Search Documents

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By John Hays Hammond, James Douglas, J. PARKE CHAN- NING, W. R. Ingalls, J. R. Finlay

The committee making this report, consisting of Walter Renton Ingalls (chairman), J. Parke Channing, James Douglas, James R. Finlay, and John Hays Hammond, was originally appointed at a meeting of the American Mining Congress at Denver, Colo., in No- vember, 1906. The object of this appointment was the drafting of a modern law governing quarrying and metalliferous mining which could be recommended to the several States for adoption, in the hope that the passage of such a uniform law by the mining States would tend to lower the number of fatal and serious accidents. The first step of the committee (the personnel of which has re- mained unchanged from the beginning) was to procure copies of existing laws from the officials of the several States of the Union. With the assistance of the Engineering and Mining Journal, copies of the laws of Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New Zealand, and certain European countries were also obtained. The replies to the inquiries made at that time developed the fact that a number of States in which mining was carried on had no laws at all. Other States were found to have elaborate provisions regulating coal min- ing, but none applying to metalliferous mining. Still other States were found to have miscellaneous and unrelated provisions passed at odd times, seemingly as the result of the occurrence of some dis- aster or other.

Jan 1, 1915

By Thomas L. McVay

The Bureau of Mines made laboratory batch and small-scale continuous flotation tests of a sample of pegmatite rock from a deposit of the Lithium Corporation of America, Inc., near Kings Mountain, N.C., to determine the feasibility of producing commercial-grade spodumene concentrates. Various reagents and flotation procedures were tested to determine the optimum conditions for floating the spodumene and retarding the gangue minerals. The best results were obtained when sodium fluoride and lignin sulfonate were used as the pulp conditioner and oleic acid was used as the spodumene collector. The continuous flotation tests indicated that commercial-grade. spodumene concentrates analyzing 6.4 pct. Li2O could be produced with recovery of 77 pct. of the lithia in the ore.

Jan 1, 1962

Provide a coalbed methane data source for industry use in mine planning. Approach Coalbed methane data have keen collected and formatted into a computer implemented data base with software developed for storage, retrieval, and generating files of selected data in response to information requests and for statistical analysis of relationships among various coal parameters. How It Works Coalbed methane data is obtained by the Bureau's direct method test on exploration coal cores. The test involves sealing fresh coal cores in desorption canisters and periodically bleeding the gas into a water-filled, graduated cylinder to measure the volume of gas released. Coalbed methane data collected over the past 9 years have been entered into a computer-implemented data base for efficient retrieval and statistical analysis. Data base processing is accomplished with a commercially available storage, sorting, retrieval, and report writing software package (Datatrieve 11). Information requests from the coal industry are processed with the system, and the data in the desired output format am printed and forwarded to the requestor. Information such as coalbed name, location (state and county), depth of sample, gas content, and coal rank are available from the system. The data can be used for

Jan 1, 1982

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979

By Robert P. Vinson, John C. LaScola, Fred N. Kissell, Edward D. Thimon

The face ventilation measurement method developed by the Bureau of Mines involves releasing a small volume of tracer gas (SF6) on the off-curtain side of the working face at the start of the mining cycle. At the same time, gas bottle samples are taken in the immediate return airway. The gas samples are analyzed, and a curve is drawn of SF6 concentration versus time. From this curve, the percentage of gas removed per time is calculated. A curve showing a high percentage of the tracer gas removed in a short period would represent a well-ventilated face. The face ventilation measurement method was tested in a full-scale mine entry model. Subsequently it was used underground to evaluate the spray-fan ventilation system and in an MSHA test facility to test machine-mounted scrubbers. The method was shown to be a simple and effective way of evaluating face ventilation systems.

Jan 1, 1980

By Guy A. Johnson

The Bureau of Mines, through research and development contracts with the FMC Corp., has developed and tested two automatic fire sensing and suppression systems for large haulage vehicles. This work was undertaken to enhance driver safety, to lessen substantial property damage from fires on large trucks, and to increase the vehicle operator's productivity. One automatic truck fire protection system protects both the engine compartment and brake rid areas, while the second system is used in the engine compartment and fuel tank area. Both systems have redundant fire-sensing capabilities and manual override controls. Upon sensing flames and/or heat, the systems suppress the fire with pressurized, E-C class dry chemical. Both fire protection systems are flexible in design and can be modified for use on other mobile minim' equipment. Prototypes of both systems have been subjected to long-term, in-mine validation testing and actual Eire tests on 100-ton-capacity trucks at the Puma mine near Tucson, Ariz., and the Erie mine at Hoyt Lakes, Minn. During the 4-month endurance test of the first system at Pima, an accidental flash fire occurred in the test truck while it was working in the pit. The system successfully sensed and automatically extinguished the fire with no injury to the driver and little damage to the truck.

Jan 1, 1975

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

By H. S. Hardman, G. T. Adams, Will H. Goghill

"Usually a newly developed machine leaves the factory ""on a wing and a prayer."" The manufacturer hopes that the operator will hasten to report defects. In turn, when the suggestions arrive the manufacturer makes the required changes and maintains close collaboration with the operator. Thus the history of our machines of today is written.Laboratory concentration tables are exceptions to growth by experiment and collaboration. Their operation never enters directly into the cost sheet; they are seldom used for longer periods than 10 minutes; and the experimenter, while hurrying to another job, accepts the table, good or bad, for a quick test on his ore. Thus we go back about 50 years when we use the preset in factory-built laboratory table.The Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, recognized the existence of a tabling problem net usually considered. That is, instead of using the table to test the ore, the ore was used to test the table. In this critical examination of laboratory table six defects were encountered (and remedied). They are:"

Oct 1, 1945

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

By James C. Ault, Walter W. Kaufman

This Bureau of Mines manual for design of surface mine haulage roads covers such aspects of haulage road design as road alignment (both vertical and horizontal), construction materials, cross slope, and drainage provisions. Traffic control and design of proper lane widths to promote safe vehicle movement are included, as are suggested criteria for road and vehicle maintenance and for runaway vehicle safety provisions. The aim of this publication is to provide those involved with surface mine haulage road design with a complete manual of recommended practices that, if implemented, will promote safer, more efficient haulage routes.

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

By Ben A. Kornhauser

Petroleum production was the principal component of the mineral industry, followed by cement production and some salt output. The French Central Fund for Economics Cooperation loaned $9.15 million2 to the Communauté Electrique du Benin (CEB), which served Benin and Togo, toward financing the construction of a dam on the Mono River at Nangbeto, Togo. The dam was to supply hydroelectric power to reduce the energy dependence of the two countries and to irrigate crops. Nine other international financial organizations, including the International Bank for Reconstruction and Development (World Bank). the African Development Bank, the Arab Bank for African Economic Development, and the French Aid and Cooperation Fund, contributed to the estimated $140 million cost of the dam. The CEB also was to contribute to the financing. Contracts amounting to $60 million already had been awarded to West German and Canadian firms. The dam was expected to be completed in 1987.

Jan 1, 1986

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977