Search Documents

By W. W. Cutler

An oil-field drilling campaign is used in this paper to signify the spacing of the wells to be drilled as well as the drilling program, which is interpreted as the number of wells drilled in a unit of time, This has an important bearing upon the time of receiving income, as well as upon the amount of revenue obtained In periods of low prices for oil, such as the present, the margin of profit is at the best very small, and the correct determination of the drilling campaign may be the deciding factor between incurring financial loss or gain during the depressed period. General policy of the operator. Drilling should be planned by the field engineer to conform with the general policy of the operator. This policy may be one of conservation daring the early life of the property, but as mentioned later, this may result in a smaller ultimate recovery it often occurs that the market price of oil does not warrant rapid development, or it may be desirable to hold in reserve a supply of oil for a refinery. The policy may be to recover all of the oil as quickly as possible, or it may be to maintain a constant and sustained production. In any case, the operator should, outline as far as possible a definite policy, and should understand the principles underlying the recovery of oil, the influence of rapidity of drilling and effects of spacing, in order that he may obtain the oil as required with the least expenditure.

Jan 1, 1921

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

By Helen W. Lang

This report describes a monitoring system applied by the Bureau of Mines to provide rapid, continuous determination of the main constituents of exhaust gas during the Bureau's approval schedule testing of diesel engines for under-ground use. Commercially available continuous analyzers with strip chart readout are employed for nitric oxide (mass spectrometric), carbon dioxide (nondispersive infrared), methane (NDIR), carbon monoxide (NDIR), and oxygen (polarographic). Good correlation is obtained between the continuous instrumental results and those obtained by batch chemical and gas chromatographic methods.

Jan 1, 1969

By Walter E. Lewis

This circular presents the method of making tests and apparent results of comparing performance of tungsten carbide insert bits and steel detachable bits by the Cleveland-Cliffs Iron Co. at the company's mines on the Marquette iron range of Michigan. The mines are at Ishpeming and Negaunee, Mich., and include the Cliffs Chaft, Mather "A", Cambria-Jackson, and Mather "B". There are four general characteristic types of high-grade iron ore on the Marquette range. B. H. Boyum2/ classifies the Cliffs Shaft as "hard-ore" and the Cambria-Jackson and Mather "A" as "soft-ore" types of deposit. Shaft sinking through Jasper, slate, and graywacke was in progress at this writing at the Mather "B", with completion at 3,100-foot depth in August 1949. The many different kinds of rock and ore at the mines of the Cleveland- Cliffs Iron Co. and the experimental work being carried on with carbide in- sert bits make it possible to compare, generally, the carbide insert and steel detachable bit. The type of "hard ore" at the Cliffs Shaft mine re- quired close study of the possible use of the insert tit, and their records are more complete than those of the "soft-ore" mines. History and development of tungsten carbide tips inserted in rock drill bits have been covered by R. W. Adamson, C. H. Vivian, R. C. Sullivan,5/ and others. Tungsten carbide insert rock bits have only recently been introduced to the domestic mining industry. Although unusual performance records are being reported at operations employing the insert bits, the general adaptability of the tool to all rock types and the advantages to be gained by using carbide insert tits remains to be demonstrated. Insert-bit performance is being observed at numerous mines and quarries throughout the United States The several mining operations at the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., is one site where exhaustive comparative tests of insert and conventional steel detachable bits are currently in progress. Results to date are sufficiently impressive to be of general interest to the mining

Mar 1, 1950

By R. V. Ramani, K. Bode

"IntroductionIn part 1 of this paper, the results of the experimental work in a wind tunnel under controlled conditions were presented. To understand the spatial and temporal behaviour of airborne dust under mine conditions, experiments were performed in the Lake Lynn Experimental Mine of the US Bureau of Mines. The mine airway experiments were designed to study the variations of ambient concentrations along the length of an airway, and the deposition rates and deposition velocities in an airway cross section. Other objectives of the study were to investigate the spatial and temporal behaviour of airborne dust with regard to air velocity and particle density, the size distribution of the airborne dust cloud as it travels in the airway, and the size distribution of the dust particles deposited along the airway. Other objectives of the study were to compare wind tunnel results with In-Mine results, whenever appropriate.Experimental ProcedureLocationA complete description of the Lake Lynn Laboratory Mine of the US Bureau of Mines (USBM) can be found in the US Bureau of Mines Information Circular 8911 (Mattes et al., 1983). This mine provides excellent facilities for dust experiments. The airway dimensions are similar to those of a coal mine airway. The mine has a drift (D Drift, see Figure 1) that extends almost 500 meters without interconnecting airways, stoppings, or bends. The D drift measures approximately 6m in width and 2,25m in height.The Lake Lynn Laboratory Mine· is ventilated by a variable speed, 75 kW (100 hp), 28,3 m3/s (60 000 cfm) blower fan installed on the top of the ventilation shaft. Air velocities of 1, 1,3 and 1,8 m/s, respectively, could be obtained in the D Drift. However, the temperature changes at the surface can cause small variations in air quantities and velocities underground. The low background dust level in the mine reduces the problem of sample contamination from other sources of dust. Extended periods of uninterrupted data collection can also be scheduled. Mine airway parameters which are important for the analysis include the dimensions of the airway and the ventilation data such as the air velocity, and the pressure loss in the drift. All these data were acquired during altimeter surveys which were conducted prior to each of the experiments."

Dec 1, 1995

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

By J. W. Paul

This circular is one of a series of papers4 on coal-mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of presenting information on present mining methods and certain features which govern costs, safety, and conservation. The methods employed are influenced by natural local conditions with respect to the thickness, character, and dip of the coal bed, the nature of the roof and thickness of the overbearing strata, and the means employed for roof support and its control.

Jan 1, 1929

By G. R. Hopkins

"The average heat requirement per barrel of crude refined in the United States rose from 579,000 B. t. u. in 1940 to 584,000 B. t. u. in 1941. This marked the second successive year in which there was an apparent loss in fuel efficiency at refineries. This ""loss"" took place despite an increase in crude runs, which used to be an invariable indicator of a lower average.Probably the chief factor in the increased heat requirement in 1941 was the gain in the over-all gasoline yield from 43.1 percent in 1940 to 44.2 percent in 1941. Possibly another important factor was the further use of obsolete equipment to increase throughput.The refiners used more of all kinds of fuel excapt coke in 1941 than in 1940. However, the only fuels which increased materially in relative importance were refinery gas, which contributed 51.6 percent of the total heat units in 1941 compared with 50.7 percent in 1940, and natural gas, the share of which rose from 17.1 percent in 1940 to 18.0 percent in 1941. The changes in the percentages for the other fuels were as follows: Oil decreased from 25.7 to 24.1 percent; acid sludge fell from 2.7 to 2.5; coal remained at 3.4 percent; and coke (including steam) fell from 0.5 to 0.4 percent.New records for fuel efficiency were set in all three of the districts east of the Mississippi, namely, East Coast, Appalachian, and Indiana, Illi¬nois, etc. All the ether districts reported higher average fuel requirements in 1941, except the Louisiana Gulf and Arkansas-Louisiana inland.Since the year of the first statistics, the refiners have steadily increased their purchases of electricity. In 1941 total purchases were 1,862,996,000 kilowatt-hours, or 11 percent more than in 1940."

Apr 1, 1943

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By David A. Benjamin

The USBM (U.S. Bureau of Mines) studied mines, prospects, and mineralized sites in the Roberts WSA (Wilderness Study Area) in 1984. The 15,090-acre WSA, located 35 miles northwest of Eureka, NV, is underlain by alluvial deposits of Quaternary age, extrusive and intrusive volcanic rocks of Oligocene through Miocene age, and metasedimentary rocks of Cambrian through Permian age. The Roberts Mountain Thrust fault cuts through the WSA, dividing the metasedimentary rocks into upper and lower plate rock units. One mine, the Kelley, which produced 397 tons of lead-zinc ore prior to 1940, and two prospects are within the WSA; no resources were identified. Exploration for precious metal deposits is presently being conducted in and adjacent to the WSA on large claim blocks. The study area contains six sites in and near these claim blocks that have anomalous gold and silver. Detailed exploration is needed to delineate resources. High purity silica rocks are present in the WSA. Barite, phosphate, oil shale, and vanadium occurrences just outside the WSA may extend into it, but no such occurrences were observed during the USBM study.

Jan 1, 1986

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics of positive corona are presented for air in a 2 - in - diam electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig . Results show that current - voltage relationships depend solely on air density . Comparison of data on positive corona with previously published data on negative corona demonstrates a higher sparkover voltage and a wider range of operability for positive corona at temperatures above 375 ° F. The possibility of achieving higher voltages with positive polarity as indicated by these experiments implies several advantages for the use of positive corona in precipitators to allow better removal of suspended material from hot gases . Based on the physics of an ion in an electrical field , a theoretical equation is derived to define current - voltage characteristics of positive corona in terms of air density . Constants for the equation are evaluated from Calculated current - voltage values at different air densities agree reasonably well with experimental data .

Jan 1, 1964

By A. Adams

The quality of hafnium metal produced by the Kroll process depends upon the purity of the hafnium tetrachloride. This investigation of methods for purification of hafnium tetrachloride was undertaken to aid in producing a higher purity hafnium metal than is currently produced by the Kroll process, The quantities of metallic impurities in hafnium metal were decreased by contact with molten alkali-metal chloride salt. Contact was achieved by a semicontinuous process of bubbling gaseous hafnium tetrachloride through a molten salt bath or by a batch process, first fusing the tetrachloride with a combination of alkali chlorides and then heating the mixture to sublime the hafnium tetrachloride. Low-melting mixtures of sodium, potassium, and lithium chlorides were used to purify hafnium tetrachloride. About 30 percent of the initial hafnium tetrachloride was trapped during purification with alkali- metal chloride salts. The 95-percent confidence limits (6)4 for the amount of oxygen decrease 60 and 34.3 parts per million when the batch purification is combined with a reduction so that both take place in the same equipment,

Jan 1, 1961

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By E. C. Lane

The motor gasoline which is being marketed in the United States this summer is apparently more volatile than the gasoline sold a year ago. In fact the average volatility of this summer's gasoline is almost the same as the average volatility of the gasoline marketed last winter. During the past seven years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fourteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1926

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955