Search Documents

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

By Jerry W. Stengel

The Bureau of Mines subjected two manufacturers' chemical oxygen (K02) self-rescue breathing apparatus to a series of laboratory environmental treatments designed to simulate various conditions in underground coal mines. The environmental treatments consisted of extremes of temperature, shock, and vibration. The tests were designed to be used as predictors of the ability of the self-rescuers to survive those environmental insults with no degradation in their protection to the wearer. Based on the severity of the treatments, simulating conditions more severe than offered by the mining environment, the two apparatus tested should be able to withstand the abuse offered by the mining environment and still function as intended in an emergency. Correlation of these tests with results of long-term field evaluations is needed to provide confidence in the laboratory tests as predictors.

Jan 1, 1982

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Howard C. Turnage, Dana T. Updyke, Wayne C. Muhler

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leaky feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 6, 1980

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping &apos; compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

By Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

Problem: Incident investigation reports do not usually contain enough information to aid in studying boom arm vertical speed for roof bolting machines to determine the impact that appendage speed had on an operator&apos;s risk of experiencing a contact. Laboratory experiments with human subjects are also not feasible because of safety and ethical issues. Method Researchers successfully developed a three-dimensional computer model that uses virtual human simulation software as the primary means to gather contact data when the boom arm touches the operator&apos;s hand, arm, head, or leg. Results: Data analysis of roof bolter simulations shows that the speed of the boom arm is the most important factor in determining the risk of an operator making contact. Regardless of other variables, contact incidents were always greater when the bolter arm was moving up, greater on the hand, and greater for the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom arm is ascending. Based on the data collected, boom speeds greater than 13 in/sec result in a substantial increase in risk to the roof bolter operator of making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Impact on Industry: The use of such information can be quite helpful in making recommendations to machine design and task procedures to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine&apos;s boom arm.

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By E. W. Dean

The Bureau of Mines is engaged in the work of obtaining data regarding the physical and chemical properties of typical crude oils from the various producing fields of the, United" States. Preliminary reports have been published that cover the eastern fields* and the&apos; Rocky Mountain districts.** Since the appearance of these, reports: it has been suggested that certain additional data. I regarding the samples would be of practical value. It was believed that a knowledge of the viscosity of crude oil was desirable, particularly in connection with the design and operation of pipe lines. In accordance with this suggestion, the authors have made viscosity tests upon as many of the samples of the two series as wore still available for examination. Determinations were made at temperatures of 70° and 100°F., and in addition the oils were Subjected to the A. S. T M, pour-test*** to as certain the lowest temperatures at which they remain in a fluid condition.

Jan 1, 1921

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau&apos;s technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner&apos;s breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

By Launa Mallett, Charles Vaught, Michael J. Brnich, R. Lincoln Derick

After thoroughly covering the health and safety training subjects required under Title 30, Part 48, of the Code of Federal Regulations (CFR), mine operators often find themselves with little or no time left in the class schedule for other important topics. This paper discusses a technique developed in partnership with RAG Twenty mile Coal Co., Oak Creek, CO, for incorporating employee participation at all levels in fire prevention and safe equipment operation training outside of traditional classrooms. The process involves development of training modules consisting of short, 5- to 7-minute videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner’s workplace.

Jan 1, 2002

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By H. Schultz

Urban refuse that was mechanically separated at the U S Bureau of Mines pilot plant in College Park, Md., was successfully evaluated for its fuel values using standard coal analysis methods. Analyses performed on refuse samples taken from five sample points included moisture, ash, sulfur, chlorine, and heating value. It was recommended that characterization of the combustible portion of urban refuse by standard coal analysis procedures should be widely adopted.

Jan 1, 1975