Search Documents

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

A dual rate kinetic model consisting of differential equations is used to describe the kinetics of the adsorption of gold cyanide on activated carbon. The partial differential equation describing the material balance in the liquid phase is written for the special case of a fixed bed system. It is shown that an isotherm for the case of a closed system is required to yield accurate simulations of the equilibrium in a column of activated carbon. Whereas the equilibrium loading of gold cyanide is influenced by the free access of oxygen to the system, the traditional open batch stirred tank experiments, which are used to estimate parameters for the calculation of breakthrough curves for organic solutes, cannot be used here. The program solves this model at incremental heights in the column at a specific future point in time. Runge-Kutta and backwards- difference methods are used in the numerical solution. A Von Neumann method is used to show that the solution is stable. Kinetic parameters can be estimated either from batch experiments or from short column runs. In the latter method the column should not be long enough to contain the concentration wavefront for the system of interest. Results obtained from bench scale continuous column experiments were used to verify the computer model. Pure gold solutions as well as real leach liquor were used in both short column and countercurrent moving bed experiments.

Jan 1, 1987

By R. D. Cromarty, J. Du Toit

"Penetration of matte into tap-hole bricks causes detrimental refractory wear, which can lead to furnace breakouts. The ability of the tap-hole clay to form a protective layer on the brick, thereby limiting matte penetration was investigated by examining the interaction between platinum group metal (PGM) matte, tap-hole clay, and alumina-chrome refractory bricks on a laboratory scale.Samples containing clay and brick as well as samples containing clay, brick, and matte were heated to different temperatures to establish the clay-brick interaction and the extent of matte penetration. The greatest degree of physical contact between the brick and clay was achieved at curing temperatures of 600°C. Poor clay-brick contact was observed in the sample that was heated to 900°C.Matte displaced the clay in the clay-brick-matte sample that was heated to 1350°C, with significant matte penetration into the brick. Less matte penetration was observed when the clay-brick-matte sample was heated to 1500°C. Less matte penetration was also observed in the claybrick- matte sample in which the clay and brick were pre-baked at 800°C, and the sample then reacted with matte at 1350°C. IntroductionFloatation concentrate from ore from the eastern Bushveld Complex of South Africa, specifically the Platreef, Merensky, and UG2 reefs, forms the feed to the Polokwane platinum smelter (Hundermark, De Villiers, and Ndlovu, 2006). The ore from the UG2 Reef has a high chromite content, which requires high operating temperatures (1500–1700°C) to avoid chromium spinel build-up in the furnace hearth. These high operating temperatures lead to matte superheats in the vicinity of 500– 600°C, which put increased demands on the refractory materials (Nelson et al., 2005).Upon tapping, the matte moves through the tap-hole, which consists of an aluminachrome refractory brick-lined tapping channel (Hundermark, De Villiers, and Ndlovu, 2006). The flow of molten matte is stopped by the injection of tap-hole clay to form a plug in the tap-hole. The tap-hole clay hardens and strengthens during curing to obtain the required hardness and refractoriness against penetration, corrosion and erosion (Nelson and Hundermark, 2014)."

Jan 1, 2016

By H. Jeram

The ilmenite, rutile and zircon processes of the mineral separation plant generate tailing streams, which still contain valuable mineral. This is due to a combination of factors, which include separator equipment efficiency, particle size effects and inefficient operating practices (equipment overloading, blockage, etc.). Recent developments by metallurgical equipment suppliers have led to increased mineral separator performance enabling recovery of previously lost valuable mineral. Mineralogical studies were conducted using QEM*SEM and MLA techniques to identify and quantify gangue mineral species and determine mineral association. Laboratory and pilot-scale test work was then conducted to develop suitable process flowsheets for the recovery of ilmenite, rutile and zircon from current and stockpiled tailings.

Jan 1, 2007

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By G. E. Blight

Many mines engaged in deeplevel gold mining in South Africa are experimenting with the use of tailings fills, or are implementing tailings backfilling programmes on a limited scale. The approach varies from mine to mine, depending on circumstances and available fill materials. Several mines are backfilling with a cyclone underflow product; the cyclone overflow is then combined with the balance of the tailings stream and directed to surface disposal. As the extent of backfilling increases, the proportion of the surface tailings stream composed of overflow material will rise, and the properties of the tailings requiring surface disposal will approach those of the cyclone overflow. As the latter will be finer, less permeable and possibly weaker than the total tailings currently being disposed, the design and operation of surface tailings dams will have to be modified. Dams may have to be designed with flatter outer slopes of a reduced maximum height. Lower rates of rise may be required and, as a consequence, larger disposal areas may be demanded. To offset the negative aspects is the fact that the quantity of tailings requiring surface disposal will be reduced. The paper explores the dam-building properties of two cyclone overflow products. It shows that although these materials are inferior in dam-building characteristics to the corresponding total tailings, their geotechnical proper- ties still fall within, or close to, the range of properties typical of gold tailings. Although the design and operation of tailings dams may have to be modified, existing technology is adequate to handle these changes.

Jan 1, 1988

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By S. K. Gilman, P. S. Marcos

There are basic areas of importance within a concentrator or mineral separation plant, which require focus to ensure acceptable recoveries, throughputs remain at an acceptable level and product grades meet specification. Professional and para-professionals within the mineral sands industry are in demand due to the booming resource sector. Added to this, new mineral sands operations are being commissioned straining the industry further. These factors have increased staff turnover and introduced many new people to the industry. It is essential these new entrants are armed with basic plant troubleshooting skills relevant to the minerals sands industry to minimize production lost through poor recoveries. Mineral sands processing does not involve highly technical or sophisticated unit processes. However, success is often slow to arise due to a lack of detailed understanding, as well as managing multiple interrelated unit processes within a plant. Fundamental background physical conditions (such as equipment loading and water quality) must be met for unit processes to be efficient. Technical management of these process plants should always include observation of these background conditions for they often provide the answer to underperformance. Examples are presented with an indication of the possible effects on recovery and product grade.

Jan 1, 2007

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By M. Gericke

Over the past few decades the commercial application of heap bioleaching technology for the extraction of base metals has become increasingly important, due mainly to the depletion of high-grade ore reserves. Heap bioleaching is widely used for the extraction of copper from secondary copper sulphide ores. The design and engineering aspects of the process have received considerable attention, but issues related to the microbiology of the process have been subjected to less rigorous scrutiny. The major role of micro-organisms in bioleaching processes is to catalyse the regeneration of ferric iron and protons, from ferrous iron and by sulphur oxidation respectively. It is accepted that even the most carefully engineered heaps are heterogeneous in terms of temperature, pH, the presence of anaerobic pockets, irrigation efficiency, and dissolved solutes. Since interactions between solution chemistry, mineralogy, and microbial populations exist in heaps, a better understanding of the correlation between microbial numbers and types with changes in these chemical and physical profiles with time would be beneficial during process design and operation of heaps, and could result in faster start-up times and higher metal recoveries. This paper reviews the role of microbiology in heap bioleaching processes. Aspects such as microbial diversity, identification and monitoring of cultures, inoculation strategies, colonization behaviour, and tolerance to metals and salts are discussed, and the potential contribution of the knowledge to the improvement of the operation and design of heap bioleach processes assessed. Conclusions are drawn with respect to the role of genetic engineering, heap inoculation practises, and remaining areas for future heap bioleaching research and development.

Jan 1, 2012

By G. R. Sawyer

Although backfilling has been in operation for many years, the methods for selecting appropriate slurry dewatering aids have, in some cases, been rather unsophisticated. This has led to many misconceptions regarding the role of the dewatering aid and its various means of application. Testing procedures employed in the correct selection of any practically applied dewatering aid must mirror the actual working processes in which they are to be used. This constraint necessitates the development of complex testing methods when applied to backfilling. The current testing procedures were scrutinized and their various merits noted. From this study a series of testing methods was evolved which incorporate the best aspects of these testing procedures with novel ideas which would eventually result in the correct selection of the dewatering aid. A major consideration in the application of any of these methods is the modus operandi of the backfilling process, and the relevance of the tests to the process. This work attempts to consolidate the testwork performed in the past and suggest new approaches in the correct selection of acceptable dewatering aids for backfilling.

Jan 1, 1988

Newmont is one of the few remaining large mining companies that was established in the early nineteen hundreds. The company has a long, colourful and enviable history. This paper provides highlights of Newmont?s business and technical history since its inception in 1916, its transition to a ?gold only? company in the early 1990s and progress since that time up until the present day. Details of Newmonts current gold operations and its gold production profile for 2008 are also provided in the paper Over the last 50 years Newmont has developed a host of innovative gold technologies to meet the challenges of treating the complex refractory gold ores, found at the company owned mines in the Carlin region and around the world. Details of the technologies are provided and they include chlorination, roasting, bacterial and pressure leaching, leaching gold with thiosulphate and thiocyanate, N2Tech flotation, HPGR treatment of hard and abrasive ores and, finally, the use of Hydro-Jex technology for improving gold recovery from heaps.

Jan 1, 2009

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987