Search Documents

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By Thomas M. Barczak

This U.S. Bureau of Mines study evaluates factors that influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: longwall panel, powered roof supports, and gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from convergence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data sumest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 2010

By W. R. Wrzensinski

This report presents the findings from a l-yr Bureau of Mines program in which sulfur concrete reinforcing materials were tested and evaluated to determine their resistance to corrosion. It also summarizes the permeation characteristics of sulfur concrete and the exemplary performance of precast, reinforced sulfur concrete structures in various industrial environments. The Bureau is furthering the development of sulfur concrete technology as part of a larger effort to find uses for the Nation's plentiful sulfur resources in construction materials. Sulfur concrete is a corrosion-resistant material that can be used in acid and salt environ-ments where conventional materials fail. Penetration of corrosion-inducing agents is minimized because of the low permeation characteristics of sulfur concrete.

Jan 1, 1988

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By L. D. Stewart

The main reasons for developing an induction system for signaling from the cage are, first, to increase safety, and second, to effect economies in the operation of cage and ship hoists, especially when work is being done in the shaft. To-day nearly all mines which employ safe methods have installed safety gates on cages, at the different levels, and at the collar of the shaft. Under the old system in some instances signals could only be Given from the station outside the cage, and in other cases, after the signal was given the only method whereby those riding on the cage could control its movements consisted of pulling the bell-rope hanging in the shaft, an uncertain and somewhat hazardous procedure at best. With the system herein described, however, it is possible, without opening the gates, to signal to the engineer from any place in the shaft whether or not the cage is moving, and finder the same conditions it is possible to converse with the engineer by using the telephone. In short, the cage tender has at all times an opportunity either to signal or talk to the engineer without leaving the cage.

Jan 1, 1931

By F. B. Tough

An inusual job in controlling a gas well was executed on No. 1 well, Inland Oil and Refining Co., situated on the Alkali Butte structure, Freemont County, Wyoming. The work was done by the company in cooperation with the . S. Bureau of Minos, and resulted in a fuel saving of $5,000 in one season and of a repair job estimated at $15,000, or a total of $21,000. The woll had an open flow of 6,000,000 cubic feet of gas per day with a rock pressure of 560 pounds per square inch. A string of 6-1/4 inch casing with a toothed shoe was set on the cap rock above the gas sand at 2181 feet. Then the well was shut in, the gas worked out around both the 6-1/4 inch and 6-1/4 inch strings, breaking through the ground surface at several points under the derrick. Casing troubles encountered while drilling made it unsafe to attempt Coving the 6-1/4 inch string. Moreover, it was important from the standpoint of good management to make the gas from this well immediately available for fuel in other operations and, in addition, to save the gas from wasting. An ordinary mudding and cementing job would have necessitated sitting down this well for probably two months out of a very short operating season. For these rousons it was determined to mud the well, if possible, between the 6 and 8 inch strings by pumping mud fluid through the connection from the gas clamps. The gas clamps used wore of ordinary construction with a side outlet, making them equivalent to a Braden-hoad. When the mud fluid was pumped through the gas clamp into the space between the two strings, it began to appear inside the 6-1/4 inch string. It apparently entered the well either around the toothed shoe or through a "line sawed" leak in the string and was blown out of the well as fast as it was pumped in. In order to stop the leaks, about a half a gunny sack of finely chopped bull ropa was fed with the mud between the casings as before. The hemp gathered around the valves of the mud pump to some extent, and it also stuck in the casing-head fittings a few times. An obstruction in the casing- head would be removed by permitting the woll to "blow back" for a few seconds, and one in the pump valves, by removing the valves when necessary. In two days' time sufficient hemp and mud had been pumped into these strings to kill external and internal pressure. The wall was shut in and allowed to stand over night. The next day, by opening and closing the master gate at intervals,

Mar 1, 1921

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By Kevin Connor

The Government's ban on all commercial mining operations, except for small-scale artisan exploitation of alluvial gold deposits, continued throughout 1985. Minerals produced were kaolin and lime for agricultural uses, and experimental peat harvesting for energy applications. The total value of the minerals produced during the year was estimated at $1.1 million .2 In early 1985, an agreement between the Government and Amoco International Oil Co. was ratified for a petroleum exploration concession covering 248,000 hectares of Lake Tanganyika. Onshore exploration in the Ruzizi Plain was already under way the last half of 1985. By yearend, enough seismic information was available that Amoco hoped to complete data analyses, determine onshore drilling sites, and begin drilling operations before the end of 1986. Also to begin in the latter part of 1986 were seismic studies of Lake Tanganyika. Throughout 1985, Amoco officials were negotiating with the Government of Zaire for expanding the exploration acreage into that country's portion of northern Lake Tanganyika and the Ruzizi Plain. An agreement between Amoco and Zaire could have important beneficial economic implications for both Zaire and Burundi, and onshore seismic work in Zaire logistically supported from Bujumburi could begin almost immediately.

Jan 1, 1987

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

By J. B. Janus

This report, the 25th in a series, lists analytical data of coal samples collected by the Bureau of Mines in connection with the purchase of several million tons of coal for various Government agencies during fiscal year 1975. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for these coalbeds only. The delivered coal was sampled at destination in accordance with instructions furnished by the Bureau of Mines, and all samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1976