Search Documents

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

Reduce costs of surface mine reclamation by improving bulldozer operating efficiency. Approach A draft power indicating system helps bulldozer operators adjust blade height and other controls for maximum load movement, by continuously indicating the rate at which work is being done. How It Works This system continuously measures both the push of the blade against the overburden, and the true ground velocity of the bulldozer. It multiplies those quantities to determine the real work rate of the machine. The system consists of a velocity sensor, a blade load sensor, processing circuits, and a work-rate indicator. The processing circuits include an analog multiplier which has an output signal representing the draft power (velocity x load = power). The draft power, or pushing power is a measurement of the work rate at that moment.

Jan 1, 1979

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

Provide a central source of subsidence reference in formation for industry, academia, and government agencies interested in improving subsidence prediction and analysis under U.S. mining conditions. Approach Develop a comprehensive bibliography about mining related surface subsidence and store this information in a computer file. Make specific references accessible through a key word retrieval program. Supplement these key word identifiers by entry of author's name, title of publication, subject of text, or sponsor of publication. How It Works Requests for subsidence in-formation are made by phone or mail to the Bureau of

Jan 1, 1982

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979

By W. M. Dressel

A simple field test for detecting the presence of germanium in rocks, coals, and flue dust has been developed by the Bureau of Mines. The method consists of dissolving germanium from the samples by either acid or fusion treatment methods, adding a few drops of hematein or phenylfluorone dye, and extracting the resulting colored complex with carbon tetrachloride. INTRODUCTION Germanium is obtained commercially as a byproduct of zinc production, as a coproduct of base-metal refining from germanium-bearing mineral, and as a recovered product from the ash of some coals. The growing use of germanium in the electronics industry has increased demand for this semiconducting metal to the extent that an intensive search for new sources of supply is necessary.

Jan 1, 1962

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

Design a high-production coal mining machine with inherent low dust generation and low frictional ignition potential. Approach Constant depth linear cutting (CDLC) provides a longterm solution to excessive dust generation from shearers and continuous mining machines through new design of the rotary drum culling system. Problems with rotary drum systems, which must be eliminated to control the dust generation at the source, include the effect of a con¬stantly varying depth of cut using fixed bit spacing, secondary fragmentation of already broken coal and, frictional heating of bits and entrainment of dust by fanning action due to high drum rotational speed, Each bit on a rotary drum enters the coal face at zero depth of cut, goes to some maximum depth at the horizontal centerline during sump, and exits at zero depth.

Jan 1, 1989

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By Alan H. Goode

The advancement of high-temperature drilling fluid technology for application in geothermal environments is part of the Bureau of Mines program for more efficient development of our Nation's energy resources. The bentonite constituent of water-base drilling fluids is sensitive to destabilization by high-temperature and salinity. A substitute material for bentonite, phosphate slime, which is reported to be saline resistant, was considered. These studies show that spray-dried slime suspensions have more favorable rheological behavior, but poorer filtration properties, as compared with bentonite suspensions.

Jan 1, 1975

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984