South Africa. The dry mill processes a non-magnetic mineral stream constituting rutile, leucoxene and zircon as major minerals, and minor quantities of ilmenite and other non-valuable minerals. For plant control and optimization, continuous ‘real time’ information about the mineral and chemical compositions in various plant streams is required. The current practice is to take samples at regular intervals and submit them for mineralogical(grain counting) and chemical analyses. However, these methods are time consuming, and in the case of manual grain counting, tedious and operator dependent. Until now an on-line or real-time instant mineral quantification system, which will be of great value in a plant operations environment, has not been available. Blue Cube Systems has developed a mineral quantification system using spectral mineral analysis. It measures and quantifies the composition of mineral samples instantly, providing consistent data in real time. A series of process stream samples from the dry mill mentioned above were used to evaluate the Blue Cube Systems instant mineral quantifier. This article will •describe the procedure of setting up and evaluating the Blue Cube Instant MineralQuantifier equipment •present its results, and •discuss the intended applications.

Jan 1, 2003

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By H. W. Read, L. G. D. Napier

Change is endemic in our society. Future change will be accelerated by an explosion in technology, communication, and political thought. To meet these challenges, rapid structural changes have been taking place in mining organizations both here and abroad. The management of shaft-sinking projects is a case in point. Shaft sinking is a seminal element in the sustained well-being of a deep level mining venture. Its accomplishment is fraught with risk, involves a high level of capital expenditure, and is a precursor to profitable mining investment. The purpose of this paper is to present a concise and practical picture of the concepts, methods, and techniques of professional project management as applied to shaft-sinking projects.

Jan 1, 1994

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007