Search Documents

By Carl E. Norman

An investigation of geologic structure on macroscopic, mesoscopic, and microscopic scales was conducted on near-surface igneous and metamorphic rocks in which the existing stress field was determined by in situ methods. A consistent NE-SW orientation of the maximum compressive stress in the horizontal plane at four of five test localities appears due to the intrusion of NW-trending diabase dikes. Structural features at the mesoscopic scale show no consistent directional relationship to determined stress directions. Petrofabric diagrams of open microfractures show preferred orientations, but these are not consistently related to the orientations of larger structural features, such as joints, foliation, or mineralized shear zones. However, at five of six test sites the preferred direction of microfractures occurs nearly perpendicular to the maximum principal stress directions; an anomalous parallel relationship exists at a test site in an intrusive rock body. The results suggest that the open microfracture subfabric may provide a means for gaining information on the directional properties of stress fields. Such information can be obtained from oriented cores taken from holes which exceed the approximate 100-foot depth to which other in situ methods are presently limited.

Jan 1, 1970

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By James J. Olson

The Bureau of Mines recorded both particle accelerations and velocities from one-stick and production blasts at Eagle-Picher Industries' Shullsburg mine, Shullsburg, Wis., to test the effectiveness of square root scaling in grouping underground blast vibrations and to determine the effects of rock type and mine geometry on blast vibrations. Although the charge weights of subsequent delay periods sometimes exceeded the charge weight of the zero-delay period, both acceleration and velocity records showed that the zero-delay portion of the Shullsburg production blasts produced the highest vibration amplitudes. Because of the restricted range of charge weights in the Shullsburg experiments, no statistical determination of an appropriate scaling factor could be made. However, the square root scaled peak particle velocity data from the Shullsburg production blasts grouped well within the approximate band-width of vibration data obtained by the Bureau from quarry blasts in many different rock types. This indicates that scaling by some factor, perhaps the square root or cube root of the charge weight, may be an effective way to group and study vibration data from underground blasts. Further research is needed to determine which scaling factor is best for underground blasting.

Jan 1, 1970

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of the Ohio coalfield. Washability analyses were made on 39 coalbed samples collected from a 14-county area. None of the samples were of metallurgical quality as received. Nine of the samples could be sufficiently upgraded to produce metallurgical-grade products, and the remaining 30 samples could not be upgraded to this quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 10 of the samples were of medium sulfur content as received and one could be upgraded to a low sulfur content. Of the 29 samples having a high sulfur content as received, 18 could be upgraded to a medium sulfur content. The original sulfur content of the other 11 samples having a high sulfur content as received can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as high sulfur coals both before and after removal of the sink 1.58 specific gravity material.

Jan 1, 1972

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

The head loss data for coal slurries over a range of concentrations and velocities and the laboratory screen analysis were selected as areas for investigation in the data analysis performed. The analysis resulted in the following: (1) Size distributions for the coal used in the horizontal pipeline tests were fitted to the Rosin - Rammler distribution function. Each of the fits was significant. Corresponding Rosin - Rammler parameters were obtained which were introduced into the regression analysis. (2) A regression equation was obtained which predicts the slurry head loss of 1-inch by 0 coal slurries ranging in volumetric concentration from 20 to 40 percent and line velocities from 1 to 14 feet per second as a function of the square of velocity. The addition of the term for concentration in the regression equation did not contribute significantly c head loss.

Jan 1, 1972

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971

By M. M. Fine

This report describes a Bureau of Mines technical feasibility study of simultaneous reduction and induration of pelletized iron ore to make a product with superior qualities as blast-furnace feed. Highly reduced, physically competent pellets can be made from magnetite and specularite concentrates that contain small additions of bentonite as binder. In batch tests, pellets were dried, surrounded with solid fuel in crucibles, and heated to the reducing temperature. Total iron content of the best products was higher than 80 percent and crushing strength of 1/2-inch metallized pellets ranged up to 600 pounds or more. Comparative tests of several commercial oxide pellets showed a wide range in crushing strengths, but most values were less than 350 pounds. Continuous tests in a rotary kiln resulted in the same degree of reduction, but the pellets had lower crushing strengths because of the limitations in the maximum operating temperature of the small kiln.

Jan 1, 1962

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By Susan B. Bealko

Mining provides a large part of the energy and raw materials that feed this Nation's economy. Copper pipe, concrete, and window glass serve as well known examples of the reliance on minerals in modern society. Less appreciated, but as important, are the hundreds of mined commodities that are an integral and necessary part of everyday products, ranging from medicines and computers to carpet and paper. Coal is a major portion of the country's energy mix today, as it will likely continue to be in a future hydrogen-based economy. The domestic mining industry also provides strategic minerals that are important for the Nation's security. The processes to recover these mineral commodities are among the most demanding and complex in an industrial society, and this inherently dangerous industry has historically had the highest risks of fatality and injury. The mining industry has been undergoing some trying and challenging times because of the recent mine disasters in the coal fields. These events have been alarming in light of the strong and encouraging safety record that has characterized mining in the United States for most of the past decade. While mining communities deal with their grief, mine operators, government regulators, and other safety personnel, set about trying to determine why these fatalities occurred. Subsequently, the mining industry is currently experiencing changes in legislation at an unusually rapid pace. The most recent regulatory changes are the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) and the temporary emergency standard for mine seals. The new mine safety laws call on the nation's mines to adopt certain procedures and safety technologies immediately, or as soon as they become commercially available. Putting all the provisions in place from these new laws is a major undertaking, and will necessitate strong collaborations and partnerships among mine operators, manufacturers, regulatory and research agencies, labor unions, and community groups. It is against this background that Prevention through Design (PtD) components for the Mining Sector are recommended.

Jan 1, 2008

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By Charles Prasky

This report describes bench-scale studies and pilot-plant development of the Bureau of Mines process for roasting iron ores with a ferrous scrap reductant, such as discarded automobile hulks, to yield artificial magnetite. Quality magnetic concentrates containing about 66 percent iron and 6 percent silica with iron recoveries of over 90 percent were obtained after roasting fine-grained oxidized or nonmagnetic taconite with unburned, sheared automobile hulks in a rotary kiln. The relatively complete oxidation of the lighter gage metal in the automobile during roasting resulted in a metallic byproduct consisting of the unconsumed heavier gage metal scrap. This residual or tailored scrap is potentially useful as heavy melting stock and has more value than the original automobile hulk.

Jan 1, 1970

By D. B. Dow

The transportation of any commodity which is actually or potentially a source of fire or explosion, has been made safe, insofar as humanly possible, by rigid requirements as to inspection mechanical safety devices, and by printed labels. For the most part these precautions have been sufficient. This is evident when it is considered that in the thousands of instances in which commodities with a great fire risk have been transported, few disasters have occurred. This paper deals with the recent gasoline explosion which occurred at Memphis, Tennessee. At 7:50 a.m. January 24, 1921, vapors from a tan: car of gasoline became ignited and resulted in a blast that killed eleven people and badly injured nineteen others. Probably forty or fifty men, women, and children received slight injuries from falling debris or from burns. The explosion wrecked an oil plant, leveled a block of frame buildings, and broke window panes within a radius of five blocks.

Feb 1, 1921

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008