Search Documents

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By E. M. Kawenski, J. K. Richmond, M. J. Sapko, G. C. Price

This Bureau of Mines publication presents investigators' reports of all major coal mine explosion disasters that occurred in the United States from 1959 through November 1981, along with a brief analysis of common factors in these disasters, The report reviews the Federal mine health and safety acts of 1969 and 1977, and discusses how implementation of these acts has reduced the number of both fatalities and disasters, Current Bureau health and safety research is summarized, and an appendix lists most of the ignitions and explosions in the period of record,

Jan 1, 1983

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

This report, which updates and supersedes the Office of Surface Mining's 10-year progress report published in 1987, deals with the accomplishments of the regulatory and abandoned mine land reclamation programs during the first 15 years of the Surface Mining Control and Reclamation Act of 1977 (SMCRA). Part 1 is an illustrated description of on-the-ground accomplishments; Part 2 presents statistical information for the 15-year period. The data in this statistical report are organized in two sections: national statistics and state statistics. The national statistics provide an overview of coal mining and the implementation of SMCRA since 1977. The information reported for the states presents a brief description of the coal reserves in each area, accompanied by detailed statistics and graphs that relate each state to the nation as a whole. The statistics compiled in this report are from the Office of Surface Mining's files, computer data systems, and annual reports. During the early years of the program, many of the data categories were evolving and changing; therefore, data reported over the 15-year period are not complete for all states for all years, and where data was unavailable or zero, a dash (-) is shown for that item. The data sources used to compile the tables and graphs are listed and described in detail on page 76. Due to the number of requests for this information in the past, statistical information about coal mining and its regulation will be available each year as an appendix to the Office of Surface Mining's Annual Report to Congress. Beginning in Fiscal Year 1993, this information will be compiled and published on an annual basis. For more information about this report, call or write the: Public Affairs Office Office of Surface Mining 1951 Constitution Ave., N. W. Washington, D.C. 20240 (202) 208-2553

Jan 1, 1992

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude oils from producing fields in the United States and has published a series of reports on different fields, including oil fields of Texas3. Production Data The Spindletop field was discovered in 1901 when the pay sand was found at deaths of about 800 feet. During the following twenty-five years a number of attempts were made to find a deep productive sand. All attempts sere failures until a roll drilled by the Yount Lee Oil Company found oil late in 1925. An intensive drilling campaign began at once, and the production of the Spindletop field increased to a daily average of 93,217 barrels in September, 1926; the present production is estimated at 66,000 barrels doily. Tile following table taken from the Oil and Gas Journal for February 10, 1927, shows the daily average and the total production by ninths for 1926.

Jan 1, 1927

By Causey J. Douglas

In 1988, at the request of the Bureau of land Management, the U.S. Bureau of Mines studied part of the 13,460-acre Owyhee Breaks Wilderness Study Area (OR-003-059) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. No mineral resources were identified in the study area during this investigation. There is an occurrence of jasper along Birch Creek and an associated occurrence of zeolite in some tuffs. In the northern part of the study area is an occurrence of bentonitic clay containing less than 40,000 tons. Much of the area is covered by landslide blocks, colluvium, earthflow deposits, and talus, composed of Tertiary-age volcanic rocks. The upper plateaus are capped by Tertiary-age basalt.

Jan 1, 1989

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

By Richard F. Hewlett

Use of digital computers makes possible a more efficient and complete analysis of data from a mineral deposit . This computer program was written and used during an investigation into the efficiency of methods of computing grade and tonnage of ore , wherein it was necessary to make repeated computations involving different combinations of data . This investigation was part of a continuing program of sampling methods research at the Bureau's Denver Mining Research Center.2-4 This program is designed to compute tonnage and average grade for 40 cutoff grades using either the statistical or polygonal methods . tational rate is from 200 ( input bound ) to 1,400 assays per minute , depending on the use of either individual ( one assay per card ) assay- interval length or

Jan 1, 1963

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By R. V. Lundquist

The Bureau of Mines made a laboratory study of the amenability of anorthosite rock ( from the San Gabriel Mountains , Los Angeles County , Calif . ) to treatment by the lime soda sinter process for the extraction of alumina . The study was done under a cooperative agreement with the California Division of Mines and Geology . This report presents the results of the investigation , and it includes a review of the geology of the deposit ( 7 ) by Dr. Gordon B. Oakeshott . Interest in the recovery of alumina from submarginal aluminum silicate ores is stimulated by the fact that the domestic aluminum industry depends on imports of bauxite for its alumina requirements . Of the 8.0 million long dry tons of high - grade bauxite consumed in 1961 for producing metallurgicalgrade alumina , only 0.9 million long tons , or 11 percent , was mined in this country . During past years many organizations have carried out research programs to determine if alumina could be extracted economically from such domestic ores as clays ( 3 , 4 ) , anorthosite ( 8 ) , and other silicate sources . Successful alumina extraction is the ultimate objective of the Bureau of Mines program.

Jan 1, 1963

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By R. B. Moore

The story of helium is one of the romances of science . Probably nothing , except perhaps radium , compares with it in human interest . Helium is one of the best examples of a discovery in pure science that has wide commercial application . In 1868 , an eclipse of the sun was visible in India , several scientific men who were in India making observations of the eclipse turned a spectroscope for the first time on the solar chromosphere - that part of the atmosphere of the sun , about 10,000 miles deep , which merges into the corona . A bright yellow line was observed and was thought at first to be due to sodium . Janssen showed , however , that this line was not just the same as either the D or D₂ line of sodium, although it was extremely close to these lines , hence he suggested that the new line have the designation D₂ . Frankland and Lockyer decided that Dz was due to an element in the sun not previously discovered on the earth , and suggested for it the name "Helium" from the Greek work " Helios " the sun . For several years nothing more was done in connection with this element . In 1894 , Sir William Ransay , in conjunction with Lord Rayleigh , made his memorable discovery of argon in the atmosphere , which was announced at the British Association meeting in the same year . After this discovery , Ramsay looked for other sources of the element . Through Sir Henry Miers , he learned that Dr. W. F. Hillebrand , of the United States Geological Survey , had obtained an inert gas from certain uranium minerals , which gas he had decided was nitrogen . Ramsay believed that part of it might be argon ; he obtained from Hillebrand for experimentation , a sample of the mineral , cleveite , one of the uranium minerals , and after extracting gas from the mineral and purifying it , he ran it into a spectrum tube . The lines obtained ' were , however , different from those of argon; among them was the bright yellow line noted by Janssen . Thus was terrestrial heliun discovered .

Jun 1, 1922