Search Documents

By Harry R. Nicholls

The objectives of this investigation were to determine the strain propagation laws for a strain pulse in salt and to compare the seismic effects from the detonation of different explosives in salt. The investigation showed that a strain propagation law of the type, e = K(R/W 1/3 ) n, and a strain energy propagation law of the type, Ea/W 1/3 = K(R/WI/3)b , are valid in salt. A change in the regression law coefficient, n , was noted with strain level. A similar change in b was inferred because strain energy is proportional to the square of strain amplitude. Particle velocity data may be used interchangeably with strain data under the test conditions.

Jan 1, 1962

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By Virginia E. Gleason

In this report, recommendations are made for programs to develop workable techniques to stop or prevent acid mine drainage formation in those underground coal mines where acid production could take place. These recommendations include development of mine closure technology, development of surface water infiltration control procedures, study of the effect of roof collapse on mine water characteristics, evaluation of the long-term effects of flooding underground mines above drainage, investigation of the effectiveness of section sealing in active mines, development of a simple model for predicting mine water quality and quantity, preparation of a manual on mine drainage abatement procedures, and development of a program to disseminate information on mine drainage abatement to the coal industry. These recommendations are based on an in-depth evaluation of information acquired over years of research on acid mine drainage formation, on numerous laboratory and field studies of methods of preventing or minimizing acid mine drainage formation, and on review of the geological, hydrological, and mineralogical factors involved. There are 772 references.

Jan 1, 1978

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

This report, authorized by a subcontract with the Crouse-Hinds Company per Section 1.1.3b of Contract Number H0220065 Amendment Number Six, and the consent of the Contracting Officer, documents the results of an investigation to develop solid state ballasts for Lucalox high pressure sodium lamps. The ballasts were to be used in the modified and new portable and machine-mounted lighting systems designed by the Crouse-Hinds Company, per Tasks I through IV of Contract No. H0220065.

Jan 1, 1976

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946