Search Documents

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By W. C. Sanborn

The Bureau of Mines program of investigation and development of domestic mineral deposits had as its wartime objective the most effective immediate utilization of these resources in the interest of National security. Since the war, the results of individual projects are being prepared for publication as rapidly as practicable. Numerous chromite deposits were examined, among them those of the French Hill Mine in northern California. Situated 16 miles east of Crescent City, 76 miles from the nearest railroad shipping point at Grants Pass, Oreg., this deposit had a recorded yield of about l4,000 tons of metallurgical-grade chromite to the end of 1943. By the end of 1946, total production was more than 25,000 tons, averaging 43 percent Cr2O3, with a chrome:iron ratio of about 2.5:1.

Jan 1, 1948

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By S. D. Maksimovic

The use of vertical surface degasification boreholes with bleeder systems and the use of a timbered bleeder system to degasify gob areas were studied by the Bureau of Mines. This report describes three gob degasification studies conducted in the Pittsburgh coalbed. One study was conducted to determine the number of panels degasified with one large borehole. The study showed that the borehole provided degasification for three panels. Another study was conducted during the retreat of a 35-acre panel with a single-entry and a two-entry bleeder system and a large surface borehole. A major portion of methane emitted from the panel was carried away by the bore-hole, leaving the bleeder entries relatively free of methane. The last study was made to determine the effectiveness of a timbered bleeder system. The bleeder entries successfully degasified the gob area when enough entries were available and adequate pressure was available to force the air through roof falls.

Jan 1, 1980

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By Louis A. Panek

The practice of roof bolting, now recognized as an effective method of support, is based largely on rule of thumb. Among the various applications of bolting, the support of stratified mine roof is by far the most common. The general principles relating to this type of reinforcement are presented in two companion reports; the first describes the function of the bolts, the bolting pattern, and the behavior of bolted roof (1), 2/ and the second describes the design of the models and the theory of the experimental method (2). This report presents a rational method for designing systems of vertical bolts to reinforce horizontally bedded mine roof, developed from model tests. The structure treated herein may be described as follows: The immediate roof, consisting of beds of like material and equal thickness with no bond between them, is reinforced by vertical bolts installed in straight lines across the opening; the case of suspension is excluded because the bolts are assumed not to extend above the immediate roof. The assumption is made that the behavior of the lowest bed approximates that of a rectangular plate clamped along two opposite sides (the ribs). These specifications represent approximately the roof conditions encountered in mining bedded deposits of all kinds - coal, potash, iron ore, etc. Thus, for the design of a roof-bolting system a quantitative solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, how does the support depend upon the length, spacing, and tightness of the bolts?

Jan 1, 1956

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By R. R. Nothdurft

The internal friction of eight single crystals of magnesium with orienta-tion ranging from 10° to 84° was measured at 33.5 kc and 272° C, and the results were interpreted in terms of the pinned-dislocation model proposed by Granato and Lucke. Results show that the strain-amplitude-dependent decrement varies with orientation in a manner predictable by the G-L model. Different values of strain-amplitude-independent decrement were observed at different orientation angles, but correlation with the theory was not conclusive. Problems and steps for further study are discussed.

Jan 1, 1965

By Robert F. Holub

The U.S. Bureau of Mines (USBM) has tested a personal dosimeter for measuring radon decay products that is manufactured by Tom Scurry Associates. The tests were made to determine the accuracy of the dosimeter system for record keeping of radiation exposures to radon decay products encountered in mining. The radioactivity-detecting head is based on a design developed by the USBM, and the associated air pump was developed by the manufacturer. The dosimeter system was tested in the USBM radon chamber. The detecting head uses CaF:Dy thermoluminescent phosphors and is mounted on a self-regulating air pump. Batteries supply power sufficient for an 8-h shift. The dosimeter system is worn on the miner's belt. Dosimeter calibration tests were performed by the USBM. In addition, the pumps were tested and evaluated under continuous flow conditions. The results of these tests indicate that the Tom Scurry Associates Model DOSI600 dosimeter is suitable for general use in mines where record keeping for natural radiation exposure is required.

Jan 1, 1995

By R. Barany

The heats of formation of gehlenite and talc were determined by hydro-fluoric acid solution calorimetry. The results are reported in terms of the constituent oxides (?H298.15 = -31.1 ± 0.5 kcal/mole for gehlenite and ?H298.15 = -44.9 ± 0.3 kcal/mole for talc) and in terms of the constituent elements (?H298.15 = -952.8 ± 0.7 kcal/mole for gehlenite and ?H298.15 -1,415.5 ± 1.4 kcal/mole for talc).

Jan 1, 1963

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974

By Charles A. Kumke

In June 1942 , ' the Bureau of Mines selected the Zonia copper mine , near Kirkland , Yavapai County , Arizona , as a property meriting investigation in connection with its search for supplies of strategic minerals for use in the war . The following month , representatives of the War Production . Board conferred with Bureau officials and requested that the property be explored with the object of determining the tonnage and grade of ore that could be brought into production quickly and mined cheaply by open-pit methods . The work wa's designed to verify information submitted by the owners in support of an application for a Government loan. It was essential that the investigations be completed promptly , so that operations might be planned and copper produced for war needs . The investigations called for surface trenching , diamond drilling , and check sampling of underground workings . Unable to purchase equipment for trenching without considerable delay , the Bureau saved time by borrowing most of the necessary items from the Golden Queen mine of the Gold Fields Development Co. at Mohave , Calif. This company , whose engineers had sampled some of the old trenches , had a tentative agreement with the owners to operate and manage the Zonia mine in event the loan was granted . Additional equipment was borrowed from two Governmental agencies . The exploratory work , completed in 16 weeks , was carried on 7 days a week .

Mar 1, 1947

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By John H. Soule

Appreciable quantities of sine and lead orus have been produced from the West. Pinos Altos district of Grant County, N. sex. This area was visited many times by engineers of the Bureau of ines. D. H. Johnson and 4. R. Storms visited the district in haren 1943 in connection with an acrenu road to toe wines. M. H. Storma again visited the area in July 1943 in connection with a hetals Feserve Corporation loan on the Routen-Thomas

Apr 1, 1948

By B. A. Rogers

The problem of obtaining enough manganese for use in the manufacture of steel appears likely to recur when international relationships are disturbed and to become serious at any time when the United States is cut off from its customary supply. Some idea of the problems that an e under war conditions may be obtained from a description given by Ellicott3/ in 1918 before the American Iron and Steel Institute. This condition arises because in normal times there is an economic advantage in importing available high-grade foreign ores to the neglect of our own less satisfactory resources. That considerable low-grade manganese ore and a much smaller amount of high-grade material are available in this country is well known from geological surveys 4/ and has been confirmed by Bureau of Mines investigations. Locations of the various deposits are indicated in figure 1. The possibility of greatly expanding domestic production was actually demonstrated from 1913 to 1918, when the annual production of manganese from domestic ores rose from about 4 percent to approximately 35 percent 6/7/ of the total consumption of ferromanganese and spiegeleisen. In idea of how domestic production compares with total consumption in the United States can be obtained 1 from figure 2, taken from the Minerals Yearbook8/ for 1970. Assuming that it is possible to increase production of manganese ores sufficiently to supply all our needs, such a program presumably would require 2 or 3 years, and the cost of production would certainly rice considerably, for some time at least. For

Jan 1, 1941

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991