Search Documents

Objective To improve seats on mine shuttle cars with ergonomic design and by reducing shock impact transmitted through the mine vehicle seat to the vehicle operator. Background Operators of underground mobile equipment, particularly shuttle cars, are often exposed to significant levels of shock and whole-body vibration. Past studies have reported that as many as one-third of underground equipment operators could be exposed to adverse levels of shock and whole-body vibration. Moreover, seats on mining equipment, historically, are inadequate relative to the ergonomic needs of the equipment operator. In the extreme, amine vehicle seat has sometimes consisted of blocks of wood or a bent steel plate bolted to the machine frame. Also, the lack of sufficient vertical clearance in some underground mines is an impediment to providing adequate shock isolation systems on mine equipment seats. Approach The NIOSH Pittsburgh Research Center (PRC) is conducting research with viscoelastic foams to improve seats on mine shuttle cars. Viscoelastic foams were used in an ergonomically designed seat to reduce the amount of shock transmitted through the mine vehicle seat to the vehicle operator. Data on selected viscoelastic foams were analyzed from laboratory shock tests at PRC. Using information from the analysis, two ergonomic seats incorporating selected foam were constructed for in-mine testing on a shuttle car (Joy 21SC) in eastern Kentucky. The shuttle car operated in a 35-in-thick coal seam with an approximate mining height of 43 in. Operational data were recorded on the ergonomic and original seats. Further, the shuttle car operator was asked to compare these seats. Results When comparing the original seat (figure 1) with the ergonomic seat (figure 2), the shuttle car operator described the ergonomic seat as generally “much better” than the original seat. The operator explained. “It’s just easy to adjust. And it’s got the lower lumbar support. And the pad is thicker. It’s just much better all the way around.” He added, “It does support you more and [there is] less shock when you hit a hole...I liked the lower lumbar support. That’s where most of your shock is at, in your lower back.” The operational data supported the operator’s comments. In the full-load case, significant improvements in isolation were achieved(down to 15 Hz) with the ergonomic seat. Additional laboratory testing of seven viscoelastic foams was done to further improve the level of isolation from shock and better characterize the material properties of each foam. Data from this testing were used in an analytical model of the seat pan isolation system. Results showed that two of the viscoelastic foams, SUN-MATE EXTRA-SOFT and PUDGEE, gave the most effective shock isolation of the seven materials tested. A composite of EXTRA-SOFT and PUDGEE foams improved the isolation characteristics of the seat pan to approximately 4 Hz. Similarly, EXTRA-SOFT by itself provided isolation to 5 Hz. These results will be validated with future in-mine measurements. Cooperative Research Opportunity NIOSH is seeking cooperators to assist in further research and development of this technology. Additional information on cooperative reseach may be obtained by contacting Jacqueline H. Jansky, Technology Transfer Officer, NIOSH Pittsburgh Research Center, P.O. Box 18070, Cochrans Mill Rd., Pittsburgh, PA 15236-0070, phone: (412) 892-6615, fax: (412) 892-6678, e-mail:jgj7@cdc.gov

May 1, 1997

By F. R. McDonald

The compound ?-valerolactone has been identified in an acid fraction isolated from waste water collected from an in situ oil-shale retort. Infrared, nuclear magnetic resonance, and mass spectrometry were used by the Bureau of Mines to confirm the identification of a subfraction collected from a gas chromatograph.

Jan 1, 1974

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By T. J. McDonald

The methods used and the results obtained in the application of high-expansion foam on a recent fire in an operating mine in western Pennsylvania were reviewed. This is the first instance where foam has been applied extensively to a fire under actual mining conditions although considerable research has been conducted and experimental fires have been controlled. The Bureau of Mines began investigating the foam-plug technique in 1957 in its experimental coal mine, following reports of successful trials in Eng-land, where the basic methods, using the normal ventilating current, were developed. Early in the research it was apparent that the normal ventilating current in mines in the United States would not provide adequate air pressure to drive a foam plug the distance that might be required. Subsequently, the Bureau of Mines developed a portable high-expansion foam generating unit consisting of a fan having relatively high pressure potential, net, sprays, and metering equipment. To date, foam generators have been constructed by the Bureau, by at least one operating coal company, and by one manufacturer of safety equipment. A number of units from the latter supplier have been adopted by coal-mining companies as an integral part in their firefighting installations.

Jan 1, 1961

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

By John A. Davis, John Gross

Six tests were made by the Alaska Station of the Bureau of Mines on a sample of black sand delivered to the station by Messrs. James, Eagan & Griffen from Fairbanks Creek, Fairbanks mining district, Territory of Alaska, to devise a method of recovering the gold content. More than 90 per cent of this black sand consisted of magnetite and garnet which can be separated magnetically. The Station has no equipment for magnetic separation other than an electromagnet similar to the one used by Day and Richards, (Day, D.T., and Richards, R.H., Investigations of Black Sands from Placer Mines, U. S. Geol. Survey, Bull. 285, 1906, pp. 150-163), which can only be used satisfactorily on small samples. To treat the entire lot of black sand with this machine would have been impracticable. Therefore only a small part of the sand was so treated, the rest being divided into five lots in order to obtain comparative results from other methods of treatment.

Aug 1, 1920

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By Charles W. Huggins

The Bureau of Mines investigated palygorskite, a natural asbestiform material, to accumulate knowledge that might serve as a foundation for future synthesis of a similar material. Unit cell, chemical analysis, DTA, TGA, optical constants, and electron microscopy data were obtained. Selected palygorskite samples of bettor than 97-percent purity were used to obtain this information. Chemical analysis revealed the following formula: (OH2)4 (OH)2 Ca0.01Fe0.02K0 .c3Mg2.10A12.00Si7.93020.3.91 H2O. The optical constants for sodium light are a = 1.522; S = 1.530; ?=1.533; biaxially (-). The following orthorhomibic unit cell constants were determined: ao = 12.690 A, Z = 2, bo = 17.857 A, Dx = 2.327. co = 5.207 A, Identical diffraction patterns resulted from the three palygorskite samples that were studied. X-ray, chemical, DTA, TGA, and optical data were compared with literature values for similar fibrous materials. X-ray diffraction lines were indexed. Several electron micrographs were made to compare the structures of palygorskite and attapulgite with that of chrysotile. The micrographs revealed extremely short laths for attapulgite, very long flexible laths for palygorskite, and tubular structure for chrysotile.

Jan 1, 1962

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

By Herbert R. Appell

Urban refuse, cellulosic wastes, and sewage sludge have been converted to heavy oil by heating under pressure with carbon monoxide and steam. Conversions of the organic matter to oil, water, and gas have averaged near 90 percent at temperatures of 250° to 400° C and pressures of 1,500 to 5,000 psi. The yield of oil, based on the dry organic matter of the waste materials, is usually near 40 percent. This is the equivalent of more than 2 barrels of oil per ton of dry, ash-free waste material. The oil from urban refuse and cellulosic wastes has a sulfur content near 0.1 percent. This low sulfur content makes the oil from refuse a desirable source of fuel oil.

Jan 1, 1970

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By Ann G. Kim, Thomas R. Justin, John F. Miller

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, PA. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic test and subsurface temperatures was not significant.

Jan 1, 1992

By Loyal Clarke, H. H. Storch

"The discovery of large deposits of polyhalite (K2S04.MgS04.2CaSO4.2H2O) in Texas has led to an investigation of possible industrial proecsses for the extraction of potash from this material. This mineral was first discovored in small quantities in the European potash deposits in or about the year 1800. Chemists fire thought it to be a form of calcium sulphate, but a more accurate analysis by Strohmiyer indicated the composition as given by the above formula.The decomposition of polytalite by aster is very slow and results in the formation of a layer of gypsum at the surface of the polyhalite which retarts the solution of the potaseium and magnesium sulphates. To obtain a substantial yield of K2S04 in solution it is necessary to use large amounts of water at room temperature, for he concentration of K2S04 is limited by the low solubility of syngonite (K2S04.CaS04.H2O) whereas at 100º C. several days boiling are necessary to obtain more than a 6 per cent K2S04 solution even when finely powdered polyhalite is employed.In 1854 H. Rose discovered that calcination, followed by leaching with water, resulted in a larger extraction of the potassium and magnesium sulphates, as compared with leaching without precalcination. During the course of a series of investigations concerning formation of oceanic salt deposits, Van't Hoff and his pupils obtained sufficient data to construct the equilibrium diagram for the system K+Mg+SO4--Ca++.H2O for 25° C. and for 83° C. These data are very well summarized. in the International Critical Tables' and by Boeke and Eitel. From a consideration of the diagrams for 83º C. one would conclude that an extraction of polyhalite with moderate amounts of water at 33º C. would result in a solution whose maximum concentration of K2So4 would be about 3.6 grams per 100 grams of water and of M2SO; about 4.0 grams per 100 grams of water, corresponding to equilibriumwith the solid phases: Polyhalite potassiam-calcium pentasulphate and anhydrite.The fact that it has been found possible to obtain as high as 11.4 grams of K2S04 per 100 grams of water (see table 6) and an equivalent amount of MgSo4 (8.1 grams per 100 grams of water was obtained corresponding to a ratio K2/Mg of 0.98; indicates that the formation of these complex salts is very slow. To be sure, this results was obtained at 100° C. instead of 83º C. However, the work of Anderson and Nestall 9 on the double salts of calcium and potassium sulphates at 100º C. indicates that the diagram at 100º C. C. would not be greatly different from that at 83º C. This slow rate of approach to equilibrium when combined with precalcination of,of polyhzli-,a is the 17,asis of some of the more p:olisinE methods of extracting potash from polyhalite."

Jun 1, 1930

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973