Search Documents

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By G. Chunnett

Platinum metal prices have risen significantly during the past 18 months, and have remained at elevated levels. Driving these bullish prices are sustained jewellery demand, mainly from the Far Eastern markets, and ongoing autocatalyst usage in response to ever more demanding global environmental legislative requirements. Within South Africa, the areas north and south of the Steelpoort River in the Eastern Bushveldare well known for their significant resources of platinum. The bulk of the resources have lain dormant in anticipation of the very situation that is currently occurring in the marketplace. Anglo Platinum is the largest primary platinum producer in the country, and is uniquely positioned to take advantage of the current elevated metal prices and shortfall in supply of platiniferous metals. In addition to its production capabilities, Anglo Platinum holds an extensive portfolio of mineral reserves and resources which underpin its ability to implement expansion projects to continue growth in platinum group metal production. It also has access to, and is actively expediting, the exploration of a range of properties where the company can further expand current production capacity or supplemented depleted production levels.

Jan 1, 2006

By C. T. Connor, O&apos

The 10th Annual UCT -US Minerals Processing Symposium was held at the Van Riebeeck Hotel at Gordon's Bay from 31 July to 2 August 1991. The conference was attended by 133 delegates representing a broad cross-section of the mining and metallurgical industry in South Africa. For the first time the Symposium, which was celebrating its 10th anniversary, was extended to two days. A cal for papers was announced and the organizers were inundated with responses resulting in a very full technical programme which consisted of 29 oral and 15 poster presentations.

Jan 1, 1991

By D. L. Morrison

The School on the Accounting for Gold, which was organized under the auspices of The South African Institute of Mining and Metallurgy by Dr Hugh E. Bartlet, Consulting Metallurgist of Johannesburg Consolidated Investment Company Limited, was held at the South African Nature Conservation Centre at Delta Park, Johannesburg, on 15th to 17th May, 1989. It was attended by 178 delegates, including 2 from the OK and 4 from Zimbabwe. A total of 19 papers were presented covering the components of gold-accounting procedure, sampling techniques, and new sampling technology.

Jan 1, 1989

Hydrometallurgical processing of complex ores and concentrates is becoming increasingly important as the mining and metallurgical industry seeks to exploit mineral deposits that are difficult to treat using conventional mineral processing and pyrometallurgical technologies. Mineral processing is often challenged by the difficulty or inability to separate valuable minerals into marketable concentrates. Hydrometallurgical processing, using selective leaching technology, can often ?chemically beneficiate? such difficult deposits. Pyrometallurgical treatment of base metal concentrates is capital intensive and subject to ever more stringent environmental control. Hydrometallurgical processing is generally lower in capital cost for an equivalent metal production rate and avoids the gas and dust issues associated with pyrometallurgical processing. The possibility of by-product recovery may also increase with hydrometallurgical treatment. Two examples of new technology or flowsheet development for treatment of complex ores and concentrates are used as illustration. These include the El Boleo process of Baja Mining for recovery of copper, cobalt, zinc and manganese from a complex clayey ore and the PLATSOL? process for recovery of copper, nickel, cobalt, platinum, palladium and gold from a bulk sulphide concentrate.

Jan 1, 2009

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

The following are available from Metal Bulletin Books Ltd, Park House, Park Terrace, Worcester Park, Surrey KT4 7HY, England. . World aluminium-a Metal Bulletin databook. 2nd ed. 1990. £71.50 surface, £76.50 airmail. This is a compendium of information listing salient details of companies mining bauxite and producing alumina, primary aluminium, secondary ingot, master alloys, and semi-fabricated products; aluminium trading companies; and a memoranda section listing associations, brand names, and other useful information. It is a userfriendly international reference book for aluminium buyers, traders, and producers.

Jan 1, 1991

By J. R. de Wet

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flowsheet development and the associated metallurgical testwork to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

By C. Norden

The purpose of this article is to show how a representative overall equipment effectiveness (OEE) measurement can be calculated for an underground coal mining bord and pillar batch process. The calculation method, the typical losses (which include planned and unplanned availability losses, coal quality losses, and process rate losses) and the underlying logic are presented and discussed. It is argued that the current traditional underground bord and pillar mining process can currently provide a maximum theoretical OEE of only 49 per cent, while a realistic benchmark target should be in the order of 37 per cent, which relates to an average of 2400 t per shift or 1.2 Mt/a. In addition, it is argued that the current bord and pillar process is the current bottleneck to further improvement past the 2400 t per shift benchmark, and that fundamental process changes will be required to eliminate this bottleneck.

Jan 1, 2012

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009

By J. A. L. Napier

The evaluation of stress distributions and deformations in the vicinity of tabular mine layouts has been carried out routinely for many years using the displacement discontinuity boundary element method (DDM). In this approach, mine layouts are approximated as irregular shaped planar cracks (or slits) where the ?width? of the crack, corresponding to the excavation height, is assumed to be negligible compared to the in-plane, lateral dimensions. Early implementations of this approach have employed square element tessellations with constant displacement discontinuity component values. This is generally restrictive when considering the analysis of irregular pillar layouts or the intersection of fault planes with excavations. This paper describes a general revision of this approach in which triangular or quadrilateral element shapes are introduced in conjunction with higher order variations of the displacement discontinuity shape functions. This facilitates an accurate evaluation of detailed stress and displacement components close to excavation surfaces and allows the investigation of local damage and failure behaviour associated with particular geological structures such as weak parting bands or weak layers. A method to embed these features in an efficient and accurate multi-level solution scheme is described. This formulation can be extended to allow the analysis of shallow-depth pillar layout problems, facilitating the assessment of the interactive response and stability of shallow depth pillar layouts. A simple deformation model is introduced to facilitate the assessment of pillar failure and bursting potential in shallow mine layouts. The computational techniques described here have been implemented in a computer code called TEXAN (Tabular EXcavation ANalyser) and are illustrated by the simulation of a particular multiple reef pillar mining problem in a shallow depth platinum mine.

Jan 1, 2007

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

This paper examines manning best practice in the Australian mining industry, comparing the mining of gold with mining of other commodities. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 7 open pit and 14 underground studies of gold mines in Australia from a database of over 50 studies. The data were collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2009. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. The proportion of supervisory to operations personnel and labour costs as a percentage of total operating costs is highlighted. Minimum manning requirements for the range of mining methods are indicated, irrespective of the size of the operation. The benchmarking results provide guidance by indicating a range of manning numbers and trends which are likely to be appropriate for the scale and type for a range of mining operations. When combined with benchmarked productivity and cost data, manning results help identify potential areas for business improvement, driving gains in the efficiency of labour. Finally, the paper considers perspectives on best practice for manning and the limitations in application of this type of analysis in a global context.

Jan 1, 2009

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By T. Feroze, B. Genc

"The ventilation of underground coal mines plays an important role in minimizing the risk of methane and coal dust explosions. The ability of ventilation, with the use of line brattices (LBs), to remove methane and coal dust in empty headings is dependent on the amount of air leaving the LB and entering the heading. The quantity of this air depends on the associated system variables, namely heading dimensions, settings of the LB, and velocity of air in the last through road (LTR). However, the exact effect of these system variables on the flow rate at the exit of the LB in an empty heading is not known. The installation of LBs in South African coal mines is generally carried out based on experience. This can result in overor under-ventilation and may increase the cost of providing ventilation or cause accidents, respectively. In this paper, using computational fluid dynamics (CFD), the air flow rate at the exit of the LB in an empty heading was estimated using full-scale three-dimensional models. The CFD model used was validated using experimental results Firstly, the settings of these three system variables were varied, the flow rates at the exit of the LB were measured, and finally the results were used to calculate the effect of each system variable. The outcome is a mathematical formula that can be used to estimate air flow rate at the exit of the LB in empty headings for any practical scenario.This paper will help the coal mining sector in South Africa by providing estimation models based on scientific reasoning for the installation of LBs, and will also serve academia as part of the curriculum towards educating future mining engineers."

Jan 1, 2016

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009